Abstract:The thread and spline synchronous rolling process can form the external threaded and external splined tooth profiles on different parts of component by only one rolling process. However, it is a coupled rolling process where the thread rolling coupling with the spline rolling, and both phase adjusting requirements of dies before rolling for thread rolling and spline rolling should be satisfied in the synchronous rolling process. Thus, the phase adjustment only by rotating die may be difficult to ensure the thread and spline rolling by different dies well connects respectively. In this paper, requirements of phase difference adjustment for dies before thread rolling and before spline rolling have been studied systematically, and the mathematical expressions of phase difference adjustment have been established, and then the requirements of phase difference under different starts of threaded workpiece and die (or teeth of splined workpiece and die) for two and three rolling dies before thread rolling (or spline rolling) have been investigated. Based on these, the ratio S of phase difference between corresponding threaded sections of rolling dies to that between corresponding splined sections of rolling dies was introduced, and the phase characteristic between dies and the method of phase difference adjustment under different parameters in thread and spline synchronous rolling process were systematically researched. The results indicated that: (1) for thread (or spline) rolling process, if the remainder from dividing the starts nw of thread (or teeth Zw of spline) of workpiece by number N of rolling dies is equal to the remainder from dividing the starts nd of thread (or teeth Zd of spline) of rolling die by N, i.e., nw≡nd(mod N) (or Zw≡Zd(mod N)), then the phases of dies before rolling are the same, else there is a phase difference between dies; (2) for thread and spline synchronous rolling process, if the phase difference of splined section between rolling die j (j = 2,…, N) and rolling die 1 is φsj1=hNθsh=1,…,N$$ {\varphi}_{{\mathrm{s}}_{j1}}=\frac{h}{N}{\theta}_s\left(h=1,\dots, N\right) $$ and ratio of phase difference is Sj1=Nhk+1k=0,1,2,3,…$$ {S}_{j1}=\frac{N}{h}k+1\left(k=0,1,2,3,\dots \right) $$, then the die structures of two dies are the same, i.e., the relative phase between threaded and splined sections for two dies are the same, else the die structures of rolling dies j and 1 are different and the phase difference for threaded sections of rolling dies and the phase difference for splined sections of rolling dies are assured by die structure itself.

Influence of geometric parameters on variation of motion during rolling process of involute spline

Motion Characteristic Between Die and Workpiece in Spline Rolling Process with Round Dies

Analysis of Motion Between Rolling Die and Workpiece in Thread Rolling Process with Round Dies

Influence of Processing Parameters on the Thread and Spline Synchronous Rolling Process: an Experimental Study.

Analysis of Forming Error During Thread and Spline Synchronous Rolling Process Based on Motion Characteristic

Rotatory Condition at Initial Stage of External Spline Rolling

Influences of Friction Condition and End Shape of Billet on Convex at Root of Spline by Rolling with Round Dies

The Design and Simulation of Roller for Machining Involute Spline

Implementing approach of rolling process for inner spline sleeve with medium diameter: radial-feed rolling and through-feed rolling

Process Parameter Determination of the Axial-Pushed Incremental Rolling Process of Spline Shaft

Phase characteristic between dies before rolling for thread and spline synchronous rolling process

A Note on Phase Characteristic among Rollers Before Thread or Spline Rolling

Metal flowing of involute spline cold roll-beating forming

Influences of machine-tool setting errors on mesh behavior for small-module spiral bevel gear

Theoretical Analysis and Numerical Simulation of External Spline Cold Rolling

A Numerical Study of the Effects of Roller Paths on Dimensional Precision in Die-Less Spinning of Sheet Metal

Influence of the rotational speed ratio of rollers on the three-dimensional surface rolling process

Research on Divided Flow Method and Temperature Effect of the Incremental Rolling Forming Process for Spline Shaft

Study on the improvements of incremental rolling process for spline shaft with round tools based on finite element method

Parametric Study of Meshing Characteristics With Respect to Different Meshing Rollers of the Antibacklash Double-Roller Enveloping Worm Gear

Research on Fibrous Structure and Surface Work-hardening Test of Cold Rolling Involute Spline