Abstract:In the present work, the effect of mineral aggregates (pumice stone and expanded clay aggregates) and chemical admixtures (superplasticizers and shrinkage reducing additives) as an alternative internal curing technique was investigated, to improve the properties of high-performance concrete. In the fresh and hardened state, concretes with partial replacements of Portland cement (CPC30R and OPC40C) by pulverized fly ash in combination with the addition of mineral aggregates and chemical admixtures were studied. The physical, mechanical, and durability properties in terms of slump, density, porosity, compressive strength, and permeability to chloride ions were respectively determined. The microstructural analysis was carried out by scanning electronic microscopy. The results highlight the effect of the addition of expanded clay aggregate on the internal curing of the concrete, which allowed developing the maximum compressive strength at 28 days (61 MPa). Meanwhile, the replacement of fine aggregate by 20% of pumice stone allowed developing the maximum compressive strength (52 MPa) in an OPC-based concrete at 180 days. The effectiveness of internal curing to develop higher strength is attributed to control in the porosity and a high water release at a later age. Finally, the lowest permeability value at 90 days (945 C) was found by the substitutions of fine aggregate by 20% of pumice stone saturated with shrinkage reducing admixture into pores and OPC40C by 15% of pulverized fly ash. It might be due to impeded diffusion of chloride ions into cement paste in the vicinity of pulverized fly ash, where the pozzolanic reaction has occurred. The proposed internal curing technology can be considered a real alternative to achieve the expected performance of a high-performance concrete since a concrete with a compressive strength range from 45 to 67 MPa, density range from 2130 to 2310 kg/m3, and exceptional durability (< 2000 C) was effectively developed.

Performance buildup of concrete cured under low-temperatures: Use of a new nanocomposite accelerator and its application

Effect of Curing Conditions on Property of High Performance Concrete with Composite Mineral Admixture

Early-Age Performance of Graphene-Nanoplatelet-Modified High-Strength Concrete Cured by Electric Thermal Curing in Severe Cold Regions

Effects of nano-alumina on Portland concrete at low temperatures (5 °C)

Effects of alternating positive and negative temperature curing on the mechanical properties of ultra-high performance concrete

Effects of Nano-Caco3 on the Compressive Strength and Microstructure of High Strength Concrete in Different Curing Temperature

Influence of nano-silica on the performances of concrete under the negative-temperature curing condition

Early Age Performance of OPC-GGBFS-Concretes Containing Belite-CSA Cement Cured at Sub-Zero Temperatures

The Influence of Alkali-Free Shotcrete Accelerators on Early Age Hydration and Property Development within Cement Systems

Hydration, mechanical properties and durability of high-strength concrete under different curing conditions

Preparation of Nano-Sized C-S-H and Its Acceleration Mechanism on Portland Cement Hydration at Different Temperatures

Mechanical Properties and Shrinkage of Ultrahigh-Performance Concrete Containing Lithium Carbonate and Nano-Calcium Carbonate

Effect of Nanosilica on the Strength and Durability of Cold-Bonded Fly Ash Aggregate Concrete

The application of C–S–H accelerators in the precast concrete industry: Early-age properties and CO 2 footprint analysis

Study on the mechanical properties and microstructure of recycled concrete reinforced with basalt fibers and nano-silica in early low-temperature environments

Electric induced curing of graphene/cement-based composites for structural strength formation in deep-freeze low temperature

Ohmic heating curing of electrically conductive carbon nanofiber/cement-based composites to avoid frost damage under severely low temperature

Mechanical and Microstructural Properties of Nanoconcretes Exposed to Low-Temperature Curing

Effect of Mineral Aggregates and Chemical Admixtures as Internal Curing Agents on the Mechanical Properties and Durability of High-Performance Concrete

An alternative method for performance improvement of ultra-high performance concrete by internal curing: Role of physicochemical properties of saturated lightweight fine aggregate

Effect of nanomaterials on the mechanical properties and microstructure of cement mortar under low air pressure curing