Abstract:EPB shield tunnel construction will discharge a large amount of soil. Directly transporting this discharged soil to dumping grounds not only increases the machinery and labor costs but also raises environmental concerns. In this paper, we presented and explored a guiding framework for recycling the discharged soil from EPB shield tunnel construction as the raw materials for synchronous grouting. The proposed method was proved to be feasible by a detailed experimental study based on samples taking from the Zhengzhou metro line 3 project. The preparation and formulation process of those raw materials was designed to meet the requirements not only for engineering application but also for green environmental protection and sustainable development. The properties and performance of the synchronous grouting material, including its specific gravity, fluidity, gel time, bleeding rate, bulk shrinkage rate and unconfined compression strength, were investigated by the U15* (154) uniform design experimentation. The effects of ratios of water/binder (cement + fly flash), the binder/coarse-grains (the discharged soil from the west bound tunnel + river sand), fine-grains (the discharged soil from the east bound tunnel)/water and the fly flash/cement on the response value of the synchronous grouting material performances have been investigated with stepwise nonlinear regression analysis model and 3D response surface diagrams. Moreover, the optimal mass ratio for the synchronous grout is also proposed with a new Goal Programming model to obtain an optimum performance. The results indicate that the discharged soil from the east bound tunnel in this project can be directly reused as bentonite, while the discharged soil from the west bound tunnel should be mixed with river sand at a mass ratio of 1:1 before reusing it as the raw material of synchronous grout. Furthermore, the performance of the synchronous grouting was demonstrated highly depending on the proper selection and optimization of mass ratios for water/binder, binder/coarse-grains, fine-grains/water and fly-ash/cement. The presented experimental investigation and the proposed strategy for determining the optimal formulation for synchronous grouting materials demonstrated a feasible way of recycling discharged soil from EPB shield tunnel construction.

Development and Field Test of New Environmentally Friendly Water-Rich Sand Grout Material

Sedimentation-affected Engineering Performances and Microstructures of a Hybrid Portland- Sulfate Aluminate Cement Grout Cast in Long Tubes

Feasibility Study on Preparing Economical and Environmentally-Friendly High-Flowability Ultra-High Performance Cementitious Composites with Original Graded Stone Powder Free Recycled Manufactured Sands

Utilization of Solid Waste from Tunnel Excavation As Manufactured Sand with Different Lithology and Pre-Washing Process for Preparation of Eco-Friendly Ultra-High Performance Concretes: Properties and Microstructural Analysis

Study on Comprehensive Treatment Method of Curtain Grouting in Water-Rich Sand Layer

Research on Sustainable Development of Fine-Grained Material Cement Slurry

Development and application of novel microfine cement-based grout

Material innovation and performance optimization of multi-solid waste-based composite grouting materials for semi-flexible pavements

Study on the mechanical properties and microstructure of a rich-watered grouting material

Investigation and practical application of a new cementitious anti-washout grouting material

Experimental study on new grouting material of acidic sodium silicate and its properties of grouted-sand

Properties and field application of the grouting material for water blocking during thawing of frozen wall of deep sand layer

Experimental research on mechanical performance of grouting plugging material with large amount of fly ash

In situ resource reutilization of earth pressure balance (EPB) shield muck for the generation of novel synchronous grouting materials

Workability and Environmental Evaluation of Using Sunflower Stalk Ash as an Alkali Activator with Blast Furnace Slag and Black Rice Hull Ash to Prepare Geopolymer Grouts

Reusing Fine Silty Sand Excavated from Slurry Shield Tunnels as a Sustainable Raw Material for Synchronous Grouting

Comparative study on the mechanical properties of solidified silty-fine sand reinforced by permeable polymer and traditional grouting materials

Experimental Investigation of Synchronous Grouting Material Prepared with Different Mineral Admixtures

Recycling of discharged soil from EPB shield tunnels as a sustainable raw material for synchronous grouting

Study of Mechanical Properties of Sand Layer Grouting Reinforcement under Seawater Erosion

Experimental Study on Mineral Solid Waste Green Grouting Material Based on Electromagnetic Characteristic Detection