Abstract:For reducing the emission of formaldehyde, urea formaldehyde (UF) resin adhesives used in the wood-based panel industry are mainly synthesized by adding urea in stages to reduce the molar ratio of formaldehyde and urea. Although the lower molar ratio UF resin has lower formaldehyde emissions, it also has the defects of longer curing time and lower bonding strength when being used in wood-based panel products. In this study, nanofluid type UF resins adhesives were prepared by dispersing SiO2 and TiO2 nanoparticles with six concentrations levels, 0%, 0.2%, 0.4%, 0.6%, 0.8% and 1% into UF resins with 1.0 and 1.3 M ratio by the assistance of ultrasound, respectively. It was found that the excellent thermal conductivity of the nanofluid type adhesives could eliminate the defects of the low molar ratio UF resins. When nano-SiO2 and nano-TiO2 were incorporated, the viscosity increased as the nanoparticles concentration increased, the maximum viscosity increased by 11.7% (1.0UF) and 15.0% (1.3UF) with nano-SiO2, the free formaldehyde content, curing time, and pot life of UF resins declined in varying degrees with nanoparticles loading level increased, the maximum amount of free formaldehyde content reduced by 41.2% (1.0UF) and 43.9% (1.3UF) with nano-TiO2, the maximum reduction of curing time was 25.80% (1.0UF) and 42.6% (1.3UF) with nano-TiO2, the pot life maximum decreased by 39.7% (1.0UF) and 43.0% (1.3UF) with nano-SiO2. Nanofluid type UF resins had much higher bonding strength with lower formaldehyde emission than pristine UF resins after being treated with same hot-pressing in plywood manufacture. The maximum of bonding strength increased by 28.1% (1.0UF) and 28.8% (1.3UF) with nano-SiO2, and the maximum amount of formaldehyde emissions reduced by 48.7% (1.0UF) with nano-SiO2 and 41.9% (1.3UF) with nano-TiO2. Meanwhile, the results showed that nanofluid type UF resin used in plywood manufacture exhibited the ability to decrease the hot-pressing temperature or shorten the hot-pressing time.

Incorporation of a nano/micro CuO formulation into phenol formaldehyde (PF) resin: Curing kinetics, morphological analysis, and application

Fabrication of nano-cupric oxide in phenol–formaldehyde resin adhesive: synthesis, curing characteristics, and morphology

The simultaneous preparation of nano cupric oxide (CuO) and phenol formaldehyde (PF) resin in one system: aimed to apply as wood adhesives

Effects of carbon fibers modification on the properties of unsaturated polyester self-healing composites

Behavior of epoxy resin filled with nano-SiO<sub>2</sub> treated with a Eugenol epoxy silane

Incorporation of In Situ Synthesized Nano-Copper Modified Phenol-Formaldehyde Resin to Improve the Mechanical Properties of Chinese Fir: A Preliminary Study

The characterizations of nanofluid type urea formaldehyde resins

Adhesion properties and formaldehyde emissions of MnO2/UF nanocomposite adhesives

Application of Nano-SiO2 Reinforced Urea-Formaldehyde Resin and Molecular Dynamics Simulation Study

Preparation of Cu/OMMT/LLDPE Nanocomposites and Synergistic Effect Study of Two Different Nano Materials in Polymer Matrix

Enhancement of mechanical and thermal properties of UV‐curable wood coatings by cellulose nanofibrils and carboxylated organo‐montmorillonite

Strategic moderation of thermal stability and curing time of lignin-based phenolic resin by incorporating nanoparticles

Combustion Assisted Synthesis of CuO Nanoparticles and Structure-Property Evaluation in nano-CuO Polymer Composites

A tough, strong, and fast-curing phenolic resin enabled by dopamine-grafted chitosan and polyethyleneimine-functionalized graphene

Curing dynamics and network formation of cyanate ester resin/polyhedral oligomeric silsesquioxane nanocomposites

Enhancing the performance of low molar ratio urea–formaldehyde resin adhesives via in-situ modification with intercalated nanoclay

Influence of Pressing Temperatures on Physical–Mechanical Properties of Wood Particleboards Made with Urea-Formaldehyde Adhesive Containing Al2O3 and CuO Nanoparticles

Synergistic effects of nanoparticle geometric shape and post curing on carbon-based nanoparticle reinforced epoxy coatings: Characterization, microstructure, and adhesion properties

Preparation of a nano-silica modified melamine formaldehyde resin

Enhanced curing process of eco-friendly oxidized cornstarch adhesive with Nano-CeO2

In-situ modification of low molar ratio urea–formaldehyde resins with cellulose nanofibrils for plywood