Abstract:<p>A novel dual-serpentine-channel flat-plate oscillating heat pipe (FPOHP) is designed and fabricated for electronic cooling with multiple heat sources and sinks. The FPOHP has two mirror symmetric tandem branches of capillary serpentine square channel with a hydraulic diameter of 2 mm (i.e., Bond number <em>Bo</em> = 1.137~1.265 here), which is made of 6063 aluminum alloy and 55% partially filled with acetone. A corresponding experimental study is conducted to investigate the start-up characteristics and quasi-steady thermal performance of the FPOHP with arrangement of "uniform heating by multiple heat sources at center and air cooling at both ends" under different inclination angles. The combined flow pattern diagrams as well as thermal resistance and equivalent thermal conductivity contour maps are provided for two mirror symmetric tandem sections of the FPOHP, based on which the thermo-hydrodynamic performance deviations between these two sections are compared and analyzed. The results show that the quasi-steady fluid motions in the FPOHP can be characterized by intermittent or independent occurrence of three elements, namely, stop, oscillation, and circulation, depending on the heat load and inclination angle. Significantly, the thermo-hydrodynamic behaviors in two tandem sections of the FPOHP both cooperate and compete with each other, as a result of the heat, mass and momentum exchanges via the tandem structure. The FPOHP can start up successfully under all inclination angles from 0° to 90° with no obvious difference, and its start-up temperature increases smoothly and approximately reaches a plateau of 41~46 °C as the heat load goes up. For the 175 tested conditions, the coefficients of variation for the thermal resistance of two tandem sections are smaller than 21.5% with the average value of 6.8%, showing a fine heat transfer uniformity of the FPOHP over a wide range of operating conditions. Significantly, in general, the FPOHP has much larger overall equivalent thermal conductivity (about 5.8 times on average) and possesses only a weight 83.6% of a pure 6063 aluminum alloy plate with the same geometry. In addition, the FPOHP exhibits a well gravity adaptability with the relative deviation ranging from 7.1% to 25.2% in the total thermal resistances for all inclination angles. Accordingly, the FPOHP shows a good potential for the high-heat-flux electronic cooling applications with multiple heat sources and sinks.</p>

Experimental investigation of the thermal performance of closed loop flat plate oscillating heat pipe

Experimental Investigation on the Heat Transfer Performance and Evaporation Temperature Fluctuation of a New-Type Metal Foam Multichannel Heat Pipe

Experimental and theoretical investigation of the influence of heat transfer rate on the thermal performance of a multi-channel flat heat pipe

Experimental and Theoretical Study on Operation Characteristics of an Oscillating Heat Pipe

Experimental Investigation of Heat Transfer Characteristics in a Miniature Flat Heat Pipe with Multi-Channels

Thermal performance of a novel dual-serpentine-channel flat-plate oscillating heat pipe used for multiple heat sources and sinks

Experimental investigation on the thermal performance of a novel loop heat pipe (LHP) with micro-channel structure

Experimental investigation of flow visualization and thermal performance of flat-plate single-loop pulsating heat pipes

Influence of Working Fluid Thermophysical Property on Thermal Performance of Flat-Plate Closed Loop Pulsating Heat Pipe

Thermal and Visual Observation of Water and Acetone Oscillating Heat Pipes

Parametric Study on Ammonia-Based Loop Heat Pipe

Experimental Study on Thermal Performance of a Novel Serpentine-Looped Flat Microchannel Heat Pipe

Study on Heat Transfer Performance of an Aluminum Flat Plate Heat Pipe with Fins in Vapor Chamber

Visualization study of a flat confined loop heat pipe for electronic devices cooling

Effect of using acetone and distilled water on the performance of open loop pulsating heat pipe (OLPHP) with different filling ratios

Investigation on Transient Behaviors of Flat Plate Heat Pipes

Experimental investigation of a loop heat pipe with a flat evaporator and cupric oxide nanofluids as working fluid

Experimental Study of Loop Heat Pipes with Different Working Fluids in 190–260 K

Effect of geometries on the heat transfer characteristics of flat-plate micro heat pipes

Thermal performance comparison of flat plate pulsating heat pipes of different material thermal conductivity using ethanol-water mixtures

A Simple Model Used to Predict the Thermal Performance of Flat-Plate Closed-Loop Pulsating Heat Pipe