Abstract:The properties of sintered and heat-treated steels produced from the Catamold 8740 material by powder injection molding were examined. Parts made of the Catamold 8740 low-alloy mild carbon steel are used in the military, automotive, and other industries where high reliability and resistance to dynamic loads are required. The Catamold 8740 chemical homogeneity was studied as a function of powder injection molding parameters: heating rate, sintering temperature, holding time, and subsequent heat treatment. Microscopic analysis showed that Catamold 8740 was a mechanical mixture of powders in various sizes (carbonyl iron, nickel, Fe–Mo, Fe–Cr, Fe–Si-Mo, Fe–Si). When the heating rate of the Catamold 8740 powder mixture increased from 2 to 5 °C/min, the microstructural heterogeneity caused by uneven compaction decreased and the alloy formation process activated at 900–1340°C. The impact strength of Charpy V-notch test samples changed from 10.39 to 11.52 J/cm2 with higher sintering temperature and heating rate increasing from 2 °C/min (1270°C) to 5 °C/min (1340°C). When holding time increased from 30 to 90 min at a sintering temperature of 1340°C, the material became denser, the pores rounded, and the ferrite matrix homogeneous. However, the impact strength decreased by a factor of 1.4 because of coarser grain sizes and brittle fracture. Heat treatment processes reduced the impact strength after sintering. The results obtained were used to optimize the powder injection molding parameters. The influence of chemical and dimensional inhomogeneity of the starting Catamold 8740 powders and sintering kinetics on the structure and mechanical properties of parts operating under impact loads was established.

Rheological and Thermal Characterization of AISI 4605 Low-Alloy Steel Feedstock for Metal Injection Molding Process

Investigating the Effect of Stearic Acid on the Mechanical, Rheological, and Microstructural Properties of AISI 4605 Feedstock for Metal Injection Molding Process

Characterization of 17-4 PH stainless steel metal injection molding feedstock using mixing torque data

Integrated Numerical Simulations and Experimental Measurements for the Sintering Process of Injection-Molded Ti-6Al-4V Alloy

Investigation of Rheological Behavior of Low Pressure Injection Molded Stainless Steel Feedstocks

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Effect of surface modification of metal powders (by aluminum stearate) on the properties of metal injection molding feedstock

The effect of Cu–8%P master alloy, SIMA process, thixoforming, and heat treatment on the microstructure and mechanical properties of Al–20%Mg 2 Si composite

Microstructure and mechanical properties of gamma titanium aluminide alloys fabricated by metal injection molding using non-spherical powder

Assessment of Residual Stress Behavior and Material Properties in Steels Produced via Oxynitrocarburized Metal Injection Molding

Numerical Simulation and Experimental Investigation of Microstructure Evolution and Flow Behavior in the Rheological Squeeze Casting Process of A356 Alloy

Preparation of optimal feedstock for low-pressure injection molding of Al/SiC nanocomposite

Optimization of the Sintering Parameters for Materials Manufactured by Powder Injection Molding

Fabrication of large cross-section Ti–6Al–4V alloy using EBS-modified POM-based feedstock

Deformation Characteristics and Constitutive Equations for the Semi-Solid Isothermal Compression of Cold Radial Forged 6063 Aluminium Alloy

Thermal-Transient Analysis for Cooling Time on New Formulation of Metal Epoxy Composite (MEC) as Mold Inserts

Optimization of composite extrusion modeling process parameters for 3D printing of low-alloy steel AISI 8740 using metal injection moulding feedstock

Optimization of numerical parameters and microstructure evolution on 2195 Al–Li alloy extrusion process

Systematic Analysis of Distinct Flow Characteristics and Underlying Microstructural Evolution Mechanisms of a Novel Fine-Grained P/M Nickel-Based Superalloy During Isothermal Compression

Processing and Characterization of AA2618/Sicp Metal Matrix Composites by Stir Casting Method

A modified Johnson-Cook model to determine plastic flow behavior of Fe-30Mn-9Al-0.8 C low-density steel during warm multiaxial forging