Abstract:Flexural Properties of Al‐CFRP Riveted Laminates Under Three‐Point Bending. This study aims to investigate the bending performance and evaluation of aluminum‐carbon fiber reinforced plastic (Al‐CFRP) riveted laminates under varying parameters via self‐pierce riveting and three‐point bending tests. Through the self‐pierce riveting process test, a riveted joint meeting standard requirement was obtained. Based on this joint combination form, Al‐CFRP self‐pierce riveted laminates were prepared. The bending performance test showed the riveted laminate with a span of 80 mm had the greatest bending resistance at a thickness of 2 mm, and the overall strain of the Al‐CFRP self‐pierce riveted laminates was observed by digital image correlation (DIC) technology. Subsequently, validated numerical simulation modeling was conducted by correlating with the test results. On this numerical simulation model basis, further parametric studies and bending performance evaluations (including number of rivets, CFRP lay‐up angle, and laminates width) of the Al‐CFRP self‐pierce riveted laminates were systematically carried out. It was found that the peak load F and bending strength R improved by 1.32% and 26.66%, respectively, while the mass M reduced by 8.99%, for the design variables of var1 of 20 mm, var2 of 6, and var3 of [0/90°]2s. Highlight An Al‐CFRP riveted laminate structure is proposed to improve the bending properties of riveted laminates by changing the rivet parameters and laminate parameters. The bending properties of riveted laminates with different spans were investigated under three‐point bending loading conditions. The DIC technique observed the changes in the strain field of riveted laminates during bending. The effects of different structural parameters on the bending performance of Al‐CFRP riveted laminates were investigated by numerical simulation. An evaluation method combining the gray correlation degree and the combination assignment method is proposed to obtain the optimum riveted laminate structure under bending load conditions.

Fatigue performance of CFRP/aluminum alloy riveted joints

Stress, damage, and fatigue performance analysis of CFRP/Al double-sided countersunk riveted joints with variable rivet-hole clearance

Study of Mechanical Properties and Failure Mechanism of CFRP-Aluminum Alloy Self-Piercing Riveted-Adhesive Joints

Fatigue behaviour analysis of aluminium alloy riveted single-shear lap joints

Flexural properties and evaluation of Al‐CFRP self‐pierce riveted laminates under three‐point bending loads

Experimental and numerical investigation into tensile and cross tensile responses of CFRP/Al blind riveted-bonded hybrid joints

Fatigue behaviour and life prediction of self-piercing riveted joints in DP590/AA5754 dissimilar sheets

Fretting Fatigue Behavior of Riveted Al 6XXX Components

Fatigue strength of self-piercing riveted joints of carbon fiber reinforced composite and Al5052 alloy plates

Jointing of CFRP/5083 Aluminum Alloy by Induction Brazing: Processing, Connecting Mechanism, and Fatigue Performance

Fatigue Behaviors and Mechanism-Based Life Evaluation on SPR-bonded Aluminum Joint

Fatigue failure mechanisms and probabilistic S-N curves for CFRP–steel adhesively bonded joints

Joint Formation and Mechanical Performance of Friction Self-Piercing Riveted Aluminum Alloy AA7075-T6 Joints

A Non-Uniform Interference-Fit Size Investigation of CFRP/Al Alloys by Riveting Mold Design

Fatigue Behaviour of Steel Elements Strengthened with Stand CFRP Sheets

Investigation on the Residual Stresses and Fatigue Performance of Riveted Single Strap Butt Joints

Influence of thickness combinations on mechanical properties of joints produced by clinch riveting with rigid rivet

Investigation on shear and fatigue performance of CFRP/aluminum alloy single-lap adhesive joint

Formation mechanism and mechanical strength evaluation of hybrid riveted/solid-state bonded aluminium alloy joint

Welding and Riveting Hybrid Bonding of 6061 Al and Carbon Fiber Reinforced Composites

Effect of Adhesive Layer Thickness on Strength of Carbon-Fiber-Reinforced Plastic/Aluminum Bond-Riveted Joints