Abstract:Introduction. Plasma cutting of various metals and alloys is one of the most productive processes for obtaining workpieces, especially when using reverse polarity plasmatrons. The use of plasma cutting in the production of workpieces of large thicknesses potentially allows to increase the productivity of the process. In the domestic industry plasma cutting equipment of foreign production is widely used, which poses the problem of import substitution of manufactured products and equipment with the corresponding parts of Russian companies. For this reason, at present the Institute of Strength Physics and Materials Science together with the company "ITS Siberia" develops plasma cutting equipment on reverse polarity currents. At the same time, in order to determine the peculiarities of influence of parameters and modes of plasma cutting process on the structure of metal in the cutting zone, it is necessary to conduct comparative studies on different metals and alloys. Aim of the work: is to identify the characteristics of the influence of high energy impact on the structure and properties of surface layers of aluminum and titanium alloys during plasma cutting using a plasma torch operating with reverse polarity currents. The research methods are optical metallography, microhardness measurement and laser scanning microscopy of the surface after plasma cutting. Results and discussions. The conducted researches show a wide range of possibilities to adjust the process parameters of plasma cutting of aluminum alloys AA5056 and AA2124, and titanium alloy Grade2. For the alloys used in this work there are optimal values of process parameters, deviations from which lead to various violations of cut quality. Aluminum alloys show a tendency to significant de-strengthening in the cutting zone, which is associated with the formation of a large crystalline structure and large incoherent secondary phases with simultaneous depletion of the solid solution with alloying elements. Titanium alloys are characterized by quenching effects in the cutting zone with increasing microhardness values. Oxides are also formed in the surface layers despite the use of nitrogen shielding gas. In the alloy Ti-4Al-1Mn, in the previously conducted works, the formation of oxide films with high hardness is not noted, while in the Grade2 alloy at cutting in the surface layers oxides are formed sharply increasing the values of microhardness of the material up to values of about 15 GPa. This situation can complicate mechanical processing of titanium alloys after plasma cutting. The obtained results indicate a rather low value of the allowance for further machining after plasma cutting of aluminum and titanium alloys.

Detecting the influence of heat sources on material properties when producing aviation parts by a direct energy deposition method

Basic Research of Directed Energy Deposition for Aluminum 4043 Alloys Using Pulsed Variable Polarity Gas Metal Arc Welding

The influence of technological parameters on the structure formation of aluminum alloys during direct deposition of wire

Effects of Heat Input on Morphology of Thin‐Wall Components Fabricated by Wire and Arc Additive Manufacturing

A novel directed energy deposition-arc method of deposition layer without focused thermal energy heating: droplet transfer, morphology and microstructure

A Novel Heterogeneous Multi-Wire Indirect Arc Directed Energy Deposition for In-Situ Synthesis Al-Zn-Mg-Cu Alloy: Process, Microstructure and Mechanical Properties

Strength And Ductility Characteristics Of Metal Alloys And Stainless Steels Created By Wire-Arc Surfacing In A Wide Range Of Strain Rates

The effect of heat input on the microstructure and mechanical properties of 18Ni 300 maraging steel fabricated by arc directed energy deposition

EFFECT RESEARCH OF SURFACE DEFORMATION IMPACT AND THERMAL TREATMENT AT MULTI-LAYER WELD DEPOSITION UPON MECHANICAL PROPERTIES AND POROSITY OF ALUMINUM ALLOY 1580

Investigation of Mechanical Properties and Microstructure Analysis of 5356 Al Alloy Thin Plate and Block Fabricated by Directed Energy Deposition-Arc

Determining the influence of technological parameters of the electron-beam surfacing process on quality indicators

Analysis of thermal cycles during DED-Arc of high-strength low-alloy steel and microstructural evolution

Influence of oxygen content in the shielding gas chamber on mechanical properties and macroscopic structure of Ti-6Al-4V during wire arc additive manufacturing

Experimental Study on the Manufacturing of Steel Inclined Walls by Directed Energy Deposition Based on Dimensional and 3D Surface Roughness Measurements

Processing of Haynes® 282® Alloy by Direct Energy Deposition with Arc and Wire

The effect of direct energy deposition Arc mode on the porosity of AA5087 aluminium alloy

Influence of high-energy impact during plasma cutting on structure and properties of surface layers of aluminum and titanium alloys

Heat Source Modeling and Residual Stress Analysis for Metal Directed Energy Deposition Additive Manufacturing

Investigation on High-deposition-rate Directed Energy Deposition of Al-5%Mg Alloy Via External Compound Magnetic Fields

On the Effect of Heat Input and Interpass Temperature on the Performance of Inconel 625 Alloy Deposited Using Wire Arc Additive Manufacturing–Cold Metal Transfer Process

Study on Heat Input Effect of 316L Stainless Steel Thin-Walled Parts Processed by Wire Arc Additive Manufacturing