Abstract:As the power density of the power transmission device increases, heat exchangers are required to dissipate more heat and provide better flow resistance in the limited space of the vehicle. In this study, the synergy mechanism of the temperature field, pressure field, and velocity field in the serrated fin channel of the plate-fin heat exchanger (PFHX) was thoroughly analyzed under the guidance of the three-field synergy principle. This study also quantitatively revealed the distribution of the angle θ between the temperature gradient and velocity, and the angle α between the pressure gradient and velocity. For the regions in the channel where θ was too large (i.e., poor synergy between temperature and velocity fields) and α was too small (i.e., poor synergy between pressure and velocity fields), high-efficiency and low-resistance fin structures were proposed. The performance improvement of the new structures was quantified using the comprehensive heat transfer and flow resistance performance evaluation plot in the three-field synergy standard. The results indicate that the new structures improve the synergy of the three fields in the channel. When the air velocity is 15 m s −1 , the average synergy angle θ m between the temperature gradient and the velocity of the two structures, changing the inlet flow direction and the slotted fin, decreases from 83.4° to 80.3° and 82.8°, respectively. The outlet temperature increases by 2.3 and 1.6 K, respectively, compared to the basic structure, indicating enhanced the heat transfer of the PFHX. By changing the shape of the fin cross-section, the average synergy angle α m between the pressure gradient and the velocity increased from 143.6° to 150.8°, while θ m increased by only 0.6°. The pressure loss was reduced by 15.2% compared to the basic structure, resulting in a significant decrease in pressure drop while maintaining essentially the same heat transfer performance. Meanwhile, the optimized PFHX can increase the heat transfer rate by 0.2%–8% under identical pump power. This work provides guidance on selecting high-efficiency and low-resistance vehicle-mounted PFHXs.

Heat transfer enhancement using non-equally structure in a plate-fin heat exchanger with offset fins

Segmented Design of Performance Enhancement for Large Plate Fin Heat Exchanger of Cryogenic Air Separation Unit

Thermal Design of Large Plate-Fin Heat Exchanger for Cryogenic Air Separation Unit Based on Multiple Dynamic Equilibriums

A Numerical Study on the Air-Side Heat Transfer of Perforated Finned-Tube Heat Exchangers with Large Fin Pitches

Numerical Analysis of Header Structure Improvement in a Plate-Fin Heat Exchanger

Numerical study on hydrodynamic characteristics of plate-fin heat exchanger using porous media approach

Augmentation of Plate-Fin Heat Exchanger Performance with Support of Various Types of Fin Configurations

Enhancing Plate-Fin Heat Exchanger Hydraulic Thermal Performance Through Air-Side Fin Optimization Based on Pseudo-3D Topology Optimization

On the Heat Transfer Enhancement of Plate Fin Heat Exchanger

Exploration and numerical study of new structures for high-efficiency and low-resistance vehicle-mounted plate-fin heat exchanger based on the three-field synergy principle

Effect of Inlet Flow Maldistribution on the Passage Arrangement Design of Multi-Stream Plate-Fin Heat Exchanger

Effect of flow maldistribution on heat transfer performance and temperature field of plate-fin heat exchangers

Numerical Study of Fluid Flow and Heat Transfer in Plate-Fin Heat Transfer Exchanger of Htgr

Performance Investigation of an Innovative Offset Strip Fin Arrays in Compact Heat Exchangers

Numerical Modeling and Experimental Verification of Flow and Heat Transfer over Serrated Fins at Low Reynolds Number

An Experimental Study on the Offset-Strip Fin Geometry Optimization of a Plate-Fin Heat Exchanger Based on the Heat Current Model

An Experimental and Numerical Investigation of Air Side Heat Transfer and Flow Characteristics on Finned Plate Configuration

Effects of Distribution Channel Dimensions on Flow Distribution and Pressure Drop in a Plate‐Fin Heat Exchanger

Heat transfer enhancement investigation in a novel flat plate heat exchanger

Numerical simulation of heat transfer and flow characteristics for plate fin-and-tube heat exchanger with ring-bridge slit fins

CFD-based structure optimization of plate bundle in plate-fin heat exchanger considering flow and heat transfer performance