Abstract:At present, most high-performance cellulose matrix composites only use cellulose as reinforcement material, which is an obstacle to maximize the advantages of nanocellulose in structure and properties. The development of new functional nanocomposites with cellulose as the main component can better meet people's needs for high-performance and degradable composites, which requires a comprehensive and thorough understanding of cellulose. Considering the limitations of physical experiments, we performed molecular dynamics simulation of the uniaxial tensile behavior of the cellulose system at three different strain rates (10−4/ps, 10−5/ps, and 10−6/ps), and the stress-strain responses of cellulose systems at different strain rates are obtained. The effect of the strain rate on the mechanical properties of amorphous cellulose system during the tensile processes is analyzed. The deformation mechanism of cellulose amorphous system during the tensile processes is characterized by the energy changes of the different terms including dihedral angle torsion term, bond tensile term, angle bending term, and nonbond term. Structural evolution of the cellulose crystal system during the tensile processes is used to explain the failure mechanism of cellulose. The kinetic simulation results show that the mechanical properties of the cellulose amorphous system increase with the increase of strain rate. Compared with the strain rate of 10−5/ps, the elastic modulus of the system increases by 6.73 GPa at the strain rate 10−4/ps. During the tensile processes, cellulose amorphous region adapts to the applied load mainly through the stretching of the cellulose macromolecular chains, i.e., the deformation of bond lengths and bond angles, without any breakage of the molecular chains. The main causes of chain lengthening at different strain rates are different. The failure of cellulose is caused by the slip and rearrangement of some molecular chains in the crystal structure.

XRD investigation of mechanical properties of cellulose microfibrils in S1 and S3 layers of thermally modified wood under tensile loading

Effects of thermal modification on the mechanical properties of the wood cell wall of soft wood: behavior of S2 cellulose microfibrils under tensile loading

Synchrotron X-ray measurements of cellulose in wood cell wall layers of Pinus densiflora in the transmission and reflectance modes. Part 2: results with axial loading

Molecular-level characterization of changes in the mechanical properties of wood in response to thermal treatment

Effect of Thermo-Hydro-Mechanical Treatment on Mechanical Properties of Wood Cellulose: A Molecular Dynamics Simulation

Effect of Thermal Modification on the Nano-Mechanical Properties of the Wood Cell Wall and Waterborne Polyacrylic Coating

Understanding the mechanical strength and dynamic structural changes of wood-based products using X-ray computed tomography

Mechanism of wood deformation cascading from nanoscale to macroscale in response to moisture desorption

Swelling restraint of thermally modified ash wood perpendicular to the grain

Effect of Pressurized Hydrothermal Treatment on the Properties of Cellulose Amorphous Region Based on Molecular Dynamics Simulation

Chemical Structure and Mechanical Properties of Wood Cell Walls Treated with Acid and Alkali Solution

A Study on the Effects of Vacuum, Nitrogen, and Air Heat Treatments on Single-Chain Cellulose Based on a Molecular Dynamics Simulation

Structural Changes of Oak Wood Main Components Caused by Thermal Modification

Molecular Dynamics Simulation on Tensile Behavior of Cellulose at Different Strain Rates

Drying-induced bending deformation of cellulose nanocrystals studied by molecular dynamics simulations

Understanding the origin of microcompressions in cellulose fibres using 4D X-ray micro-computed tomography

Terahertz time-domain spectroscopy as a novel tool for crystallographic analysis in cellulose: tracking lattice changes following physical treatments

Gradient variations of cellulose supramolecular structures in moso bamboo culm: from nano- to microhorizons

Contribution of lignin to the strength properties in wood fibres studied by dynamic FTIR spectroscopy and dynamic mechanical analysis (DMA)

Effects of Thermal Modification on the Flexure Properties, Fracture Energy, and Hardness of Western Hemlock

Mapping humidity-dependent mechanical properties of a single cellulose fibre