Abstract:To date, the most commonly used aluminum alloys for additive manufacturing are eutectic/near-eutectic alloys. However, fabricating high strength aluminum parts has not yet been fully investigated due to solidification cracking and porosity formation, which make these alloys very hard to be processed. Electron beam selective melting (EBSM) of aluminum alloys has some advantages over selective laser melting. The process is not affected by reflectivity of aluminum powders, and parts exhibit less induced thermal stresses. In addition, oxidation is reduced due to vacuum condition. Therefore, the process provides high potential for the fabrication of aluminum alloys, specifically, Al2024 alloy which is widely used in different industries such as automotive and airline industries. Hence, these industries are highly benefitted from being able to build defect-free AM parts. This study is significant because Al2024 alloy is highly susceptible to solidification cracking and porosity formation, and crack-free samples with high relative densities have not been built by EBM process previously. The baseplate preheating temperature was set to 350 degrees C, and samples were fabricated by applying a proper powder bed preheating configuration for each layer. Different sets of processing parameters were used to investigate their effect on the performance of the parts. Archimedes technique was used to measure the relative density of samples, ranging from 95% to full-dense. The results showed that higher relative densities could be achieved by increasing the input energy to an optimum value; however, by further increasing the energy, the relative density decreases, which can be attributed to porosity formation. SEM and EBSD results showed equiaxed grains in a crack-free microstructure. Grain structure consisted of high angle grain boundaries having different crystallographic orientations with a few subgrains. Additionally, AlCuMnFe, AlCuMnFeSi, and eutectic Al2Cu phases were uniformly distributed in the alpha phase matrix. Microhardness results showed an almost uniform change of hardness values in both horizontal and vertical sections, ranging from 100 HV to 110 HV for as-built samples. Moreover, tensile and yield strengths of as-built samples reached 314 MPa and 191 MPa, respectively, which can be further increased by a proper post-processing treatment. (C) 2020 Elsevier B.V. All rights reserved.

Processing of High‐Carbon Steel by Selective Electron Beam Melting

Processing of the Heat Resistant Bearing Steel M50NiL by Selective Laser Melting

Additive manufacturing of metallic components by selective electron beam melting — a review

Selective Electron Beam Melting Technique and Its Application

On the Microstructural and Cyclic Mechanical Properties of Pure Iron Processed by Electron Beam Melting

Photopolymerization of Stainless Steel 420 Metal Suspension: Printing System and Process Development of Additive Manufacturing Technology toward High-Volume Production

Additive manufacturing of Ti-45Al-4Nb-C by selective electron beam melting for automotive applications

Dual-Material Electron Beam Selective Melting: Hardware Development and Validation Studies

Metal Fabrication by Additive Manufacturing Using Laser and Electron Beam Melting Technologies

Developing New Materials for Electron Beam Melting: Experiences and Challenges

PBF-EB of Fe-Cr-V Alloy for Wear Applications

Current Status of Electron Beam Selective Melting Additive Manufacturing Technology

Porosity, cracks, and mechanical properties of additively manufactured tooling alloys: a review

Selective electron beam melting of high strength Al2024 alloy; microstructural characterization and mechanical properties

Processing of Niobium-Alloyed High-Carbon Tool Steel via Additive Manufacturing and Modern Powder Metallurgy

Selective Laser Melting and Mechanical Properties of Stainless Steels

Processing of High Interstitial Austenitic Steel with PBF‐LB/M‐Evolution of chemical inhomogeneity and microstructural features during Post‐Processing

Microstructure evolution and mechanical properties of H13 steel produced by Selective Electron Beam Melting

Process Setup and Boundaries of Wire Electron Beam Additive Manufacturing of High-Strength Aluminum Bronze

INVESTIGATION OF THE STRUCTURE AND PROPERTIES OF FERROUS NICKEL ALLOYS AFTER MOLDING BY SELECTIVE LASER MELTING

Highly Anisotropic Steel Processed by Selective Laser Melting