Abstract:A supervisory Model Predictive Control (MPC) approach is developed for an air path system for multi-mode operation in a diesel engine. MPC is a control method based on a predictive dynamic model of system and determines actuator control positions through the optimization of various factors such as tracking performances of target setpoints, moving speed of actuators, limits, etc. Previously, linear MPC has been successfully applied on the air path control problem of a diesel engine, however, most of these applications were developed for a single operation mode which has only one set of control target setpoint values. In reality, a single operation mode cannot cover all requirements of current diesel engines and this complicates practical implementations of linear MPC. The high priority targets for the development of diesel engines are low emissions, high thermal efficiency and robustness. These objectives require multi-mode operations such as a HP EGR (High pressure exhaust gas recirculation) mode in cold coolant condition, a Double EGR mode for sufficient EGR rates, a Diesel Particulate Filter (DPF) regeneration mode for the heat-up of exhaust gas temperature and a rich mode of exhaust gas for Lean NOx Trap (LNT) regeneration. Each engine operation mode requires different target setpoints from the air path, such as air mass flow rate and oxygen concentration. In the multi-mode operation, simple linearization based MPC is limited in the practical application because a linearization point changes depending on target setpoints of each operation mode. This means that a linear model for a specific operation mode is not valid in other operation modes, which have different target setpoints. Moreover, the modern diesel air path system is highly nonlinear and would require a significant number of linear models to adequately represent the entire behavior not only at all operation points of engine speed and load, but also at the various operation modes. In this study, a new scheme is proposed and tested on a diesel engine utilizing combined benefits of a supervisory MPC and component level nonlinear compensators. The developed nonlinear compensators are based on dynamic real-time inversions of individual component models. The control scheme comprises of three parts: a supervisory MPC as the coordination of target setpoints in high-level to achieve the objectives, a component level control of nonlinear compensator, state observation either by virtual sensor or by Electronic Control Unit (ECU) sensor. The test results from an engine test bench and a chassis dynamometer demonstrates that the proposed method works well in multi-mode operation and can be applied with the significant benefit that no mode specific control strategies and calibration are needed. A valuable benefit of this approach can be seen in the calibration effort, particularly during development when the setpoints are not necessarily fixed.

Holistic Diesel Engine and Exhaust After-Treatment Model Predictive Control

Model predictive emissions control of a diesel engine airpath: Design and experimental evaluation

Development of a Model Predictive Airpath Controller for a Diesel Engine on a High-Fidelity Engine Model with Transient Thermal Dynamics

Hierarchical multi-time-scale predictive thermal management and fuel optimization for heavy-duty compression ignition engines

Model Predictive Control Case Study: Selective Catalytic Reduction (scr) System in Coal-Fired Power Plant

Get the design right, the rest is automatic: Towards an adaptive MPC controller

Hierarchical model predictive control for an off-highway diesel engine with SCR catalyst

Fuel and Emissions Optimization for Connected Diesel Engine Vehicles With Hierarchical Model Predictive Control

Model Predictive Control of an Air Path System for Multi-Mode Operation in a Diesel Engine

Model Predictive Controller with Average Emissions Constraints for Diesel Airpath

Model Predictive Supervisory Control for Integrated Emission Management of Diesel Engines

Diesel Engine Transient NOx and Airpath Control using Rate-based Model Predictive Controller

Experimental Study and Model Predictive Control of a Lean-Burn Gasoline Engine Coupled With a Passive Selective Catalytic Reduction System

Nonlinear Model Predictive Control of Integrated Diesel Engine and Selective Catalytic Reduction System for Simultaneous Fuel Economy Improvement and Emissions Reduction

Tuneable model predictive control of a turbocharged diesel engine with dual loop exhaust gas recirculation

Model Predictive Control of Diesel Engine Emissions Based on Neural Network Modeling

Model predictive control of a dual fuel engine integrated with waste heat recovery used for electric power in buildings

Nonlinear Predictive Control of Diesel Engine DOC Outlet Temperature

Closed-Loop Control Strategy and State Estimator for Diesel Engine SCR After-Treatment System

Hybrid Electric Vehicle Model Predictive Control Torque-Split Strategy Incorporating Engine Transient Characteristics

A softly switched multiple Model Predictive Control of a turbocharged Diesel engine