Cold Spray Deposition on Polymeric and Composite Substrates
Antonello Astarita,Luca Boccarusso,Luigi Carrino,Massimo Durante,Alessia Serena Perna,Antonio Viscusi
DOI: https://doi.org/10.1007/978-3-030-42756-6_4
2020-01-01
Abstract:The aim of this chapter is to bring together, summarize and explain the latest development in the field of the cold sprayCold spray deposition on polymeric and compositeComposites substrates. Although the deposition on metallic substrates has been widely studied and there are interesting books reporting the phenomena occurring and describing the process in detail, the deposition on polymeric substrates is a relatively new branch of cold spraying and to date there are no review papers or books focused on this topic. Several original research papers dealing with this topic have been published in the last years so it can be assumed that the available material is enough to allow the writing of a book chapter that summarizes what was done and highlights what more needs to be done. First it is worth to notice why this topic is of interest. PolymerPolymer matrix compositesComposites (PMCs) are widely used in the aerospace industry and in the military because of their low density, high specific strength and stiffness, and other unique properties such as ease formation and machining, well size stability. At the same time the use of polymeric components in aircraft, automobile, and power sector has gradually increased due to the development of new polymersPolymer with enhanced mechanical and physical properties. Some special characteristics such as electrical conductivity, thermal conductivity, electromagnetic shielding, erosion and radiation protection have to be improved to further widen the fields of application of these materials. Therefore, the surface metallization of a PMC or polymeric substrate is considered to be an effective technique to enhance the above-mentioned surface properties. To date there are several conventional techniques for the polymer metallization. The most common metallization techniques include vapor phase deposition, thermal spray deposition, electro deposition, electroforming and electroless deposition. However, these techniques have disadvantages. High equipment and processing costs, size limitations of workpiece produced by vapor phase deposition-based techniques (deposition in atomic dimension and workpiece should be placed in a limited cavity). Low adhesive force, poor stability in the electroplating case and the consequent pollution it generates, long production cycle and high cost of the mold for electroforming, distortion of the substrate surface resulting from the molten particles, and high-temperature flames in thermal spraying (TS). Recently, the cold sprayCold spray technique, with suitable modification, has been increasingly used for the metallization of polymersPolymer and PMCs, especially for the advance polymer compositeComposites such as carbon fiber-reinforced polymer (CFRP). Compared to the techniques mentioned in the previous indent the cold spray offers some intriguing advantages when spraying metallic particles on polymeric substrates: (i) the deposition is made possible by the significant plastic deformation of the particles and of the substrate, some polymers (the thermoplastic ones) can experience an huge amount of plastic deformation so this type of interaction easily occurs; (ii) no chemical reaction are required to take place between the particles and the substrate, so it is not a problem the fact that due to their different chemical nature it would be almost impossible to observe a chemical bonding between a metal and a polymerPolymer; (iii) compared with thermal spray processes a less heat input is required in cold sprayCold spray, therefore, heat effects such as surface distortion, oxides, void, phase transformation, and residual stresses are considerably reduced in the coatingsCoatings; on this premise cold spray appears to be a suitable technique to process temperature-sensitive materials, such as polymersPolymer; (iv) in addition, CS has a technical advantage (similar to the TS)—the spraying gun can be held by a robot arm or the workpiece can be installed onto a numerical control working platform to prepare large-sized or complex surface parts with flexibility and compatibility, and this can be a big competitive advantage in the realm of additive manufacturingAdditive Manufacturing (AM). In this chapter it will be provided a comprehensive overview of the deposition of metallic coatingsCoatings on polymeric substrates through cold spray. The deposition behavior of the coatings and the adhesion mechanisms between the substrate and the particles will have discussed to set a foundation for the practical application of cold spray on polymers. The microstructure and the properties of the coatings will be as well reported to provide a useful guideline for practical applications. Moreover, a section will be devoted to the study of the tailored design of the PMCs substrates and to the study of proper chemical formulations of the polymersPolymer to facilitate the cold sprayCold spray deposition. The main topics that are covered in this chapter are below reported:Different experimental set up adopted;Various substrate/coatingCoatings configurations that can be produced;Mechanisms that rule the adhesion between the particles and the substrate;Deposition behavior and influence of the primary process parameters;Mechanical, tribological, and physical properties of the coatingsCoatings, including microstructure;ModelingModeling of the process;Tailored design and production of the PMCs to facilitate the deposition;Tailored chemical composition of the polymersPolymer to facilitate the deposition; andDirection of further investigation.