Abstract:BACKGROUND:During joint replacement, different materials of prosthesis can be used. Different prosthesis can produce different effects and the stress distribution of bone interface. OBJECTIVE:To explore the effects of different materials on the stress distribution and biomechanics of the bone interface of artificial hip joint. METHODS:The CT scan of the hip was carried out. The image data were saved in DICOM format and processed by MIMICS software. The 3D finite element model of the femur was obtained by ANSYS. A three dimensional finite element model of the femur was made with the material properties of the femur. Three kinds of different replacement prosthesis materials (Co Cr Mo aloy, titanium aloy and composite materials) were selected, and the specific requirements of the actual joint replacement were selected, and different types of prosthesis were designed in CAE software. In the STL format, the prosthesis model was imported into MIMICS, and the femur and prosthesis were assembled. The stress status of different prosthesis was analyzed, and the stress shielding rates of exterior and interior sides of middle and lower parts of the femur, right to and 30 mm below lesser trochanter and right to lesser trochanter of the proximal femur were calculated. RESULTS AND CONCLUSION:Through three-dimensional finite element analysis, a direct and accurate model of the femur and the three-dimensional model of the prosthesis were established. According to the actual situation, material assignment of the femoral three-dimensional finite element model was conducted to obtain the corresponding model. Thus, the properties of different materials of the femur were shown visualy. The femoral stress of cobalt chromium molybdenum aloy, titanium aloy, and composite material was simulated after replacement. Results found that the stress shielding rate can decrease in the middle and lower parts of the femur. After replacement, the femoral stress is higher than that of the intact femur. The experimental results show that the stress shielding of the joint was performed after joint replacement with Co Cr Mo aloy, titanium aloy and composite materials. Among them, the composite material is more close to the actual physiological environment of the human body, and it can better reduce the stress shielding effect, and is beneficial to the stress from the prosthesis to the femur.

Micromotion analysis of the head-neck interface of a PEEK artificial hip prosthesis

Wear mechanism and debris analysis of PEEK as an alternative to CoCrMo in the femoral component of total knee replacement

In Vitro Analysis of Wearing of Hip Joint Prostheses Composed of Different Contact Materials

Finite element analysis of elliptical shaped stem profile of hip prosthesis using dynamic loading conditions

Dynamic computational wear model of PEEK-on-XLPE bearing couple in total hip replacements

Effects of different materials on stress distribution and biomechanics of bone interface of artificial hip joint

Influence of Cross-Shear and Contact Pressure on Wear Mechanisms of PEEK and CFR-PEEK in Total Hip Joint Replacements

Stress Shielding and Bone Resorption of Press-Fit Polyether–Ether–Ketone (PEEK) Hip Prosthesis: A Sawbone Model Study

Effect of Progressive Wear on the Contact Mechanics of Hip Replacements – Does the Realistic Surface Profile Matter?

Understanding the role of head size and neck length in micromotion generation at the taper junction in total hip arthroplasty

A preclinical numerical assessment of a polyetheretherketone femoral component in total knee arthroplasty during gait

CFPEEK Composite Materials for Hip Prosthesis:Fabrication, Wear and Biological Fixation

Torsion Wear Behavior of PEEK-on-UHMWPE as an All-Polymer Joint Combination in Total Knee Replacement

In vitro wear study of PEEK and CFRPEEK against UHMWPE for artificial cervical disc application

Elastohydrodynamic lubrication analysis of polymer‐on‐polymer artificial hip joint of CF / PEEK composite

Swing-torsion composite friction behavior of CoCrMo/UHMWPE contact interface of artificial knee joint prosthesis implantation materials

Preclinical Evaluation of a Mini-Arthroplasty Implant Based on Polyetheretherketone and Ti6AI4V for Treatment of a Focal Osteochondral Defect in the Femoral Head of the Hip

Strain distribution in the proximal human femur after insertion of CF/PEEK femoral stems

Wettability and Frictional Studies of PEEK Composites against Co-Cr Alloys with Surface Textures

Carbon Fiber Composite for Acetabular Prosthesis-Fabrication,Wear and Biocompatibility

Analysis of contact pressure in a 3D model of dual-mobility hip joint prosthesis under a gait cycle