Abstract:The cubic $C$15 CaAl$_2$ Laves phase is a crucial brittle intermetallic precipitate in Mg-Al-Ca alloys. Although knowledge of the mechanical properties of coexisting phases is essential for improved alloy design, the fracture toughness is not yet studied experimentally due to the need for miniaturised testing. Here, micropillar splitting and microcantilever bending are used to experimentally determine the toughness of CaAl$_2$. It is found that the toughness value of ~1 $MPa\cdot\sqrt m$ from pillar splitting is largely insensitive to sample heat treatment, ion beam used for fabrication, micropillar diameter, and surface orientation. From nanoindentation supported by electron channelling contrast imaging and backscatter diffraction, fracture is observed to take place mostly on {011} planes. Atomistic fracture simulations on a model $C$15 Laves phase showed that the preference of {011} cleavage planes over the more energetically favourable {111} is due to lattice trapping and kinetics controlling fracture. Using rectangular microcantilever bending tests where the notch plane was misoriented to the closest possible {112} cleavage plane by ~8°, and the closest {001}, {011} and {111} plane by >20°, a toughness of ca. 2 $MPa\cdot\sqrt m$ was determined along with the electron microscopy observation of significant deviations of the crack path, demonstrating that preferential crystallographic cleavage planes determine the toughness in this material. Further investigation using pentagonal microcantilevers with precise alignment of the notch with the cleavage planes revealed similar fracture toughness values for different low-index planes. The results presented here are the first detailed experimental study of fracture toughness of the $C$15 CaAl$_2$ Laves phase, and can be understood in terms of crack plane and crack front dependent fracture toughness.

Local fracture toughness measurements in polycrystalline cubic zirconia using micro-cantilever bending tests

On the feasibility of the Chevron Notch Beam method to measure fracture toughness of fine-grained zirconia ceramics

Fracture Strength and Toughness of Chemical-Vapor-deposited Polycrystalline Diamond Films

Fracture Toughness of Advanced Structural Ceramics: Applying ASTM C1421

〈a〉 Prismatic, 〈a〉 basal, and 〈c+a〉 slip strengths of commercially pure Zr by micro-cantilever tests

Fracture Toughness Evaluation and Plastic Behavior Law of a Single Crystal Silicon Carbide by Nanoindentation

Hardness and fracture toughness of moissanite

In situ micro-cantilever tests to study fracture properties of NiAl single crystals

Accurate Comparison of the Fracture Toughness of Ultra-Thick Polycrystalline Diamond Plates by ISO Standard Method

Eliciting stable nanoscale fracture in single-crystal silicon

Micromechanical characterization of zirconia and silicon nitride ceramics using indentation and scratch methods

Assessing fracture toughness in sintered Al2O3–ZrO2(3Y)–SiC ceramic composites through indentation technique

Fracture behavior of lithia disilicate- and leucite-based ceramics

Porous LSCF/Dense 3YSZ Interface Fracture Toughness Measured by Single Cantilever Beam Wedge Test

Fracture Toughness Determination on an SCB Specimen by Meshless Methods

Reliable evaluation of fracture toughness in ceramics via nanosecond laser notching method

Accurate evaluation of critical flaw size in structural ceramics via femtosecond laser

Fracture of the $C$15 CaAl$_2$ Laves phase at small length-scales

Study of the Fracture Behavior of Tetragonal Zirconia Polycrystal with a Modified Phase Field Model

Evaluation of fracture toughness of zirconia silica nano-fibres reinforced feldespathic ceramic

Influence of grain‐scale microstructural parameters on fracture toughness of polycrystalline ceramics: Dual scale finite element method