Abstract:To mitigate the challenges posed by anthropogenic climate interference, substantial efforts are imperative in order to limit the rise in global average temperature. One major declaration made by the international community through various climate agreements [1,2] calls for an elimination of greenhouse gas emissions, necessitating a shift from fossil fuels to sustainable renewable energy sources. Hydrogen and hydrogen-based fuels emerge as promising candidates to decarbonize a wide range of sectors – including transport, industry and chemical manufacture – due to hydrogen’s remarkable flexibility and storage capacity. At present, water electrolysis conducted by renewable electricity is considered as the most sustainable technology to produce green hydrogen. Among the various approaches for water electrolysis, two commercially available methods stand out: alkaline and proton exchange membrane (PEM) [3]. Alkaline water electrolysis (AWE) has the advantage of presenting the lowest cost per kilowatt of electricity but yields lower hydrogen production rates. In contrast, PEM electrolysis achieves superior performance, thanks to the use of costly and scarce electrocatalytic materials like Ir and Pt. Considering the unique strengths of each system, it is appealing to try to integrate the best of these two technologies, yielding high production rates per electrode area while benefiting from more cost-effective electrode materials. To this end, recent experimental work in our group has focused on the conception and analysis of flow-engineered 3-D electrodes into a novel laterally-graded cell configuration to allow alkaline water electrolysis to become PEM-like [4,5]. More specifically, 3-D electrodes such as foams were integrated into a zero-gap cell using a bi-layer configuration in which a fine foam (450 μm pore size) working as a catalytic electrode is put in contact with a coarser foam (3000 μm pore size) acting as a porous transport layer (PTL). Because of the high production rate in the 450 μm foam, a high forced upstream electrolyte flow is used to favour bubble removal and hence decrease the Ohmic resistance of the system. Thanks to the use of a bi-layer configuration in flow-through upstream flow mode, the many bubbles generated near the diaphragm were believed to be evacuated laterally towards the coarser foam, keeping the catalytic surface of the finer foam active throughout the process. The enhanced performance of this PEM-like system was confirmed experimentally and current densities of 2 A/cm 2 were observed at cell voltages lower than 2 V (for 2 x 2 x 0.56 cm 3 electrodes). The aim of this work is to use Computational Fluid Dynamics (CFD) simulations in order to assess flow behaviour into the bi-layer and validate the assumptions that were made based on the experimental results. First of all, a single-phase model (i.e. considering only the electrolyte) was used to solve the incompressible Navier-Stokes equations in OpenFOAM. The objective is to shift towards multiphase simulations by considering a simple mixture model to account for the presence of gas bubbles. The driftFluxFoam solver will be used to solve the general mixture model equations, in which velocity, density and viscosity are weight-averaged based on gas fraction and on the properties of both phases. This work also highlights two ways of incorporating porous media in the numerical simulations. The first way, called explicit, is based on the exact geometry of the foams, obtained thanks to high-resolution micro-CT (computed tomography) scanned data, but is extremely costly from a numerical point of view. The other method, called implicit, uses the Darcy-Forchheimer approximation to spatially average porosity over a given domain, which is less representative of the exact foam structure but generally allows to get first useful insights of the flow behaviour in porous media. An example of a laterally graded bi-layer configuration and some initial multiphase results are shown in Figure 1. The velocity vectors and the lateral velocity profile confirm that hydrogen bubbles can indeed be expected to be evacuated from the fine catalytic 450 μm into the coarser 3000 μm PTL foam. The main objective of our modeling approach is to demonstrate the relation between the observed electrochemical performance enhancement with multiphase mass transport phenomena occurring inside the 3-D electrodes in order to show the intrinsic interest of using such laterally graded bi-layer approach in all future alkaline water electrolysers. Figure 1

CFD simulation of biphasic flow, mass transport and current distribution in a continuous rotating cylinder electrode reactor for electrocoagulation process

Modeling the electrocatalytic nitrate removal in a rotating cylinder electrode reactor

Multiphysics Modeling of Electrode Dissolution Under Hydrodynamic Conditions in Low Conductivity Water

CFD Modeling and Experimental Validation of an Alkaline Water Electrolysis Cell for Hydrogen Production

CFD modeling of multiphase flow in an alkaline water electrolyzer

Exploring an Electrochemical Batch Reactor for Nutrient Recovery from Wastewater: Continuum Modeling Analysis of Hydrodynamics and Tertiary Current Distribution

Computational fluid dynamic for improving design and performance of an external loop airlift reactor used in electrochemical wastewater treatment

Influencia de la convección forzada sobre la cinética de electrodeposición de Fe, Co, y Fe-Co en el disolvente eutéctico profundo Cloruro de Colina-Urea

CFD simulation of two-phase flow in a batch-mode electrodialysis of lithium sulphate: Effect of gas evolution

Intensification of a new electrocoagulation system characterized by minimum energy consumption and maximum removal efficiency of heavy metals from simulated wastewater

Hydraulic Characteristics, Residence Time Distribution, and Flow Field of Electrochemical Descaling Reactor Using CFD

Simulation of aluminium electrodeposition on complex geometry: Influence of input parameters and electrodeposition conditions

Three-dimensional Simulation of Alkaline Electrolyzer with an Advanced Partitioned Point Flow Channel

Multiphase Modeling of Enhanced Bubble Evacuation in Alkaline Water Electrolysis Cells Based on Laterally-Graded 3-D Electrodes

A novel combined system for efficient nitrate removal using a continuous flow electrocoagulation and sand filtration (FECF) reactor: Statistical analysis by Taguchi design

Investigation of the geometry of an electrochemical reactor in order to minimize the operational energy cost in the treatment of cosmetic effluents

Effect of current density on COD removal efficiency for wastewater using the electrocoagulation process

Eulerian Two-Fluid Model of Alkaline Water Electrolysis for Hydrogen Production

Non-uniform liquid flow distribution in an alkaline water electrolyzer with concave-convex bipolar plate (CCBP): A numerical study

Transient MHD Darcy-Forchheimer of Williamson-Casson flow with CCS: Application of wastewater treatment

Optimization of Active Chlorine Production in a Filter-Press Type Electrochemical Reactor through Continuum Modelling and Response Surface Methodology