Abstract:Background: The effect of posterior tibial slope on the maximum contact pressure and wear volume of polyethylene (PE) insert were not given special attention. The effects of flexion angle, Anterior-Posterior (AP) Translation, and Tibial slope on the max contact pressure and wear of PE insert of TKR were investigated under loadings which were obtained in cadaver experiments by using Archard's wear law. This study uses not only loads obtained from cadaver experiments but also dynamic flexion starting from 0 to 90 degrees. Method: Wear on knee implant PE insert was investigated using a 2.5 size 3 dimensional (3D) cruciate sacrificing total knee replacement model and Finite Element Method (FEM) under loadings and AP Translation data ranging from 0 to 90 flexion angles validated by cadaver experiments. Two types of analyses were done to measure the wear effect on knee implant PE insert. The first set of analyses included the flexion angles dynamically changing with the knee rotating from 0 to 90 angles according to the femur axis and the transient analyses for loadings changing with a certain angle and duration. Results: It is seen that the contact pressure on the PE insert decreases as the cycle increases for both Flexion and Flexion+AP Translation. It is clear that as the cycle increases, the wear obtained for both cases increases. The loadings acting on the PE insert cannot create sufficient pressure due to the AP Translation effect at low speeds and have an effect to reduce the wear, while the effect increases with the wear as the cycle increases, and the AP Translation now contributes to the wear at high speeds. It is seen that as the posterior tibial slope angle increases, the maximum contact pressure values slightly decrease for the same cycle. Conclusions: This study indicated that AP Translation, which changes direction during flexion, had a significant effect on both contact pressure and wear. Unlike previous similar studies, it was seen that the amount of wear continues to increase as the cycle increases. This situation strengthens the argument that loading and AP Translation values that change with flexion shape the wear effects on PE Insert.

Dynamic computational wear model of PEEK-on-XLPE bearing couple in total hip replacements

Wear mechanism and debris analysis of PEEK as an alternative to CoCrMo in the femoral component of total knee replacement

Influence of Cross-Shear and Contact Pressure on Wear Mechanisms of PEEK and CFR-PEEK in Total Hip Joint Replacements

Torsion Wear Behavior of PEEK-on-UHMWPE as an All-Polymer Joint Combination in Total Knee Replacement

Enhanced computational modelling of UHMWPE wear in total hip joint replacements: The role of frictional work and contact pressure

Computational Wear Prediction for Impact of Kinematics Boundary Conditions on Wear of Total Knee Replacement Using Two Cross-Shear Models

Prediction of Wear Rates of UHMWPE Bearing in Hip Joint Prosthesis with Support Vector Model and Grey Wolf Optimization

Wear prediction for metal-on-metal hip joint replacements

Investigation of stair ascending and descending activities on the lifespan of hip implants

Dynamic finite element analysis of hip replacement edge loading: Balancing precision and run time in a challenging model

Total Hip Wear Assessment: A Comparison Between Computational and In Vitro Wear Assessment Techniques Using ISO 14242 Loading and Kinematics

Micromotion analysis of the head-neck interface of a PEEK artificial hip prosthesis

Sensitivity of total knee replacement wear to variability in motion and load input: A parametric finite element analysis study

A preclinical numerical assessment of a polyetheretherketone femoral component in total knee arthroplasty during gait

Computational wear of knee implant polyethylene insert surface under continuous dynamic loading and posterior tibial slope variation based on cadaver experiments with comparative verification

In vitro wear study of PEEK and CFRPEEK against UHMWPE for artificial cervical disc application

Development of a hybrid computational/experimental framework for evaluation of damage mechanisms of a linked semiconstrained total elbow system

Long-Term Follow-Up of Conventional Polyethylene in Total Hip Arthroplasty in Young Patients: Heightened Wear-Related Complications Are Observed at the Beginning of the Third Decade

Numerical Model of Ultra-High Molecular Weight Polyethylene Abrasive Wear Tests

In Vitro Analysis of Wearing of Hip Joint Prostheses Composed of Different Contact Materials

Finite element analysis of elliptical shaped stem profile of hip prosthesis using dynamic loading conditions