Abstract:A paraffin–cellulose composite model was created using Materials Studio software, establishing a cellulose chain with a polymerization degree of 20 and paraffin molecules. A theoretical foundation for the research of wood heat treatment was established by explaining the changes in macroscopic qualities, such as mechanical properties, water absorption, etc., from a microscopic point of view. The model tended to a stable state with lower energy through geometric optimization and kinetic relaxation. The dynamics simulation was run based on this condition at a total of five different temperatures: 100 °C, 150 °C, 170 °C, 190 °C, and 210 °C. The energy balance, paraffin molecular diffusion coefficients, cell parameters and densities, hydrogen bonding numbers and mechanical parameters of the paraffin–cellulose composite model were analyzed. The results demonstrated that the paraffin diffusion range increased with temperature, and the paraffin diffusion coefficient was greatest at 210 °C, which also resulted in the maximum cell volume, the lowest density, and the lowest water absorption at this temperature. On the other hand, the paraffin–cellulose hybrid model had the most hydrogen bonds and the most stable system at 100 °C. The mechanical properties of the amorphous cellulose region of wood are influenced by temperature. According to the calculation of Lamé constants, with the system's temperature rise, Young's modulus (E) and shear modulus (G) were maximum at 100 °C, indicating the wood's optimal toughness and plasticity. Poisson's ratio and K/G values were largest at 210 °C, indicating the optimal toughness and plasticity of wood. The thermal modification of wood under different conditions can not only retain its natural advantages, but also improve its own performance, expand the application range of wood, and increase the utilization rate of wood. Therefore, the appropriate temperature and other conditions can be selected according to the actual needs of the wood heat treatment, which has significant practical significance for the study of wood heat treatment.

Effects of thermal modification on the mechanical properties of the wood cell wall of soft wood: behavior of S2 cellulose microfibrils under tensile loading

XRD investigation of mechanical properties of cellulose microfibrils in S1 and S3 layers of thermally modified wood under tensile loading

Molecular-level characterization of changes in the mechanical properties of wood in response to thermal treatment

Swelling restraint of thermally modified ash wood perpendicular to the grain

Effect of Thermo-Hydro-Mechanical Treatment on Mechanical Properties of Wood Cellulose: A Molecular Dynamics Simulation

Effect of Thermal Modification on the Nano-Mechanical Properties of the Wood Cell Wall and Waterborne Polyacrylic Coating

Synchrotron X-ray measurements of cellulose in wood cell wall layers of Pinus densiflora in the transmission and reflectance modes. Part 2: results with axial loading

A Study on the Effects of Vacuum, Nitrogen, and Air Heat Treatments on Single-Chain Cellulose Based on a Molecular Dynamics Simulation

Structural Changes of Oak Wood Main Components Caused by Thermal Modification

Effect of Pressurized Hydrothermal Treatment on the Properties of Cellulose Amorphous Region Based on Molecular Dynamics Simulation

Thermal modification of wood—a review: chemical changes and hygroscopicity

Effects of thermal treatment on the mechanical properties of larch (Larix gmelinii) and red oak (Quercus rubra) wood cell walls via nanoindentation

Effect of High-Temperature Paraffin Impregnation on the Properties of the Amorphous Cellulose Region Based on Molecular Dynamics Simulation

Mechanical properties changes in fir wood (abies sp.), linden wood (tilia sp.), and beech wood (fagus sp.) subjected to various thermal modification process conditions

Effects of Thermal Modification on the Flexure Properties, Fracture Energy, and Hardness of Western Hemlock

New Perspective on Wood Thermal Modification: Relevance between the Evolution of Chemical Structure and Physical-Mechanical Properties, and Online Analysis of Release of VOCs

Molecular Dynamics Study of Thermodynamic Properties of Cellulose Iβ Crystal

Thermal degradation of hemicellulose and cellulose in ball-milled cedar and beech wood

Chemical Structure and Mechanical Properties of Wood Cell Walls Treated with Acid and Alkali Solution

Evaluation of the Colour Parameters on Hygroscopicity and Dimensional Stability of Thermally Modified Populus Tomentosa Carr.

Chemical Composition and Selected Physical Properties of Oak Wood (Quercus robur L.) Modified by Cyclic Thermo-Mechanical Treatment