Abstract:The prospect of blending gasoline fuel with ethanol is being investigated as a potential way to improve the knock residence of the base gasoline. However, one of the drawbacks is a lack of proper understanding of the reason for the non-linear response of blending ethanol and gasoline. This non-linearity could be better understood by an improved knowledge of the interactions of these fuel components at a molecular level. This study proposed a highly reduced four-component (toluene/n-heptane/iso-octane/ethanol) gasoline surrogate model containing 59 species and 270 reactions. The model was reduced using the direct relation graph with expert knowledge (DRG-X) (Lu and Law, 20015; Lu et al., 2011) and isomer lumping method. The computational singular perturbation (CSP) analysis were performed to reduce the potential stiffness issues by accordingly adjusting the Arrhenius coefficients of the proper reactions. The model has been comprehensively validated against wide range of ignition delay times (IDT) and flame speed (FS) measurement data as well as compared against two representative literature models from Liu et al. (2013) and Wang et al. (2015). Overall, good agreements were observed between model predictions and experimental data across the entire research octane number (RON), equivalence ratio, pressure and temperature range. In addition, the model has also been coupled with the computational fluid dynamic (CFD) models to simulate the experimental data of constant volume reacting spray of a low-octane gasoline (Haltermann straight-run naphtha), and in-cylinder pressures and temperatures of a high-octane gasoline (Haltermann Gasoline) combustion in a heavy duty compression ignition engine. The coupled model can qualitatively predict the experimentally obtained data with an improved performance for PRF, TPRF, and TPRF-ethanol surrogates.

A Multi-Response Optimization for Isomerization of light Naphtha

Multiobjective Optimization of the Industrial Naphtha Catalytic Reforming Process

Simulation, sensitivity analysis and optimization of a continuous catalytic reforming process

Modeling, Simulation and Optimization of Commercial Naphtha Catalytic Reforming Process

Modeling, Simulation and Optimization of a Whole Industrial Catalytic Naphtha Reforming Process on Aspen Plus Platform

Molecular Modeling and Optimization for Catalytic Reforming

Optimizing Naphtha Utilization Based on Molecular Scale Management

Integrated Dual-Production Mode Modeling and Multiobjective Optimization of an Industrial Continuous Catalytic Naphtha Reforming Process

Operation parameters effect on yield and octane number for monometallic, bimetallic and trimetallic catalysts in naphtha reforming process

Development of a Reduced Four-Component (Toluene/n-Heptane/iso-octane/ethanol) Gasoline Surrogate Model

Experimental optimization and reactor simulation of coal-derived naphtha reforming over Pt–Re/γ-Al 2 O 3 using design of experiment and response surface methodology

Hydroisomerization of Iraqi Light Naphtha Over the Prepared Pt/HY Catalyst to Produce High-Quality Fuel

Optimization Using Response Surface Methodology and Kinetic Study of Fischer–Tropsch Synthesis Using SiO2 Supported Bimetallic Co–Ni Catalyst

Multicriteria optimization of gasoline catalytic reforming temperature regime based on a kinetic model with grouped hydrocarbons

Pyrolysis and oxidation of a light naphtha fuel and its surrogate blend

Multi-Zone Conversion for the Maximizing Production of Btx from Naphtha

Study of Modification and Performance of HZSM-5 Catalyst for Isomerization of Light Paraffin

Optimized Utilization of Naphtha: Liquid Adsorption Separation of Linear Paraffins in Naphtha with N-Pentane As the Desorbent

Modelling Industrial Catalytic Reforming of Lowoctane Gasoline

Reaction Mechanism and Kinetic Modeling of Hydroisomerization and Hydroaromatization of Fluid Catalytic Cracking Naphtha

Simulation and optimization on etherification of light gasoline in a process of two fixed-bed reactors and one distillation column