Abstract:In this work an investigation into the effect of alloying additions (Mn, Cu, Sb and Zr) on microstructure and corrosion of Zn alloys and hot dip galvanised coatings was undertaken. The first part of this thesis focuses on the effect of alloying additions on the corrosion of Zn alloys. The result shows that Mn is the most beneficial addition, which can significantly improve the resistance of Zn. The effect of Cu depends on its concentration. A high level of Cu addition has a deleterious effect on the corrosion resistance as the Cu-rich particles are catalytic cathodic sites for oxygen reduction. Additions of Zr and Sb were found to have minor effect on the corrosion behaviour of Zn alloys. The effect of these additions on the microstructure of hot dip galvanised coatings was investigated in the second part. Both Zr and Mn can inhibit the layer growth of active steels with high Si content. Thus, Mn and Zr might be an alternative addition to Ni which can control the excessive reaction of the active steels. Addition of 0.8 wt % Cu significantly increases the coating thickness of the galvanised steel containing 0.02 wt % Si. The growth kinetics of the alloy layers follows a linear law. The final part of this thesis focuses on the effect of these additions on the atmospheric corrosion resistance and electrochemistry of hot dip galvanised coatings. Among the alloying additions investigated in this study, Mn is the most beneficial addition to the Zn bath and can significantly improve the resistance of the hot dip galvanised coating to atmospheric corrosion. The effect of other additions on corrosion resistance is minor. The beneficial effect of Mn addition is mainly due to the formation of a Mn-rich oxide layer on the top surface during the galvanising process, which can greatly inhibit the cathodic reactivity of the hot dip galvanised coating. Coupled with the relatively low cost and ease of alloying of this element, these various factors suggest that Mn might have broader applications in general galvanising.

Microstructure, phase evolution and corrosion behaviour of the Zn–Al–Mg–Sb alloy coating on steel

Effect of antimony additions on the microstructure and performance of Zn–Mg–Al alloy coatings

Solidification microstructure of Zn-(0-6.0%)Al-4%Sb alloys used for hot-dip galvanizing

Behaviors and Effects of Zn Coating on Welding-Brazing Process of Al-Steel and Mg-steel Dissimilar Metals

The influences of Zn、Sb、Ti、Zr on the corrosion of ZL114A alloy

Effects of Al content on microstructure and corrosion behavior of Zn-Al alloy coatings

Microstructure and Corrosion Resistance of Solidified Zn-Al-Mg Alloys

Microstructure and Corrosion Resistance Property of a Zn-AI-Mg Alloy with Different Solidification Processes

The Solidification and Corrosion Behavior Determination of the Ti/B Added Zn-Al-Mg Alloys

Roles of Al and Mg on the Microstructure and Corrosion Resistance of Zn-Al-Mg Hot-Dipped Coated Steel

Experimental Investigation and Kinetic Analysis of Al–Zn–Mg Alloy Coating

Effect of Cooling Rate on Solidification Structure of Zinc-Aluminum-Magnesium Alloy

Effects of Al-Mg on the Microstructure and Phase Distribution of Zn-Al-Mg Coatings

Study of Microstructure and Corrosion Behavior of Cast Zn–Al–Mg Alloys

Corrosion Behaviour of Arc Sprayed Zn55Al Coatings on Q235 Steel in 3.5 wt% NaCl Solution

Microstructure, Mechanical Properties and Corrosion Behaviors of Al–Li–Cu–Mg–Ag–Zn Alloys

Influence of Si contents on the microstructure and corrosion resistance of the Zn−Al−Mg−Si alloys

Microstructure, Tensile Properties, and Corrosion Behavior of Die-Cast Mg-7Al-1Ca- X Sn Alloys

Development of Corrosion Resistant Galvanising Alloys

Effects of Sb on corrosion behavior of Mg-6Al alloy

The Effect of B and Sb on the Corrosion Behavior of T6-treated Al-Si-Mg Alloys