Natural rubber latex foam with particulate fillers for carbon dioxide adsorption and regeneration

Krittaya Panploo,Benjapon Chalermsinsuwan,Sirilux Poompradub

DOI: https://doi.org/10.1039/c9ra06000f

IF: 4.036

2019-01-01

RSC Advances

Abstract:To reduce the carbon dioxide (CO 2 ) concentration in the atmosphere, natural rubber (NR) was developed as a rubber foam for CO 2 adsorption.

chemistry, multidisciplinary

What problem does this paper attempt to address?

Effect of amine types and temperature of a natural rubber based composite material on the carbon dioxide capture

Krittaya Panploo,Benjapon Chalermsinsuwan,Sirilux Poompradub

DOI: https://doi.org/10.1016/j.cej.2020.125332

IF: 15.1

2020-12-01

Chemical Engineering Journal

Abstract:Solid natural rubber (NR) was chosen to prepare a carbon dioxide (CO2) adsorbent material in order to solve the disadvantage of using NR latex as the adsorbent. The effect of modifier type on the CO2 adsorption capacity of the NR/silica foam composites was investigated under ambient temperature and pressure. The CO2 adsorption capacity of the NR/silica foam composite material increased from 1.81 to 6.71 mg/g after filling with silica particles modified by 3-aminopropyltrimethoxysilane. The NR/silica foam composite material filled with silica particles modified with a short chain structure (3-aminopropyltrimethoxysilane) showed a higher CO2 adsorption capacity than those with a longer modifying chain structure (N-[(3-trimethoxysilyl)propyl]ethylenediamine or N-[(3-trimethoxysilyl)propyl]diethylenetriamine). The increasing of adsorption temperature caused the chains of the long-chain modifier on the silica particle surface to become more flexible, resulting in a high selectivity for capturing CO2. The NR/silica foam composite filled with unmodified or modified silica particles showed a high reusability compared to NR foam.

engineering, chemical, environmental
Enhanced Mechanical Properties of Natural Rubber by Block Copolymer-Based Porous Carbon Fibers

Wenqi Zhao,Zhen Xu,John Elliott,Cindy S. Barrera,Zacary L. Croft,Haibo Zhao,Janice Tardiff,Guoliang Liu

DOI: https://doi.org/10.1021/acsapm.1c01329

2021-01-01

ACS Applied Polymer Materials

Abstract:Nanosized particles have a large surface area to facilitate interfacial contact and thus are promising fillers for polymers. However, poor dispersion of nanoparticles limits the reinforcement effect. Herein, by rationally tailoring the internal porous structures, specific surface area, and surface chemistry, we prepared porous carbon fiber (PCF) filler from poly(acrylonitrile-block-methyl methacrylate) (PAN-b-PMMA) block copolymers. PCF had a three-dimensional porous network and provided improved filler-matrix interactions. Owing to the enhanced filler-matrix interlocking, large interfacial contact area, and strong interfacial affinity induced by nitrogen and oxygen doping, PCF was uniformly dispersed in rubber. Uncured nature rubber composites containing 5 parts of PCF per hundred parts of rubber (phr) showed 4.3 times higher Young's modulus and twice the tensile strength at 300% strain compared to the neat rubber. PCF represents an effective reinforcing filler for polymers.
Fabrication and properties of macrocellular modified natural rubber-poly (vinyl alcohol) foam for organic solvent/oil absorption

Sa-Ad Riyajan,Kanyapat Traitananan

DOI: https://doi.org/10.1016/j.indcrop.2020.112404

IF: 6.449

2020-10-01

Industrial Crops and Products

Abstract:A novel macroporous material was fabricated at ambient temperature from maleate epoxidized natural rubber (MENR), and poly (vinyl alcohol) (PVA), using modified cellulose (MC) as a cross-linker and blowing agent. The effects of differing MC contents on the physical properties, such as the moisture content, moisture absorption, swelling ratio, tensile strength, elongation at break and organic absorbency of solvents and oils of this novel macrocellular material were investigated. The density of the material was between 0.05 and 0.13 g/cm3 depending on the MC content. The optimal MC content was found to be 2%w/w which demonstrated the highest moisture content and moisture absorption due to the highly porous structure of the foam produced. The foams were applied as organic absorbents for solvents and oils and the highest adsorption capacities of approximately 9.0, 11.5, 12.0, 11.5, 12.0, and 14.0 g/g for methanol, toluene, gasohol, diesel, kerosene and petroleum respectively were produced by the blend containing 2 %w/w MC. Moreover, the material was found to be reusable as an absorbent over 30 absorption-squeeze cycles. The materials were also found to naturally degrade when buried in soil and would not therefore cause environmental pollution.

agronomy,agricultural engineering
Resorcinol–formaldehyde Resin-Based Porous Carbon Spheres with High CO2 Capture Capacities

Xuan Wang,Jin Zhou,Wei Xing,Boyu Liu,Jianlin Zhang,Hongtao Lin,Hongyou Cui,Shuping Zhuo

DOI: https://doi.org/10.1016/j.jechem.2017.07.010

2017-01-01

Abstract:Porous carbon spheres are prepared by direct carbonization of potassium salt of resorcinol-formaldehyde resin spheres, and are investigated as CO2 adsorbents. It is found that the prepared carbon materials still maintain the typical spherical shapes after the activation, and have highly developed ultra-microporosity with uniform pore size, indicating that almost the activation takes place in the interior of the polymer spheres. The narrow-distributed ultra-micropores are attributed to the "in-situ homogeneous activation" effect produced by the mono-dispersed potassium ions as a form of -OK groups in the bulk of polymer spheres. The CS-1 sample prepared under a KOH/resins weight ratio of 1 shows a very high CO2 capture capacity of 4.83 mmol/g and good CO2/N-2 selectivity of similar to 17-45. We believe that the presence of a welldeveloped ultra-microporosity is responsible for excellent CO2 sorption performance at room temperature and ambient pressure. (C) 2017 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.
Porous Cellulose Nanofibril–Natural Rubber Latex Composite Foams for Oil and Organic Solvent Absorption

Marcos V. Lorevice,Eduardo O. Mendonça,Naíma M. Orra,Antonio C. Borges,Rubia F. Gouveia,Eduardo O. Mendonça,Naíma M. Orra

DOI: https://doi.org/10.1021/acsanm.0c02203

IF: 6.14

2020-10-14

ACS Applied Nano Materials

Abstract:Nanocellulose-based foams are widely used as absorbents due to their highly porous networks and large surface areas. However, their inherent hydrophilicity and poor wet resilience limit their applications in water remediation for the removal of hydrophobic components (e.g., oil and organic solvent spills). A straightforward process combining biomass-derived materials, cellulose nanofibrils (CNFs), and natural rubber (NR) latex, in the absence of any organic solvent, is herein elucidated to design eco-friendly hydrophobic foams. NR acts as an anchoring filler within the CNF three-dimensional (3D) network, tailoring the production of CNF foams with tunable morphologies, interconnected walls, specific surface areas (∼226 m2·g–1), and higher porosities (more than 92%). Aqueous NR and CNF dispersion exhibited great colloidal stability (ζ-potential above −30 mV), a desirable characteristic to obtain controlled structures. The spherical shape of NR (diameter of ca. 500 nm) and the fibrous morphology of CNF, both by themselves and when mixed, were evidenced by cryogenic transmission electron microscopy. The porous architecture built up through ice templating was corroborated by scanning electron microscopy and 3D X-ray microtomography (μCT). The CNF 3D network and NR promoted rigid and robust foams with elevated compressive modulus (∼600 kPa, for NR20/CNF80). In situ four-dimensional (4D) μCT revealed an impressive increase in oil uptake—from 44 ± 5 to 90 ± 7%—by foam pores upon NR addition. NR was demonstrated by pore segmentation to be evenly distributed throughout the CNF surface, awarding great hydrophobicity (apparent contact angle of around 100°), excellent and quick oil/organic solvent absorption (above 50 g·g–1 in 3 s), and excellent reusability (20 cycles) for organic solvents and oils. This green material exhibits great capacity of soaking nonpolar molecules, standing out as an environmentally friendly, cost-effective, and promising alternative for water cleanup.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsanm.0c02203?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsanm.0c02203</a>.SEM images, supplementary morphometric analysis, mechanical attributes for pristine CNF foams, absorption capacity data, structural resistance in organic solvents, complementary data reusability tests, reusability tests of NR20/CNF80 in the diesel oil/water mixture, statistical data of water contact angles, specific surface areas obtained by the methylene blue adsorption test, complementary scheme of the ice-templating process and coating/cross-linking of NR/CNF foams, adhesion assays by force–distance curves, complementary spectroscopy analysis, and cellulose composition (<a class="ext-link" href="/doi/suppl/10.1021/acsanm.0c02203/suppl_file/an0c02203_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

materials science, multidisciplinary,nanoscience & nanotechnology
The Relationship between the Morphology and Elasticity of Natural Rubber Foam Based on the Concentration of the Chemical Blowing Agent

Supitta Suethao,Saree Phongphanphanee,Jirasak Wong-ekkabut,Wirasak Smitthipong

DOI: https://doi.org/10.3390/polym13071091

IF: 5

2021-03-30

Polymers

Abstract:Concentrated natural latex was used to produce a rubber foam that is porous, elastic and well ventilated. The mechanical properties can be either soft or firm, depending on the formulation of the latex used. Briefly, concentrated natural latex was mixed with chemical agents to make the rubber foam on a laboratory scale using the Dunlop process. In this work, we changed the concentration of the chemical blowing agent in the latex. The morphological properties of the rubber foam were characterised using scanning electron microscopy, and the mechanical properties, or elasticity, were studied using compression experiments and the Mooney–Rivlin calculation. The results show that the concentration of the chemical blowing agent affects the morphological properties of the rubber foam but not the mechanical properties, indicating the heterogeneous structure of the rubber foam. The thermodynamic parameters (∆G and ∆S) and the internal energy force per compression force (Fu/F) of the rubber foam with various amounts of chemical blowing agent were also investigated. This study could be applied in the foam industry, particularly for pillow, mattress and insulation materials, as the present work shows the possible novel control of the morphological structure of the rubber foam without changing its mechanical properties. The difference in cell sizes could affect the airflow in rubber foam.

polymer science
Engineering Porous Organic Polymers for Carbon Dioxide Capture

Ning Huang,Gregory Day,Xinyu Yang,Hannah Drake,Hong-Cai Zhou

DOI: https://doi.org/10.1007/s11426-017-9084-7

2017-01-01

Science China Chemistry

Abstract:As atmospheric CO 2 levels rise, the development of physical or chemical adsorbents for CO 2 capture and separation is of great importance on the way towards a sustainable low-carbon future. Porous organic polymers are promising candidates for CO 2 capture materials owing to their structural flexibility, high surface area, and high stability. In this review, we highlight high-performance porous organic polymers for CO 2 capture and summarize the strategies to enhance CO 2 uptake and selectivity, such as increasing surface area, increasing interaction between porous organic polymers and CO 2 , and pore surface functionalization.
Research Progress of Adsorbents for Carbon Dioxide

Zhirong Liu

2012-01-01

Abstract:The main carbon dioxide adsorbents over domestic and overseas,such as cellular materials,metal oxide,hydrotalcite-like compounds and salts adsorbents,are described.The adsorption property,influencing factor,and advantages and disadvantages are introduced.The development direction of carbon adsorbents is prospected,too.
Enhanced CO2 capturing over ultra-microporous carbon with nitrogen-active species prepared using one-step carbonization of polybenzoxazine for a sustainable environment

Nicharat Manmuanpom,Uthen Thubsuang,Stephan Thierry Dubas,Sujitra Wongkasemjit,Thanyalak Chaisuwan

DOI: https://doi.org/10.1016/j.jenvman.2018.07.004

2018-10-01

Abstract:Nitrogen-enriched porous carbon has been a promising material for CO2 capture in the recent decades. To enhance the performance of CO2 adsorption, both an N-active site and the textural properties are crucial determinants. Herein, ultra-microporous carbon with N-active species was prepared using two synthesis procedures: 1) one-step carbonization of a polybenzoxazine (PBZ) precursor at 800 °C, and 2) the CO2 activation process at 900 °C. The activated porous carbon had the higher specific surface area (943 m2/g) and a total pore volume (0.51 cm3/g) compared to un-activated porous carbon (335 m2/g and 0.19 cm3/g, respectively). In addition, the presence of N-active species such as pyridine-N, secondary-N, pyridone-N, and oxide-N in the carbon structures could be clearly observed in the high-resolution XPS spectra. The CO2 adsorption measurement was performed at 30 and 50 °C under a wide range of pressures (1-7 bar). The maximum amount of CO2 uptake was ca. 3.59 mmol/g for the activated porous carbon operated at 30 °C and a CO2 pressure of 7 bar, which was due to the high specific surface area and the large micropore volume. Specifically, carbon with a 3D interconnected pore structure, derived from the sol-gel process of the PBZ precursor, exhibited good structural stability and consequently led to better absorption capability under the high atmospheric pressure of CO2. The enhanced CO2 adsorption capability for the as-prepared porous carbon was based on two mechanisms: physisorption as a result of textural properties and chemisorption as a result of the acid-base interaction between the basic N functionality and the acidic CO2 gas. All results suggested that ultra-microporous carbon with N-active species prepared from polybenzoxazine is a promising adsorbent for CO2 capture and storage, which can be used at a wide range of pressures and in many applications e.g. flue gas adsorption and natural gas production.
Foamability of Natural rubber (NR)/Poly(butylenes adipate-co-terephthalate) (PBAT) Thermoplastic Vulcanizate with OBSH as a blowing agent

J Srikham,C Thongpin

DOI: https://doi.org/10.1088/1757-899X/965/1/012018

2020-12-23

IOP Conference Series: Materials Science and Engineering

Abstract:Natural rubber, NR, is bio-based material that is generally used for foam preparation as it results in good softness and high resilience. Among many applications, NR foam/sponge is often used for shoe sole either insole or outsole. Likewise, rubber sponge is very important for healing Plantar Fasciitis as rubber sponge is soft, elastic and capable in impact absorption. NR is in fact non-biodegradable resulting in increasing of waste which is a hot issue at present. Huge interest has paid attention in using biodegradable polymer in various products and applications. Polybutylene adipate-co-terephthalate, PBAT, is one of many bioplastics that possesses biodegradability characteristic. It also shows excellent flexibility similar to elastomer. Many attempts have been focus on blending this polymer to improve toughness in brittle plastic. Our research is aimed to incorporate PBAT into NR and producing thermoplastic vulcanizate. NR/PBAT TPV foam is then produced using 4,4-'Oxybis-benzenesulfonyl hydrazide (OBSH) as a blowing agent. The ratios of NR/PBAT are varied as follow: 70/30 65/35 60/40 55/45 50/50 45/55. The polymer blends were mixed on a two-roll mill with the formulation of ZnO 3 phr, luperox 101 1 phr and OBSH 10 phr. Compression molding was used in order to prepare rubber sponge at 160 °C, 1500 psi. Cell size, cell size distribution, density and compression set of NR/PBAT foam were investigated.
Chemically activated carbon preparation from natural rubber biosludge for the study of characterization, kinetics and isotherms, thermodynamics, reusability during Cr(VI) and methylene blue adsorption

Uttara Mahapatra,Abhijit Chatterjee,Chandan Das,Ajay Kumar Manna

DOI: https://doi.org/10.2166/wst.2023.004

Abstract:Alkaline leachate, dust generation, and foul smell during the stacking process of natural rubber biosludge (NRBS) can pollute surrounding water, soil, and air. In this study, natural rubber chemically activated carbon (NRCAC) has been synthesized for the first time from NRBS by pyrolysis using ZnCl2 at 700 °C for adsorptive removal of Cr(VI) and methylene blue (MB) from aqueous solutions. Both NRBS and NRCAC were characterized by X-ray fluorescence (XRF), X-ray diffraction (XRD), Fourier transform infrared (FTIR), scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS), Brunauer-Emmett-Teller (BET), and thermogravimetric analyzer (TGA). FTIR and SEM-EDS suggested significant functional and morphological transformations in NRCAC. Experimental investigations of different process parameters, such as pH, concentration, contact time, salt concentration, etc., were conducted to study their influences on adsorption. Adsorption and desorption kinetics followed a pseudo-second-order model, while adsorption equilibrium followed Liu isotherm. Maximum uptake calculated from the Liu model was 81.28 and 211.90 mg/g for Cr(VI) and MB, respectively. Thermodynamic analysis established spontaneous and endothermic adsorption. Up to five adsorption/desorption cycles were conducted using eluents such as 1 M NaOH and water for Cr(VI) and MB, respectively. Electrostatic attraction and ion-exchange favored Cr(VI)/MB adsorption, while hydrogen bonding and π-π stacking were significant in MB uptake. Overall findings suggest that NRBS (a renewable agro-industrial, abundant, and freely available) could be employed to synthesize biochar for adsorptive removal of wastewater containing Cr(VI)/MB.
A Soluble and Recyclable Polymeric Adsorbent of Intrinsic Microporosity for CO2 Capture

X. Wang,P. Ma,Y.J. Jing,C. Yu,H. Qiu,C. Kang,Z. Cui,K. Hou,A.C.K. Yip,B.H. Yin,Xinbo Wang,Pengcheng Ma,YuanJu Jing,Cong Yu,Hao Qiu,Chun Kang,Zhaojie Cui,Keyong Hou,Alex C.K. Yip,Ben Hang Yin

DOI: https://doi.org/10.1016/j.mtsust.2023.100484

IF: 7.244

2023-07-01

Materials Today Sustainability

Abstract:Excessive emission of greenhouse gases has caused global warming and been seriously damaging the ecological environment. Adsorption technology is one of the most powerful methods widely used for carbon capture. However, the currently available rigid porous adsorbents are all insoluble, the regeneration of which once blocked is a quandary. In this study, we synthesized a soluble polymeric adsorbent of intrinsic microporosity (AO-PIM-1) for carbon dioxide (CO2) capture. The adsorbent of AO-PIM-1, an amidoxime functionalized PIM-1, possesses a high-specific surface area of 503 m2/g and a strong affinity for CO2 with the heat of adsorption of 30.6 kJ/mol. It exhibits high CO2 adsorption capacity and CO2/N2 selectivity evidenced by computational calculations and experimental breakthrough experiments. More importantly, the microporous AO-PIM-1 is well soluble in common organic solvents like DMF, DMSO, and DMAc, but insoluble in methanol, which allows the regeneration, once being fouled, with a solvent dissolution-separation purification-nonsolvent-induced precipitation (DSP) method.

materials science, multidisciplinary,green & sustainable science & technology
Robust Nitrogen-Doped Microporous Carbon via Crown Ether-Functionalized Benzoxazine-Linked Porous Organic Polymers for Enhanced CO2 Adsorption and Supercapacitor Applications

Mohamed Gamal Mohamed,Bo-Xuan Su,Shiao-Wei Kuo

DOI: https://doi.org/10.1021/acsami.4c05645

2024-08-07

Abstract:Nitrogen-doped carbon materials, characterized by abundant microporous and nitrogen functionalities, exhibit significant potential for carbon dioxide capture and supercapacitors. In this study, a class of porous organic polymer (POP) were successfully synthesized by linking Cr-TPA-4BZ-Br4 and tetraethynylpyrene (Py-T). The model benzoxazine monomers of Cr-TPA-4BZ and Cr-TPA-4BZ-Br4 were synthesized using the traditional three-step method [involving CH═N formation, reduction by NaBH4, and Mannich condensation]. Subsequently, the Sonogashira coupling reaction connected the Cr-TPA-4BZ-Br4 and Py-T monomers, forming Cr-TPA-4BZ-Py-POP. The successful synthesis of Cr-TPA-4BZ-Br4 and Cr-TPA-4BZ-Py-POP was confirmed through various analytical techniques. After verifying the successful synthesis of Cr-TPA-4BZ-Py-POP, carbonization and KOH activation procedures were conducted. These crucial steps led to the formation of poly(Cr-TPA-4BZ-Py-POP)-800, a carbon material with a structure akin to graphite. In practical applications, poly(Cr-TPA-4BZ-Py-POP)-800 exhibited a noteworthy CO2 adsorption capacity of 4.4 mmol/g, along with specific capacitance values of 397.2 and 159.2 F g-1 at 0.5 A g-1 (measured in a three-electrode cell) and 1 A g-1 (measured in a symmetric coin cell), respectively. These exceptional dual capabilities stem from the optimal ratio of heteroatom doping. The outstanding performance of poly(Cr-TPA-4BZ-Py-POP)-800 microporous carbon holds significant promise for addressing contemporary energy and environmental challenges, making substantial contributions to both sectors.
Pore Structure Characteristics of Foam Composite with Active Carbon

Jungsoo Lee,Young Cheol Choi

DOI: https://doi.org/10.3390/ma13184038

IF: 3.4

2020-09-11

Materials

Abstract:Characterization of porous materials is essential for predicting and modeling their adsorption performance, strength, and durability. However, studies on the optimization of the pore structure to efficiently remove pollutants in the atmosphere by physical adsorption of construction materials have been insufficient. This study investigated the pore structure characteristics of foam composites. Porous foam composites were fabricated using foam composite with high porosity, open pores, and palm shell active carbon with micropores. The content was substituted 5%, 10%, 15%, and 20% by volume of cement. From the measured nitrogen adsorption isotherm, the pore structure of the foam composite was analyzed using the Brunauer–Emmett–Teller (BET) theory, Barrett–Joyner–Halenda (BJH) analysis, and Harkins-jura adsorption isotherms. From the analysis results, it was found that activated carbon increases the specific surface area and micropore volume of the foam composite. The specific surface area and micropore volume of the foam composite containing 15% activated carbon were 106.48 m2/g and 29.80 cm3/g, respectively, which were the highest values obtained in this study. A foam composite with a high micropore volume was found to be effective for the adsorption of air pollutants.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Preparation of high-quality wollastonite/natural rubber composites by atomization sputtering rapid drying process

Yao Xiao,Lizhi Yan,Tianhao Chang,Yingjie Hao,Yanjun Sui,Huiguang Bian,Chuansheng Wang,Xiaoming Wang

DOI: https://doi.org/10.1007/s00289-022-04298-9

IF: 2.843

2022-07-13

Polymer Bulletin

Abstract:Nano-fumed silica has small primary particle size and high surface energy, which leads to serious adsorption agglomeration in rubber, and the corrosive gases such as hydrogen chloride produced in the production process endanger the environment. In the present study, wollastonite was introduced as an environmentally friendly and low-cost natural mineral into the natural rubber system. Wollastonite achieved the effect of reinforcing and relieving stress concentration with its own high stiffness and fibrous structure. Additionally, the water dispersion system of wollastonite was more stable. Owing to gas-phase-assisted atomization sputtering and high-temperature rapid drying, the secondary aggregates of the fillers were broken up effectively, and wollastonite fibers were highly dispersed in natural rubber latex. The obtained experimental results showed that replacing fumed silica with wollastonite in the same amount could improve the processability of rubber and reduce the rolling resistance. Compared with dry mixing, the tensile strength and tensile product of the wollastonite/NR composites prepared by atomization sputtering rapid drying process were increased by 8 and 25%, and the compression fatigue temperature rise of rubber surface was reduced by 29%. The study realized energy conservation, environmental protection and low cost.Graphical abstract

polymer science
Nickle oxide nanoparticles incorporated flexible and porous carbon nanofiber-based adsorbents for CO 2 capture

Nadir Ali,Taimoor Hussain,Xianfeng Wang,Jianyong Yu,Bin Ding

DOI: https://doi.org/10.1016/j.coco.2023.101604

IF: 8

2023-05-06

Composites Communications

Abstract:To capture carbon dioxide (CO 2 ) from the environment, carbonaceous materials are thought to be a convenient source. However, introducing flexibility with high porosity into the carbon nanofibers stays a demanding task. Herein, NiO nanoparticles (NPs) incorporated flexible and porous carbon nanofibers were created using an electrospinning process and subsequent carbonization treatment. The optimized (NiC-3) membranes demonstrated superior CO 2 adsorption capacity of 2.5 mmol g −1 at 25 °C, strong CO 2 gas selectivity (S=20) compared to N 2 gas, and incredible cyclic stability. After 10 adsorption-desorption cycles, no major mass change was observed, and the CO 2 uptake performance retains >95% of the initial value unveiling the high stability and practical importance of as-synthesized NiC-3 membrane. The incorporation of NiO NPs in the carbon framework not only improved the surface area, porosity, and vacant oxygen sites to capture CO 2 molecules but also enhances the flexibility of the CNFs by acting as a plasticiser for single-fibre-crack connection. Profoundly, NiO NPs incorporated porous and flexible CNFs are a good choice for CO 2 adsorption applications due to their excellent structural stability, which overcomes the restrictions of annihilation and failure of structure for conventional adsorbents.

materials science, composites
Maximizing Ether Oxygen Content in Polymers for Membrane CO2 Removal from Natural Gas.

Junyi Liu,Gengyi Zhang,Krysta Clark,Haiqing Lin

DOI: https://doi.org/10.1021/acsami.9b01079

IF: 9.5

2019-01-01

ACS Applied Materials & Interfaces

Abstract:Membrane materials for CO2 removal from natural gas are based on glassy polymers with a high CO2/CH4 diffusivity selectivity. However, these polymers suffer from competitive sorption by heavy hydrocarbons that decreases CO2 permeability and physical aging that reduces gas permeability with time. We circumvent these issues by designing rubbery, solubility-selective polymers with a ratio of ether/ester oxygen to carbon as high as 0.8 through the use of 1,3-dioxolane and 1,3,5-trioxane. The ether/ester oxygen groups interact favorably with CO2 but do not interact with CH4, leading to a high CO2/gas solubility selectivity that is unaffected by heavy hydrocarbons in the raw natural gas. These polar groups are incorporated in short branches to yield an amorphous and rubbery nature, leading to high gas permeability that is stable over time. A polymer with an O/C ratio of 0.71 (P71) shows a mixed-gas CO2 permeability of 320 Barrers and a CO2/CH4 selectivity of 21 in the simulated natural gas at 50 °C, which is independent of the hexane content and above the upper bound for CO2/CH4 separation at 50 °C.
Effect of inorganic fillers on natural rubber latex foam vulcanisates

Shera Mathew,K. M. Malu,Siby Varghese,Parvathy S. Kumar,N. Vaishak

DOI: https://doi.org/10.1007/s42464-024-00240-y

2024-02-27

Journal of Rubber Research

Abstract:The focus of this study is on the evaluation of the effect of different types of inorganic fillers on the different major properties of natural rubber latex (NRL) foam vulcanisates. The mechanical and chemical properties of filled NRL foam were evaluated and compared with unfilled vulcanisate as per BIS standards IS 1741:2019 and IS: 6664 (1992) RA 2004 specification. The different fillers at various loadings selected for this study were marble powder, talc and China clay. From this study, talc was found to impart good mechanical properties such as indentation hardness index, flexing properties, compression set at constant strain and stress and split tear strength. It was also found that the chemical properties such as ageing resistance and water absorption properties for talc-filled foam were found to be equivalent to NRL foam without filler. Amongst the fillers studied talc possesses better mechanical and chemical properties followed by marble powder and China clay. Scanning electron microscope (SEM) image analysis of NRL foam at 500 μm scale with talc is self-explanatory to the above-mentioned facts.

polymer science
Wormwood-infused porous-CaCO3 for synthesizing antibacterial natural rubber latex

Xi Chen,JiaQi Zheng,LinXin You,Tian Qiu,Tyler Christoforo,Yen Wei

DOI: https://doi.org/10.1016/j.ijbiomac.2024.129322

Abstract:Wormwood leaf is a traditional Chinese herbal medicine with a high medicinal value and long application history and its essential oil is a high-purity plant oil extracted from Wormwood leaf. Pharmacological research reveals that Wormwood leaf and Wormwood essential oil are a broad-spectrum antibacterial and antiviral drug, which can inhibit and kill many bacteria and viruses. We loaded wormwood extract on porous calcium carbonate (Porous-CaCO3) and introduced it and Wormwood essential oil into Natural rubber latex (NRL), thus synthesizing NRL composites with excellent vitro and in vivo antibacterial effect, cell compatibility and mechanical properties. This NRL material can delay the light aging and thermal oxidation of some mechanical properties, which provides a broader avenue for its commercialization.
Potent Application of Scrap from the Modified Natural Rubber Production as Oil Absorbent

Anoma Thitithammawong,Sitisaiyidah Saiwari,Subhan Salaeh,Nabil Hayeemasae

DOI: https://doi.org/10.3390/polym14235066

2022-11-22

Abstract:The production of raw natural rubber always ends up with leftover latex. This latex is later collected to produce low grades of rubber. The collection of this latex also depends on the latex's quality. However, reproducing the latex may not be applicable if the latex contains many specks of dirt which will eventually be discarded. In this work, an alternative solution was to utilize such rubber in a processable form. This scrap rubber (SR) from the production of natural rubber grafted with polymethyl methacrylate (NR-g-PMMA) production was recovered to prepare an oil-swellable rubber. The rubber blends were turned into cellular structures to increase the oil swellability. To find the suitable formulation and cellular structure of the foam, the foams were prepared by blending SR with virgin natural rubber (NR) at various ratios, namely 0/100, 20/80, 30/70, 50/50, 70/30, 80/20, and 100/0 (phr/phr). The foam formation strongly depended on the SR, as it prevented gas penetration throughout the matrix. Consequently, small cells and thick cell walls were observed. This structure reduced the oil swellability from 7.09 g/g to 5.02 g/g. However, it is interesting to highlight that the thermal stability of the foam increased over the addition of SR, which is likely due to the higher thermal stability of the NR-g-PMMA waste or SR. In summary, the blending NR with 30 phr of SR provided good oil swellability, processability, and morphology, which benefit oil recovery application. The results obtained from this study will be used for further experiments on the enhancement of oil absorbency by applying other key factors. This work is considered a good initiative for preparing the oil-absorbent material based on scrap from modified natural rubber production.

Natural rubber latex foam with particulate fillers for carbon dioxide adsorption and regeneration

Effect of amine types and temperature of a natural rubber based composite material on the carbon dioxide capture

Enhanced Mechanical Properties of Natural Rubber by Block Copolymer-Based Porous Carbon Fibers

Fabrication and properties of macrocellular modified natural rubber-poly (vinyl alcohol) foam for organic solvent/oil absorption

Resorcinol–formaldehyde Resin-Based Porous Carbon Spheres with High CO2 Capture Capacities

Porous Cellulose Nanofibril–Natural Rubber Latex Composite Foams for Oil and Organic Solvent Absorption

The Relationship between the Morphology and Elasticity of Natural Rubber Foam Based on the Concentration of the Chemical Blowing Agent

Engineering Porous Organic Polymers for Carbon Dioxide Capture

Research Progress of Adsorbents for Carbon Dioxide

Enhanced CO2 capturing over ultra-microporous carbon with nitrogen-active species prepared using one-step carbonization of polybenzoxazine for a sustainable environment

Foamability of Natural rubber (NR)/Poly(butylenes adipate-co-terephthalate) (PBAT) Thermoplastic Vulcanizate with OBSH as a blowing agent

Chemically activated carbon preparation from natural rubber biosludge for the study of characterization, kinetics and isotherms, thermodynamics, reusability during Cr(VI) and methylene blue adsorption

A Soluble and Recyclable Polymeric Adsorbent of Intrinsic Microporosity for CO2 Capture

Robust Nitrogen-Doped Microporous Carbon via Crown Ether-Functionalized Benzoxazine-Linked Porous Organic Polymers for Enhanced CO2 Adsorption and Supercapacitor Applications

Pore Structure Characteristics of Foam Composite with Active Carbon

Preparation of high-quality wollastonite/natural rubber composites by atomization sputtering rapid drying process

Nickle oxide nanoparticles incorporated flexible and porous carbon nanofiber-based adsorbents for CO 2 capture

Maximizing Ether Oxygen Content in Polymers for Membrane CO2 Removal from Natural Gas.

Effect of inorganic fillers on natural rubber latex foam vulcanisates

Wormwood-infused porous-CaCO3 for synthesizing antibacterial natural rubber latex

Potent Application of Scrap from the Modified Natural Rubber Production as Oil Absorbent