Regulatory studies of murine methylenetetrahydrofolate reductase reveal two major promoters and NF-kappaB sensitivity.

L. Pickell,P. Tran,D. Leclerc,J. Hiscott,R. Rozen

DOI: https://doi.org/10.1016/J.BBAEXP.2005.09.002

2005-11-10

Biochimica et Biophysica Acta

Abstract:

What problem does this paper attempt to address?

Welding and Riveting Hybrid Bonding of 6061 Al and Carbon Fiber Reinforced Composites

Hongyang Wang,Bin Huang,Jinzhu Li,Nan Li,Liming Liu

DOI: https://doi.org/10.3390/polym14010099

IF: 5

2021-12-28

Polymers

Abstract:Welding and riveting hybrid bonding technology was applied to join 6061 aluminum alloy and carbon fiber reinforced plastics (CFRP). The laser-arc hybrid welding process and stepped rivets were used in the experiments to reduce the impact of the poor heat resistance of composites. The effect of hybrid welding arc current on the formation and mechanical properties of 6061 Al/CFRP joints was studied. Tensile shear load up to 4.65 kN was achieved by adjusting process parameters. The welding process and mode of the fracture were analyzed. The hybrid bonded joint obtained consisted of two parts: a welded joint of Al plate and Al rivet, and a bonded interface between Al plate and CFRP plate. The mechanical properties of the hybrid joint were mainly determined by the Al plate/Al rivet welded joint. The results of the study show that there are three interfacial bonding mechanisms between aluminum and CFRP. In addition to mechanical bonding between the Al plate and CFRP plate, there were also metallurgical bonding of Al-Mg intermetallic compounds with resin matrix and chemical reactions of aluminum with resin and carbon fibers at the interface, which could improve the mechanical properties of the joints.

polymer science
Research on laser rivet welding to achieve hybrid joining of CFRP and high-strength steel

Shiwei Zhou,Dianwu Zhou,Zhaoguo He,Ao liu,Jinshui Liu

DOI: https://doi.org/10.1016/j.optlastec.2024.110992

IF: 4.939

2024-04-10

Optics & Laser Technology

Abstract:In this paper, a novel laser rivet welding method is explored for joining CFRP to high-strength steel. The steel plate is locked between steel rivet and CFRP plate by plug riveting, while the connection between steel plate and rivet are obtained by laser welding based on the coupling of the rotation of displacement machine and linear oscillation of laser heat source. The mechanical properties of hybrid joints are assessed by the maximum drawing load, and microstructure, laser energy and temperature field distribution of joints are also investigated. The results show that the hybrid joints are categorized into steel plate/steel rivet welding area (SRA), CFRP plate/steel plate mechanical contact area (SCA) and CFRP plate/steel rivet riveting area (RCA). When laser heat source oscillates in a straight line, the peak value of laser energy reduces, while the transverse area of laser energy increases, which is beneficial to reducing the thermal damage of CFRP plate. At the optimal parameter, the melting depth in SRA is reasonably controlled, the interface temperature in SCA is lower than that of CFRP resin decomposition, and there is no gap in SCA, the fracture mode of joints presents the characteristic of CFRP matrix tearing failure, and the maximum drawing load of joint reaches 2500 N. However, when the melting depth increases to the thickness of steel plate, the heat effect on CFRP plate becomes severe, and the bond between the resin and carbon fiber wire in base material is destroyed, which deteriorates the performance of steel/CFRP joint.

optics,physics, applied
Process Characterizations of Ultrasonic Extruded Weld-Riveting of AZ31B Magnesium Alloy to Carbon Fiber-Reinforced PA66

Zeguang Liu,Guanxiong Lu,Yuanduo Yang,Sansan Ao,Kaifeng Wang,Yang Li

DOI: https://doi.org/10.3390/polym16121749

IF: 5

2024-06-20

Polymers

Abstract:Traditional metal–plastic dissimilar welding methods directly heat the metal workpiece, which may cause potential thermal damage to the metal workpiece. Ultrasonic extruded weld-riveting (UEWR) is a relatively new method for dissimilar joining of carbon fiber-reinforced thermoplastic (CFRTP) and metal. In this method, the CFRTP workpiece is melted using the ultrasonic effect and is squeezed into prefabricated holes in the metal workpiece to form a rivet structure. In this method, the metal workpiece is not directly heated, and potential high-temperature losses can be avoided. This paper investigates the process characterizations of UERW of AZ31B magnesium alloy to carbon fiber-reinforced PA66. The process parameters are optimized by the Taguchi method. The joint formation process is analyzed based on the fiber distribution in the cross-sections of joints. The effects of welding parameters on the joint microstructure and fracture surface morphology are discussed. The results show that a stepped amplitude strategy (40 μm amplitude in the first stage and 56 μm amplitude in the second stage) could balance the joint strength and joint appearance. Insufficient (welding energy < 2600 J or amplitude-A 2800 J or amplitude-A > 50%) welding parameters lead to the formation of porous defects. Three fracture modes are identified according to the fracture surface analysis. The maximum tensile shear strength of joints at the optimal parameters is about 56.5 ± 6.2 MPa.

polymer science
Bonding mode and mechanical properties of keyhole-free friction stir rivet welded aluminum alloy joints

Peng Zhang,Sheng-dun Zhao,Chuan-wei Zhang,Shun-lai Zang,Zheng Chen,Liang-yu Fei,Yong-fei Wang,Hong Jiang,Fan Li,Hao Zhou

DOI: https://doi.org/10.1016/j.jmrt.2022.02.097

IF: 6.267

2022-05-01

Journal of Materials Research and Technology

Abstract:A novel method called friction stir rivet welding (FSRW) is proposed to combine mechanical interlocking and metallurgical joining, and is expected to improve such mechanical properties and eliminate the keyhole defects in traditional friction stir spot welded (FSSW) joints. The FSRWed joint forms metallurgical joining between the upper and lower sheets, while mechanical interlocking between the rivet and the surrounding plasticized materials. The spindle force, bonding mode, mechanical properties and failure mode of three joints are comparatively investigated to clarify the strengthening mechanism of FSRW method. Results indicate that the keyhole defects are successfully eliminated in FSRWed joints, and the mechanical properties of the joints are considerably improved by using the threaded rivet FSRW (T-FSRW). The spindle force requirement of T-FSRW exhibit greater than that of cylindrical rivet FSRW (C-FSRW). Similarly, compared with the FSSWed joint, the T-FSRWed joint has a 65% higher shear tension strength and 170% increase in cross tension strength, with the corresponding extension at fracture increased by 19% and 220%, respectively. Rivet geometry plays a crucial role on the joints’ mechanical properties, and determines the transverse section and joining parameters. The strengthening mechanism of the FSRW method is assumed from the combination of mechanical interlocking and metallurgical joining. In addition, analysis of the fracture morphologies demonstrate that the shear tension failures of the FSRWed joints mainly exhibit neck, shear fracture and upper sheet tensile fracture, while the cross tension failures exhibit neck fractures and rivet pull-outs.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Research on the formation mechanism and mechanical properties of refill friction stir riveting (RFSR) joints of aluminium alloy AA7075-T6

Huan Zhao,Yunpeng Liu,Yunwu Ma,Xuecheng Ping,Dongzhe Zhang,Yongbing Li

DOI: https://doi.org/10.1016/j.tws.2024.111696

IF: 5.881

2024-02-14

Thin-Walled Structures

Abstract:In this study, a novel refill friction stir riveting (RFSR) process was proposed to achieve hybrid solid-state bonding and mechanical interlocking of high-strength aluminium alloy AA7075-T6 sheets. The size of mechanical interlock is predefined by the depth of groove designed on the rivet shank, and realized through sheet material refilling. High-quality solid-state bonding is also generated at the sheet faying surface under the high pressure and strong friction stir from the rivet. The quality characteristics, microstructure, heat generation, microhardness distribution and mechanical properties were systematically investigated to uncover the joint formation mechanism and verify the effectiveness of the RFSR process. The results reveal that a mechanical interlock with 82% of the predefined value was successfully achieved by sheet material refilling into the groove on the rivet shank. An extra mechanical interlock, which was formed between the rivet shank and trapped bottom sheet, further enhanced the joint strength. Continuous solid-state bonding with a width of 0.39 mm was also generated between the two sheets. Strengthened by the multiple connection features, the peak lap-shear and cross-tension forces reached up to 9.09 ± 0.24 kN and 6.82 ± 0.11 kN respectively, and the corresponding failure modes were rivet shank fracture and pull-out of rivet shank from the bottom sheet.

engineering, mechanical,mechanics, civil
Friction stir riveting (FSR) of AA6061-T6 aluminum alloy and DP600 steel

He Shan,Yunwu Ma,Sizhe Niu,Bingxin Yang,Ming Lou,Yongbing Li,Zhongqin Lin

DOI: https://doi.org/10.1016/j.jmatprotec.2021.117156

IF: 6.3

2021-09-01

Journal of Materials Processing Technology

Abstract:<p>The increasing demand for lightweighting in the automobile industry drives the mix-use of high specific strength materials, such as aluminum alloy and advanced high strength steel (AHSS). However, the differences in physical and metallurgical properties of aluminum alloy and steel, and the increase of steel strength have brought great challenges to the traditional spot joining technologies. This paper proposed a novel friction stir riveting (FSR) process to join aluminum alloy and AHSS sheets. In the FSR process, a high-speed rotating semi-hollow rivet penetrates through the aluminum sheet and is then friction welded with the steel sheet to form an annular solid phase welding zone, which mechanically locks the aluminum sheet between the rivet cap and the steel sheet, creating a solid phase-mechanical hybrid joint. The joint macro morphology formation, the solid phase welding mechanism, the thermo-mechanical coupled effects on microstructures and microhardness, and the tensile-shear performance of the joints were investigated. The results indicate that the FSR process achieved successful joining of AA6061-T6 and DP600. However, the joint performance was limited by a thin layer of inclusion in the solid phase welding zone, which was produced after the rivet cavity being fully filled by the trapped aluminum alloy. Further optimization of the rivet cavity and corresponding process parameters is necessary to obtain an inclusion-free FSR joint. The FSR process is expected to provide a new industrial solution for the joining of light alloy to steel and offers new insight into the solid phase joining of tube-sheet structures.</p>

materials science, multidisciplinary,engineering, manufacturing, industrial
Elucidation of interface joining mechanism of aluminum alloy/dual-phase steel friction stir riveting (FSR) joint

He Shan,Yunwu Ma,Bingxin Yang,Qiaobo Feng,Yongbing Li,Zhongqin Lin

DOI: https://doi.org/10.1016/j.jmrt.2023.07.146

IF: 6.267

2023-07-01

Journal of Materials Research and Technology

Abstract:The mixed use of aluminum (Al) alloy and high strength steel (HSS) is an effective way to reduce the weight of vehicles, which meanwhile brings great challenges to the traditional spot joining technologies. Three-stage friction stir riveting (FSR) process using a precisely designed semi-hollow rivet was developed for Al-steel joining. By coordination control the rotation and feed movement of the rivet, a “tube-sheet” annular solid-phase welding zone is formed between the semi-hollow rivet and the lower steel sheet, realizing the reliable joining of Al-steel dissimilar sheets combination. The rivet structure was designed to accommodate the trapped Al alloy in the rivet cavity during the friction welding stage, obtaining an inclusion-free friction welding interface which was not only mechanically mixed but also fully interatomic binding. The optimal FSR joint is composed of ferrite softening zone (FSZ), carbide precipitation zone (CPZ), ultrafine martensite zone (UMZ), and fine dual-phase zone (FDPZ). Moreover, due to the circumferential flow of materials during friction welding stage, the dynamic recrystallization (DRX) microstructures of the rivet and steel sheet both have shear texture consistent with {112}<111> and {110}<001> cube texture, which brings the uniformity of microstructure and performance. With the combined contribution of inclusion-free joining interface and the microstructure with uniform cube texture, the optimal FSR joints have the maximum average tensile-sheer strength of 281.1 MPa (90.7%·σ6061-T6) and peak load of 5.29 kN, presenting pull-out fracture mode with good fracture energy absorption.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Experimental study and finite element analysis on the joining performance of GF/PP rivets

Yuan Wang,Yong Li,Dajun Huan,Lisha Li,Li Liu,Ye Cheng,Hongquan Liu

DOI: https://doi.org/10.1177/0892705720939142

IF: 3.0272

2020-07-20

Journal of Thermoplastic Composite Materials

Abstract:To improve the performance of thermoplastic composite joints and reduce the weight of joints, glass fiber (GF)/polypropylene (PP) thermoplastic composite rivets (GF/PP rivets) were prepared and tensile test and simulation analysis of GF/PP-riveted single-lap joints were carried out. Based on the tensile test, the optimum extension length of GF/PP rod with different diameters was determined by taking the specific joint strength (the ratio of joint strength to the weight of fasteners) as the evaluation index. The effects of the rivet diameter and the thickness of composite laminates on the specific joint strength and the weight reduction of GF/PP-riveted single-lap joints were studied. The joining mechanism and the failure behavior of GF/PP-riveted joints were analyzed by finite element simulation. The experimental results indicate that the specific joint strength of GF/PP-riveted joints decreased with increasing rivet diameter and laminate thickness. For the same specific joint strength, the weight of fasteners at joints could be reduced by 81.4% and 73.9%, respectively, by using GF/PP rivets instead of steel bolts and aluminum blind rivets. The simulation results show that the change of inclination angle of rivet body would cause the change of failure mode of joints.

materials science, composites
Investigation on the joining process and strength of laser circle welding between Al5052 and CFRP dissimilar materials

Sendong Ren,Yihao Shen,Hao Chen,Wenjian Zheng,Yinghe Ma,Daochen Feng,Jianguo Yang

DOI: https://doi.org/10.1016/j.jmapro.2024.04.068

IF: 5.684

2024-04-30

Journal of Manufacturing Processes

Abstract:Laser welding is an effective approach to joining metal and composite. In the present research, laser circle welding was proposed to join the Al5052 sheet and PA6-CFRP as the first try. A process window was suggested according to the welding results and joint appearance. Single lap shear test was employed to evaluate the mechanical performance of welded joints under different welding conditions. The cross-section and fracture surface were subjected to multi-scale characterizations to subdivide the joining zone and understand the joining process. The result showed that 10 sets in 18 groups of welding parameters can achieve successful bonding. The welding results can be classified into four categories: non-connected, aging-failing, effective-joining and burn-through. The joining zone of laser circle welding was divided into three subregions. The adhesive zone (AZ) presented an interfacial fracture while the local failing passed through plastics basement in cohesive (CZ). The overheating of CFRP generated decomposed zone (DZ). The signal peak of O-C=O bond disappeared in the entire joining zone on CFRP sheet and the intensity of carbide was significant in DZ. The laser circle welded joint presented brittle and ductile fracture modes, which were related to the joining zone component. The joining strength can reach about 656 ± 22 N, 2135 ± 331 N and 3223 ± 257 N under one-circle, double-circle and three-circle scanning, respectively. Increased scanning numbers can decrease the required laser power and improve joining strength by extending heating time, while it also increased the risk of burn-through.

engineering, manufacturing
Study on the joint formation mechanism and performance of resistance rivet welding of Mg/steel dissimilar materials

Liangyu Fei,Hao Li,Zhiyan Feng,Fei Jiang,Yiming Zhang,Shengdun Zhao

DOI: https://doi.org/10.1016/j.jmrt.2023.06.084

IF: 6.267

2023-07-01

Journal of Materials Research and Technology

Abstract:In this paper, a new resistance rivet welding process (RRW) is used to achieve the joining of Mg alloy and steel. A rivet is utilized to pierce the upper Mg plate during the welding process and then welded to the lower steel plate. It realizes a metallurgical bond between the rivet and the steel plate, and a hybrid rivet-welded joining between the steel plate and the Mg plate. The joint morphology, forming mechanism, microstructure, and mechanical performance of RRW joints were investigated. And the role of welding current variations on the failure mode and mechanical properties of the joint was studied. The results showed that at welding currents between 11 kA and 13 kA, the main bearing area of the joint was primarily the Mg plate base material. As the welding current increased, the bonding location between the Mg refilled into the rivet cavity and the Mg plate could also be subject to more load, significantly affecting the mechanical properties and failure mode of the joint. The RRW joints achieved a tensile-shear load of 6.08 kN and an energy absorption value of 8.95 J at the optimum parameters.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Fatigue performance of CFRP/aluminum alloy riveted joints

Jia Chen,Zhibing Chen,Mingyue Zhang,Ziwei Xu,Jungang Chen,Jiafan Ye,Guoqing Gou,Wei Gao

DOI: https://doi.org/10.1142/s0217979222400252

2022-03-03

International Journal of Modern Physics B

Abstract:Three types of CFRP/aluminum (Al) alloy riveted joints, single-rivet joint, double-rivet joint and three-rivet joint, were prepared by the riveting technique. The fatigue limit of the three-rivet joint was 27.35 MPa. The fatigue failure mechanism of the joint was that Al alloy cracks on the surface of rivet holes and propagates to fail.
Formation mechanism and mechanical strength evaluation of hybrid riveted/solid-state bonded aluminium alloy joint

Yunpeng Liu,Yunwu Ma,Ming Lou,Bingxin Yang,He Shan,Huan Zhao,Yongbing Li

DOI: https://doi.org/10.1016/j.tws.2023.110976

IF: 5.881

2023-07-14

Thin-Walled Structures

Abstract:In this research, an improved friction self-piercing riveting (F-SPR) process with internally threaded rivet and flat die was proposed to achieve hybrid riveted/solid-state bonded connection for low-ductility aluminium alloys . Instead of relying on rivet shank flaring to form mechanical interlock in the existing F-SPR process, a reliable threaded connection was established between the rivet shank and sheets by rapid filling of sheet material into the rivet thread grooves. A perfectly flat joint bottom was formed without inducing large-scale sheet distortion. A series of experimental tests were performed to clarify the joint quality characteristics, formation mechanism and mechanical performance. The results revealed that the quality of newly formed five aluminium threads demonstrated a decline trend from bottom to top. Two kinds of thread formation mechanisms were identified: The mechanism I is solely composed of Filling step and applied to upper four threads; The mechanism II consists of Filling-Fracturing-Welding steps and is applied to the lowest thread. Discontinuous solid-state bonding was formed at the sheet interface around the rivet shank periphery, whilst a bowknot-liked solid-state bonding zone with a weak welded zone and an unwelded zone was formed at the joint centre. Rivet pull-out failure from the bottom sheet was observed for the studied AA7075-T6 joints under both lap-shear and cross-tension loads. The peak loads reached 9.79 ± 0.23 kN and 5.41 ± 0.15 kN in the lap-shear and cross-tension tests, and the corresponding energy absorption was 13.82 ± 0.59 J and 16.42 ± 0.87 J.

engineering, mechanical,mechanics, civil
Study of Mechanical Properties and Failure Mechanism of CFRP-Aluminum Alloy Self-Piercing Riveted-Adhesive Joints

Y. Q. Yan,S. Xu,Y. F. Xing,H. L. Bian,H. F. Wu

DOI: https://doi.org/10.1007/s11029-024-10188-0

IF: 1.7

2024-05-09

Mechanics of Composite Materials

Abstract:The mechanical properties and failure mechanisms of self-piercing riveted-adhesive joints of carbon fiber-reinforced polymers/6061-T6 aluminum plates was investigated. The effects of riveting pressure, aluminum surface treatment, and lap length on the mechanical properties of the joints were analyzed. The microscopic morphology of the joint at each stage of the failure process was obtained by tensile-shear test and electron microscopy scan, on which the changes of CFRP, aluminum plate, rivet, and adhesive layer at different stages were further discussed to reveal the failure mechanism of the joint. The results showed that the joint strength could be improved by appropriately increasing the riveting pressure. The surface treatment of aluminum plate could improve the surface properties of the joint, and the joint strength showed a trend of first increasing and then decreasing with the increase of the sandpaper mesh. Increasing the lap length led to an increase in joint strength; however, when the lap length was increased to a certain value, the increase in joint strength was not obvious. The failure process of the adhesive riveted specimen was from the failure of the adhesive layer to the failure of the rivet, and after rivet failure, the joint failed completely.

mechanics,materials science, composites,polymer science
An Effective Friction Spot Joining Method for Plastic and Aluminum Alloy

Xuhai Xiong,Mingshen Li,Shude Ji,Dejun Yan,Zhenlei Liu

DOI: https://doi.org/10.1002/adem.201900510

IF: 3.6

2019-06-27

Advanced Engineering Materials

Abstract:An effective joining method called friction spot riveting (FSR) is put forward to join AA6061‐T6 and polypropylene (PP) by improving mechanical interlocking. The lap configuration of the upper Al and the lower plastic sheets is employed, and through hole are pre‐fabricated on the upper Al sheets. The results show that the plastic is heated and softened under frictional heat and forging pressure. They are squeezed into the pre‐fabricated holes, forming rivet structures. Sound metal/plastic joints are obtained via rivets made of plastics. Moreover, a tight joining formed at the interface between metals and plastics due to van der Waals bond. However, the main joining mechanism is the mechanical interlocking induced by the plastic rivets. The maximum tensile shear load of the FSR joint reached 288 N. The tensile shear specimens fractured at the plastic rivets between metals and plastics.

materials science, multidisciplinary
Friction self-riveting welding between polymer matrix composites and metals

Xiangchen Meng,Yongxian Huang,Yuming Xie,Junchen Li,Meng Guan,Long Wan,Zhibo Dong,Jian Cao

DOI: https://doi.org/10.1016/j.compositesa.2019.105624

2019-12-01

Abstract:<p>To construct reliable heterojunctions between metals and polymer matrix composites, friction self-riveting welding (FSRW) was proposed, characterized by multi-scale mechanical interlocking and adhesive bonding, to improve mechanical properties. Holes and porous oxide structures were pre-fabricated on the metal sheet. High-quality heterogeneous joints were achieved. Under the frictional heat and forging force, the composites were softened and flowed into the pre-fabricated holes and porous structures via squeezing behaviors from a welding tool, improving macro/micro-mechanical interlocking. The oxide layers also enhanced adhesive bonding. The maximum tensile shear strength reached 27 MPa based on multi-scale mechanical interlocking and adhesive bonding. Joint fracture located at the interfaces between composites and metals, the composites rivets and the intermixing region of fibers. This strategy has the potential to construct reliable heterojunctions between polymers or polymer matrix composites and metals in the fields of aerospace and automotive.</p>
Experimental and numerical investigation into tensile and cross tensile responses of CFRP/Al blind riveted-bonded hybrid joints

Yu Lu,Qiang Liu,Zengbo Zhang,Liuye Qin,Qing Li

DOI: https://doi.org/10.1016/j.compstruct.2023.117077

IF: 6.3

2023-04-01

Composite Structures

Abstract:The application of riveted-bonded hybrid joints between dissimilar materials in vehicle structures has attracted increasing interest. This study aimed to investigate into the responses of blind riveted-bonded hybrid joints connecting carbon fiber reinforced plastic (CFRP) and aluminum alloy (Al) subjected to tensile and cross tensile loads. Joints with two different locking modes were fabricated, and their micro topographies were observed through scanning electron microscope (SEM). The experimental failure modes, force responses and mechanical properties of these joints were analyzed and compared, then numerical models were established for further exploring the failure mechanisms. The results showed that the imperfections of RC joint (CFRP placed on protruding head side) were fewer than that of RA joint (Al placed on protruding head side). RC joints showed superior mechanical properties. The energy absorption of RC joints was 14.20 % higher than that of RA joints in tensile tests. The peak force, failure displacement and energy absorption of RC joints were 21.67 %, 9.59 % and 44.48 % higher than those of RA joints in cross tensile tests, respectively. The simulation results were consistent with the experimental counterparts, with errors limited to 8 %. These numerical models can effectively replicate the failure behaviors and identify damaged areas of the specimens.

mechanics,materials science, composites
Improving the Efficiency of Single Lap Riveted Joints in the Carbon Nanofiller Reinforced Laminated Polymer Composites

K. Kumar,R. K. Verma,J. Ramkumar,S. C. Jayswal

DOI: https://doi.org/10.1007/s40799-024-00746-5

2024-09-14

Experimental Techniques

Abstract:Glass fiber reinforced polymer laminated (GFRPL) composites are extensively used in the development of multiple loading and high performance engineering components. It consists of greater properties, such as enhanced strength-to-weight ratio, and exceptional thermal stability. This plays a vital role in advanced composite manufacturing, that includes automobile parts, aeroplane parts, spaceships, and sporting goods. During manufacturing, the polymeric laminates essentially require the joining procedure while assembling the structural applications; in such cases, the bolted joint is frequently used to connect the different structural components. In the structural design of two-component joints, the component is governed by the durability and joint strength rather than the component capacity. In the joint setup, many types of joints are used to connect the fibrous composite, i.e., adhesive joint, bolted joint, and riveted joint. This work enhanced the riveted joint efficiency of laminated composite plates. The neat GFRPL and modified GFRPL samples were developed at 1, 2, and 3 Wt.% loading of multiwall carbon nanotube (MWCNT). Herein, the effect of MWCNT on single-lap riveted joining behavior and feasibility was investigated. The lap joint aluminum blind rivet with a 5 mm diameter was used to join the two composites' specimens. The tensile test of single lap riveted joint specimen, impact, and Shore D hardness tests were performed to analyze the composite's shear strength, energy absorption, and hardness. The outcome showed that the MWCNT loading enhances the shear strength, ductility, and hardness. The findings revealed that the higher shear strength and maximum failure load capacity were obtained for GFRPL samples modified by 1 Wt.% supplement of MWCNT as compared to the neat GFRPL, 2 and 3 Wt.% samples. The net tension failure occurred between the hole and the structure's side edges. Optimizing the geometrical configuration of the single-lap riveted joint helps reduce bearing failure and applied net tension. The analysis of the riveted joint revealed its potential for further structural applications. Further, the morphological investigation of the fracture surface of the tested specimens and the elemental composition of the developed nanocomposites was explored.

engineering, mechanical,mechanics,materials science, characterization & testing
Study on the microstructure and failure mechanisms for flat resistance element welding-bonding aluminium alloy/Q235 steel joints

Liangyu Fei,Shengdun Zhao,Peng Zhang,Zhiyan Feng,Fei Jiang,Yiming Zhang

DOI: https://doi.org/10.1080/13621718.2022.2116693

2022-09-11

Abstract:A novel method called flat resistance element welding-bonding (FREWB) is proposed to join aluminium alloy to Q235 steel. The microstructure and mechanical performance of FREWB and flat resistance element welding (FREW) were investigated. The microstructure of the nugget was lath martensite. The heat-affected zone of the rivet could be divided into two zones according to the microstructure: the upper-critical heat-affected zone (UCHAZ) and the inter-critical heat-affected zone (ICHAZ). The microstructure of UCHAZ consists of martensite, and the microstructure of ICHAZ consists of martensite and ferrite. The failure mechanisms of the FREW and FREWB joints were analysed. Moreover, an analytical model was established to predict the variation of critical nugget sizes, which provided a relatively good prediction. Abbreviations AB: Adhesive bonding; ABZ: Adhesive bonding zone; BM: Base material; CFRP: carbon fibre reinforced plastic; FREW: Flat resistance element welding; FREWB: Flat resistance element welding-bonding; HAZ: Heat-affected zone; ICHAZ: Inter-critical heat-affected zone; IF: Interface failure; PO: Pull-outfailure; REW: Resistance element welding; RSW: Resistance spot welding; RSWB: Resistance spot welding-bonding; SPR: Self-pierce riveting; UCHAZ: Upper-critical heat-affected zone; UPO: Upper plate poll off failure; WZ: Weldingzone.

materials science, multidisciplinary,metallurgy & metallurgical engineering
A Non-Uniform Interference-Fit Size Investigation of CFRP/Al Alloys by Riveting Mold Design

Xingxing Wang,Zhenchao Qi,Mu Lu,Haicheng Pan

DOI: https://doi.org/10.3390/pr11030962

IF: 3.5

2023-03-22

Processes

Abstract:The interference-fit size has a significant effect on the riveted lap joints of CFRP/Al alloy laminates. The requirements for the interference-fit size are different because of the strengthening of heterogeneous materials. However, in the riveting process of CFRP/Al alloys, the heterogeneous laminates lead to poor structural strength because of the different interference-fit size requirements. Therefore, differently assembled riveting molds are designed to acquire a novel interference-fit size, and the tensile test is adopted to evaluate their tensile properties. In addition, the fracture failure of CFRP/Al alloy laminate riveted lap joints is observed with an ultra-depth-of-field microscope. Finally, the best assembly type is identified as the trapezoid riveting mold combined with an arc riveting die, and the sidewall intersection angle of the trapezoid riveting mold is 66°, which could achieve a suitable interference-fit size and a better mechanical performance.

engineering, chemical
Analysis and optimization of rivet load distribution in multi-rivet connections of thermoplastic composite rivets

Yujie Yan,Yong Li,Dajun Huan,Hongquan Liu,Kang Zhu,Zehui Hu,Hao Liu

DOI: https://doi.org/10.1177/07316844241228801

IF: 3.1

2024-01-22

Journal of Reinforced Plastics and Composites

Abstract:Journal of Reinforced Plastics and Composites, Ahead of Print. GF/PP thermoplastic composite components predominantly employ metallic fasteners, leading to corrosion and weight issues. This study utilized an extrusion process to fabricate GF/PP thermoplastic composite rivets with properties akin to laminated panel materials. Through the controlled application of heat and pressure to the rivet ends, a novel connection structure was established. The article fabricated thermoplastic composite joints with varying end configurations and compared them with metallic rivet joints. Emphasizing the convex form, diverse multi-rivet links were crafted for single-lap tensile samples. Integrating tensile tests and strain gauge measurements, this research explored load distribution patterns across diverse rivet quantities and assessed the impact of size on distribution. Furthermore, finite element software was used to dissect the load distribution patterns and failure mechanisms in the multi-riveted connection structure. Drawing from experimental findings, convex GF/PP rivets exhibited an 18% higher tensile load than metallic ones, with a simultaneous 32% weight reduction. In multi-rivet connections, end rivets demonstrated higher load-bearing capacity. Enhanced spacing and plate width improved load distribution, elevating joint load capacity by 7% (spacing 25 mm to 55 mm) and 6% (width 30 mm to 55 mm). The simulation results indicate that increasing the spacing reduces the stress concentration at the first nail location.

materials science, composites,polymer science

Regulatory studies of murine methylenetetrahydrofolate reductase reveal two major promoters and NF-kappaB sensitivity.

Welding and Riveting Hybrid Bonding of 6061 Al and Carbon Fiber Reinforced Composites

Research on laser rivet welding to achieve hybrid joining of CFRP and high-strength steel

Process Characterizations of Ultrasonic Extruded Weld-Riveting of AZ31B Magnesium Alloy to Carbon Fiber-Reinforced PA66

Bonding mode and mechanical properties of keyhole-free friction stir rivet welded aluminum alloy joints

Research on the formation mechanism and mechanical properties of refill friction stir riveting (RFSR) joints of aluminium alloy AA7075-T6

Friction stir riveting (FSR) of AA6061-T6 aluminum alloy and DP600 steel

Elucidation of interface joining mechanism of aluminum alloy/dual-phase steel friction stir riveting (FSR) joint

Experimental study and finite element analysis on the joining performance of GF/PP rivets

Investigation on the joining process and strength of laser circle welding between Al5052 and CFRP dissimilar materials

Study on the joint formation mechanism and performance of resistance rivet welding of Mg/steel dissimilar materials

Fatigue performance of CFRP/aluminum alloy riveted joints

Formation mechanism and mechanical strength evaluation of hybrid riveted/solid-state bonded aluminium alloy joint

Study of Mechanical Properties and Failure Mechanism of CFRP-Aluminum Alloy Self-Piercing Riveted-Adhesive Joints

An Effective Friction Spot Joining Method for Plastic and Aluminum Alloy

Friction self-riveting welding between polymer matrix composites and metals

Experimental and numerical investigation into tensile and cross tensile responses of CFRP/Al blind riveted-bonded hybrid joints

Improving the Efficiency of Single Lap Riveted Joints in the Carbon Nanofiller Reinforced Laminated Polymer Composites

Study on the microstructure and failure mechanisms for flat resistance element welding-bonding aluminium alloy/Q235 steel joints

A Non-Uniform Interference-Fit Size Investigation of CFRP/Al Alloys by Riveting Mold Design

Analysis and optimization of rivet load distribution in multi-rivet connections of thermoplastic composite rivets