Abstract:Highlights • Electrified steam methane reforming process digitalization and control. • Model development for real-time control. • Model predictive control design accounting for practical concerns. • Successful experimental implementation of MPC. Steam methane reforming (SMR) is the most common industrial process to produce hydrogen (H 2 ) from methane and water vapor. The SMR reactions are overall highly endothermic and traditionally, fossil fuels are burned to provide the necessary heat of reaction. However, it was found that electrifying the tubular SMR reactors using renewable electrons instead of conventional heating gives the opportunity of producing H 2 with lower carbon emissions, lower reactor volumes, and higher carbon conversion. While current studies in this new technology focus on improving the catalysts or heating sources, a more efficient process control scheme can also significantly contribute to the understanding of potential challenges and opportunities of combining renewables and natural gas in the production of H 2 at industrial scales. In order to further develop the electrically-heated SMR process and the associated control strategies, we have constructed an experimental Joule-heated SMR system at UCLA. The system contains a tubular reactor with a washcoated Ni/ZrO 2 catalyst, two thermocouples connected to the top and bottom of the reactor, a power supply for providing electrical heating, and an on-line gas chromatograph (GC) for measuring outlet gas concentrations. The synthesis procedure of the catalyst, SMR data collection, and thermal considerations for catalyst degradation are described in this paper and are all accounted for experimentally when using a proportional integral (PI) controller to gradually increase the reactor temperature without harming the catalyst. Advanced control strategies, such as model predictive control (MPC), require a process model that uses measurement feedback to make predictions of the process time-evolution in order to optimize the control actions in real-time. We have previously developed a lumped-parameter modeling strategy for the SMR process. The MPC objective is to control the H 2 production rate by manipulating the current flowing through the outer reactor shell. However, to use this model in an MPC, feedback values for all state variables should be provided by the sensors. In our experimental system, the on-line GC only gives discrete measurements with a long sampling period. To this end, the process model is incorporated into an extended Luenberger observer (ELO) that uses the reactor temperature and GC measurements to provide estimates of all the variables needed by the MPC. The ELO-based MPC system is then experimentally implemented on the process and it is demonstrated to be more efficient in terms of speed of the closed-loop response than the PI controller using delayed, measurement feedback by the GC.

Control of regenerative catalytic oxidizers used in coal mine ventilation air methane exploitation

Combustion of coal mine ventilation air methane in a regenerative combustor with integrated adsorption: Reactor design and optimization

Model Predictive Control Case Study: Selective Catalytic Reduction (scr) System in Coal-Fired Power Plant

Get the design right, the rest is automatic: Towards an adaptive MPC controller

A Novel Adaptive Generic Model Control Strategy for Internal Thermally Coupled Air Separation Columns with Multivariable Recursive Estimation.

Multi-Objective Adaptive Optimization Model Predictive Control: Decreasing Carbon Emissions from a Zinc Oxide Rotary Kiln

Analysis of the Effects of Structural Parameters on the Thermal Performance and System Stability of Ventilation Air Methane-Fueled Reverse-Flow Oxidation Reactors

Coal mine ventilation air methane combustion in a catalytic reverse flow reactor: Influence of emission humidity

Feedback control of an experimental electrically-heated steam methane reformer

Demonstration of mitigation and utilization of ventilation air methane in a pilot scale catalytic reverse flow reactor

Nonlinear Predictive Control of Diesel Engine DOC Outlet Temperature

Application of an Improved State Feedback Control in the Selective Catalytic Reduction Denitrification Systems of Coal Power Units Under Variable Load Conditions

An Adaptive P/PI Control Strategy for a Solar Volumetric Methane/steam Reforming Reactor with Passive Thermal Management

Hybrid Advanced Control Strategy for Post-Combustion Carbon Capture Plant by Integrating PI and Model-Based Approaches

Data-driven based multi-objective combustion optimization covering static and dynamic states

Iterative Learning Control of Methane Steam Reforming Reaction in Operating Solid Oxide Fuel Cell

Experimental Study on Ultra-Low Concentration Methane Regenerative Thermal Oxidation

Multi-index control strategy from cement calcination denitration system: a model predictive control method for combined control of nitrogen oxide and ammonia escape

Dynamic modeling and control for pulverized-coal-fired oxy-combustion boiler island

Model Predictive Control of District Heating Grids Using Stabilizing Terminal Ingredients

A new strategy for upgrading ventilation air methane emissions combining adsorption and combustion in a lean-gas turbine