Abstract:Since the formation of reversed austenite during critical tempering treatment is an important factor affecting the mechanical properties of 13Cr4Ni martensitic stainless steel, a detailed study of the content and morphology of reversed austenite in heat treatment is needed. In this study, the variation curves of a reversed austenite volume fraction with holding time at different tempering temperatures were measured by in situ X-ray diffraction (XRD), and the reversed austenite and carbides of each process were evaluated by transmission electron microscopy (TEM). The austenite content shows a parabolic change with the increase in the tempering temperature; the maximum can reach a peak of about 6.8% at 610 °C, and drops to 0% at 660 °C. It also shows a parabolic change with the extension of the holding time, reaching a maximum of about 9.2% at 5 h of holding time, and a decreasing trend at 10 h of holding time, about 6.8%. The results show that the precipitation of carbides in the microstructure causes elemental segregation at grain boundaries and inside, which is one of the main factors affecting the thermal stability of reversed austenite formation. The kinetic process of reversed austenite during the tempering process was simulated using the JMAK model and the KM model, which can describe the trend of reversed austenite content during the tempering process. Combining the two models, a mathematical model for the room-temperature reversed austenite content under different processes was obtained, and this can predict the room-temperature austenite content.

Beneficial effect of reversed austenite on the intergranular corrosion resistance of martensitic stainless steel

Clarify the effect of reversed austenite on the pitting corrosion resistance of super 13Cr martensitic stainless steel

Impact of Reversed Austenite on the Pitting Corrosion Behavior of Super 13cr Martensitic Stainless Steel

Prominent role of reversed austenite on corrosion property of super 13Cr martensitic stainless steel

Reversed austenite in additively manufactured martensitic stainless steel

Advancement of strength and toughness in ultra-low carbon martensitic stainless steel by reversed austenite

Study on the Mechanical Stability of Reversed Austenite in Super Martensitic Stainless Steel Via In-Situ Synchrotron High Energy X-ray Diffraction

Numerical Simulation of Reversed Austenite Evolution during Intercritical Tempering of Low-Carbon Martensitic Stainless Steel

Effect of Retained Austenite on Austenite Memory of a 13% Cr–5% Ni Martensitic Steel

Improved Corrosion Resistance of Super Austenite Stainless Steel by B-induced Nucleation of Laves Phase

Reversed Austenite Growth Behavior of a 13%Cr-5%Ni Stainless Steel During Intercritical Annealing

Effect of deformation induced martensite on electrochemical behaviors of type 304 stainless steel in the active state

Influence of deformation-induced martensite on stress corrosion cracking of AISI 321 stainless steel

Enhancing Ductility of Martensitic Steels Through Cryogenic Treatment

Reverse-Martensitic Hardening of Austenitic Stainless Steel Upon Up-quenching

Austenite Thermal Stabilization Through the Concentration of Manganese and Carbon in the 0.2c–5mn Steel

Effect of Aging on Transformation Behavior of Reverted Austenite and Toughness in Co-Free Maraging Stainless Steel

Phase-field simulation of austenite reversion in a Fe-9.6Ni-7.1Mn (at.%) martensitic steel governed by a coupled diffusional/displacive mechanism

Exploring the effects of austenitizing conditions on the heterogeneous microstructure and mechanical properties of 11Cr–11Ni–Ti–Mo maraging stainless steel: Breakthrough in the strength-ductility trade-off

Microstructure Evolution and Orientation Relationship of Reverted Austenite in 13cr Supermartensitic Stainless Steel During the Tempering Process

The Negative Effect of High-Intensity Shot-Peening on the Intergranular Corrosion Behavior of the Super304H Austenitic Stainless Steel