Abstract:Copper as well as copper base composites reinforced with coated and uncoated 1 wt% diamond, graphite particles or short carbon fibers are prepared by powder metallurgy process. The reinforcement particles were encapsulated with silver as well as copper layer by using the electroless deposition technique to investigate the influence of the reinforcement surface coating on the microstructure, density, electrical and thermal properties of the sintered samples. The coated and the uncoated powders were cold compacted at 600 MPa, and then sintered at 1173 K (900°C) for 2 h under hydrogen atmosphere. The phase composition, morphology and microstructure of the prepared powders as well as the copper base sintered composites were investigated using X-ray diffraction analysis (XRD) and Scanning Electron Microscope (SEM) equipped with an Energy Dispersive Spectrometer (EDS) respectively. The density of the sintered composites was measured by Archimedes method. The copper base consolidated composites had a density up to 96% and the reinforcement coated particles were distributed uniformly within the copper matrix better than the uncoated one. The electrical resistivity at room temperature and the heat transfer conduction of the produced samples were measured in a temperature range between 323 K (50°C) and 393 K (120°C). The results observed that the sintered materials prepared from the coated powder have lower electrical resistivity than the sintered materials prepared from the mixed powders. On the other hand the thermal conductivity values were calculated using the heat transfer conduction values by means of the Fourier formula. The results observed that the thermal conductivity of copper is (391 W/m·K), 1 wt% diamond/Cu is (408 W/m·K), 1 wt% graphite coated silver/Cu is (393 W/m·K), 1 wt% Cu coated short carbon fiber/Cu is (393 W/m·K), graphite/Cu is (383 W/m·K) and short carbon fiber/Cu is (382 W/m·K). The obtained composites are expected to be suitable for heat sink applications. The heat transfer testing experiments were done. The forced convection of the present work was done and compared with the previous work in the literature, and satisfactory agreement was achieved.

Physical and mechanical properties and structure of copper-based composite materials for diamond tools binder

Mechanical Alloying of Copper- or Iron-Based Metallic Binders for Diamond Tools

Improvement in Hardness and Wear Behaviour of Iron-Based Mn–Cu–Sn Matrix for Sintered Diamond Tools by Dispersion Strengthening

Structure and properties of composite materials based on copper strengthened with diamond nanoparticles by mechanical alloying

Study on the Microstructure and Mechanical Properties of Diamond Particle-Reinforced Copper-Iron Sandwich Composites Prepared by Powder Metallurgy

Enhanced Interfacial Bonding in Copper/Diamond Composites via Deposition of Nano-copper on Diamond Particles

Tribological, mechanical and thermal response of diamond micro-particles reinforced copper matrix composites fabricated by powder metallurgy

Fabrication, Microstructure, Thermal and Electrical Properties of Copper Heat Sink Composites

Development of heat- and wear-resistant nanocomposite copper powder based material and technique of its obtaining used for plungers of die-casting machines

Influence of the powder metallurgy route on the mechanical properties of Cu–Cr–diamond composites

Investigation into the Peculiarities of Structure Formation and Properties of Copper-Based Powder Pseudoalloys Modified by ZnO and TiN Nanoparticle Additives

Experimental Investigation on Tribological Behaviour of Copper Diamond Composites

Thermal conduction and strength of diamond-copper composite sandwich obtained by SPS diffusion bonding with Ti interlayer

Influence of diamond parameters on microstructure and properties of copper-based diamond composites manufactured by Fused Deposition Modeling and Sintering (FDMS)

Simulation, forming process and mechanical property of Cu-Sn-Ti/diamond composites fabricated by selective laser melting

Characterization of Iron – Based Partial Pre - Alloyed Powders as Matrix Materials for Diamond Tools

Copper–micrometer-sized diamond nanostructured composites

Strengthening Mechanisms and Thermal Models of Chemically Incompatible Metals (Mo/W‐Cu): A Review

Microstructure, mechanical and tribological properties of Cu-Sn/Cr3C2/Gr composites

RESEARCH OF THE COMPOSITION INFLUENCE OF COMPOSITES CONTAINING IMPACT DIAMONDS ON THEIR PERFORMANCE CHARACTERISTICS IN BLADE PROCESSING OF NON-FERROUS METALS

Research status and development trend of preparation technology of ceramic particle dispersion strengthened copper-matrix composites