Abstract:In the present study, the models of flow, heat transfer and reforming of 2-D single reforming tube and 3-D reformer core inside the reformer were implemented by CFD. The models were evaluated by comparison of simulations with data derived from a catalytic packed-bed reactor. In addition, a NG engine-reformer experimental system was established. Thereby, the experimental studies on performance of the reformer and engine under different excess air coefficient (λ), exhaust gas recirculation rate (XEGR) and reformed NG supply (CH4/O2, M/O value) were conducted based on IMO Tier III and China II emission standards. The results showed that oxidation and steam reforming reactions of methane were dominant in the process of exhaust gas-methane reforming and had obvious reaction sequence. For the reformer optimization, the design parameters were determined: GHSV = 16,000 h-1 and L/D = 7 for single reforming tube; diffuse angle of 30° and one deflector for reformer core. Besides, for experiments of REGR system, the reformer should operate under the condition of near M/O = 2-2.5 and XEGR = 7.3 % with high λ to achieve an optimal H2 yield and efficient H2 production. Compared with original engine under 50 % load and XEGR = 10.4 %, the brake thermal efficiency of the engine with REGR was increased by the maximum of 0.7 % (λ = 1.31). Noted that the maximum 85.5 % reduction of HC + NOx and the minimum 64.1 % treatment rate of CH4 could be obtained for meeting China II at λ = 1.25. Under different propeller loads, HC + NOx and CO emissions could both satisfy IMO Tier III and China II standards via adjusting the matched strategy of λ and XEGR. To meet fully China II standard, the minimum treatment rate of CH4 by the post-treatment unit needed to reach 79 %, 64 % and 64 % at 25 %, 50 % and 75 % load, respectively.

Experimental optimization and reactor simulation of coal-derived naphtha reforming over Pt–Re/γ-Al 2 O 3 using design of experiment and response surface methodology

Simulation, sensitivity analysis and optimization of a continuous catalytic reforming process

Modeling, Simulation and Optimization of Commercial Naphtha Catalytic Reforming Process

Modeling, Simulation and Optimization of a Whole Industrial Catalytic Naphtha Reforming Process on Aspen Plus Platform

Lumped Kinetics Model and Its On-Line Application to Commercial Catalytic Naphtha Reforming Process

Multiobjective Optimization of the Industrial Naphtha Catalytic Reforming Process

A dynamic model for naphtha catalytic reformers

The Coupling Performance During Reactive Sorption Enhanced Reforming (reser) Process: Simulation and Experimental Studies

Modeling and Simulation of Commercial Catalytic Reformers

Modeling and Optimization of Ethane Steam Cracking Process in An Industrial Tubular Reactor with Improved Reaction Scheme

Molecular Modeling and Optimization for Catalytic Reforming

Numerical Simulation and Experimental Study on Commercial Diesel Reforming over an Advanced Pt/Rh Three-Way Catalyst

Numerical Simulation and Experimental Investigation of Diesel Fuel Reforming over a Pt / CeO 2-Al 2 O 3 Catalyst

Operation parameters effect on yield and octane number for monometallic, bimetallic and trimetallic catalysts in naphtha reforming process

Optimization of the Countercurrent Continuous Reforming Process Based on Equation-Oriented Modeling and the SQP Algorithm

Simulative Optimization of Catalyst Configuration for Biogas Dry Reforming

Modelling Industrial Catalytic Reforming of Lowoctane Gasoline

Design, optimization and application of reformer in a marine natural gas engine: A numerical and experimental study

Modeling and Design of a Multi-Tubular Packed-Bed Reactor for Methanol Steam Reforming over a Cu/ZnO/Al2O3 Catalyst

Research on the Optimization of the Operating Parameters of Methane Carbon Dioxide Reforming Using the Response Surface Methodology

Catalytic-Level Identification of Prepared Pt/HY, Pt-Zn/HY, and Pt-Rh/HY Nanocatalysts on the Reforming Reactions of N-Heptane