Abstract:Magnesium-zinc-calcium alloys have unique advantages of being used as biomedical bone implants since their mechanical properties and biocompatibility are similar to human tissues. However, insufficient strength and poor corrosion resistance have been the major problems to stunt the application. In this paper, the changes of microstructure, mechanical properties and corrosion resistance of ternary Mg-3Zn-0.2Ca (wt.%) with different contents of Mn (0.3, 0.5, 0.7, 0.9, wt.%) are studied. With the increase of Mn content, the grain size of as-cast alloy first decreases and then increases, this indicates that the amount of Mn affects the degree of subcooling of the alloy. At the 320°C/24 h homogenizing treatment, the large and uneven dendrites are transformed into uniform equiaxed grains, the mechanical properties of alloys with different Mn contents are different on the basis of Mg-3Zn-0.2Ca (wt.%) alloy. The five alloys were extruded into bar with a diameter of 8 mm through hot-extrusion process. Quaternary Mg-3Zn-0.2Ca-XMn (X = 0.3, 0.5, 0.7, 0.9) (wt.%) alloys are investigated and the results show that 0.5 wt.% Mn alloy has the best yield tensile strength (YS) (302 MPa) and good ultimate tensile strength (UTS) (327 MPa). The reason is that the different contents of Mn restrain the dynamic recrystallization in extrusion process, which remarkedly reduced the grain size. Moreover, each alloy is investigated by electrochemical measurements at 37°C in a simulated body fluid (SBF). The electrochemical results show that the corrosion potential of Mn-contained alloys are increased compared to ternary Mg-3Zn-0.2Ca (wt.%) alloy, and 0.5 wt.% Mn-contained alloy performs the best result.

Calcium-Containing Aluminum Alloys

Investigation of the Effect of Cerium on the Structure and Properties of Calcium-Containing Aluminum Alloys

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

Effect of Ca Content on the Mechanical Properties and Corrosion Behaviors of Extruded Mg–7Li–3Al Alloys

Effects of Ca addition on the microstructure and mechanical properties of Mg–Zn–Sn–Mn alloys

Effect of Mn Element Addition on the Microstructure, Mechanical Properties, and Corrosion Properties of Mg-3Zn-0.2Ca Alloy

Influence of Ca Content on Microstructure and Mechanical Properties of Extruded Mg–Al–Ca–Mn Alloys

Hypereutectic Al-Ce-X (X=Mn, Cr, V, Mo, W) alloys fabricated by laser powder-bed fusion

Enhancing tensile strength of Mg–Al–Ca wrought alloys by increasing Ca concentration

Phase Composition and Structure of Al–Cu–Mn–Mg–Zn–Fe–Si Alloys Containing 2% Cu and 1.5% Mn

Microstructures, Mechanical Properties and Corrosion Resistances of Extruded Mg-Zn-Ca-Xce/La Alloys

Study of the effect of calcium on structure, physicomechanical and technological properties of deformable alloy Al-3%Mg-0.8%Mn

Enhanced Mechanical Properties and Isotropy of Mg-2Al-0.8Sn Alloy through Ca Addition

Role of Al addition in modifying microstructure and mechanical properties of Mg-1.0 wt% Ca based alloys

Principles for Creating Aluminum-Based Alloys Sparingly Alloyed with Scandium

Multi-alloying effect of Ti, Mn, Cr, Zr, Er on the cast Al-Zn-Mg-Cu alloys

Microstructure and Mechanical Properties of As-Cast Al-10Ce-3Mg-xZn Alloys

Effect of Ca addition on microstructure and mechanical properties of Mg–3.8Al–1.1Sn alloys

Elucidation of formation and transformation mechanisms of Ca-rich Laves phase in Mg-Al-Ca-Mn alloys

Effect of Mn on eutectic phase equilibria in Al-rich Al-Ce-Ni alloys

Formation of Phases and Microstructures in Al-8Si Alloys with Different Mg Content