Abstract:Abstract Aim: Although most dental schools teach complete denture definitive impression techniques consisting of secondary impressions in border-molded custom impression trays, it has been found that later, graduates in clinical practice abandon this step because of its complexity and attempts to seek easier alternatives. To simplify two-stage techniques, single-step border molding with elastomeric impression materials and light-cured resin materials has gathered acceptance among clinicians. The study aims to evaluate the retention of record bases made with a modified single-stage impression technique that uses elastomeric impression material in a heat moldable tray with modeling compound as material for border molding. Settings and Design: This was an in vivo preliminary cohort study. Materials and Methods: Thirteen completely edentulous patients requiring complete dentures were included in the study. A traditional two-stage impression was made using custom trays fabricated over diagnostic casts and further border molding done with a modeling compound, and the final impression was made to use zinc oxide–eugenol impression material. Additionally, a modified single-stage impression technique using heat moldable impression trays was made. Master casts from each technique were made, and further record bases were made on each master cast. Wire loops were adapted on the palatal aspect of record bases. The retention of each record base was evaluated using a force gauge. Statistical Analysis: The Kolmogorov–Smirnov test was used to analyze the normality of variables and later Wilcoxon signed-rank test was applied. Results: The double-stage technique exhibited retention values in the range of 0.6–66.7 units, whereas the single-stage technique showed a range of 0.15–78.55. The tests showed no significant difference between double-stage and single-stage techniques ( P > 0.05). Conclusions: The single-stage technique using heat moldable trays with elastomeric impression material and modeling compound as a material for border molding can produce denture retention compared to the conventional technique that uses a two-step impression technique. The use of the modified single-stage technique can additionally save an extra appointment for patients, although it is better to use such a technique as an advanced impression technique and not as a training technique for beginners or students, as the material cost is substantially higher than the conventional two-stage technique.

Determination of the lingual border of lower complete dentures: How to use a silicone impression material?

Digital measurement method for comparing the absolute marginal discrepancy of three-unit ceramic fixed dental prostheses fabricated using conventional and digital technologies

Clinical application of the modified impression method for the lower complete denture

Relating the marginal fit of the castings to the accuracy of the impressions made from laminated hydrocolloid impression technique: a comparative study

Modified functional impression technique for complete dentures

A randomized controlled trial of the different impression methods for the complete denture fabrication: Patient reported outcomes

Influence of impression method and shoulder design on the marginal adaptation of CAD/CAM nanoceramic resin onlay restorations

Effect of Different Impression Techniques on Marginal Fit of Restoration – An In Vitro Study

Accuracy of Selective Laser Melted Bar retaining mandibular implant-assisted Overdenture: An In vitro Comparison of Different Impression Materials and Techniques

Digital evaluation of a simplified technique for resin splinting used for multiunit implant restoration impressions: An in-vitro comparative study

Digital analysis of fabrication accuracy and fit in additively and subtractively manufactured implant-supported fixed complete dentures

An Evaluation of Retention of Complete Denture Bases Made with a “Modified Single-stage Impression” Technique Using a Heat-moldable Tray

A preliminary study on the digital evaluation of absolute marginal discrepancy of fixed dental prostheses

Digital Evaluation of Trueness and Precision of Modern Impression Materials in Implant- Retained Mandibular Overdentures

Evaluation Of Adaptation Of The Polylactic Acid Pattern Of Maxillary Complete Dentures Fabricated By Fused Deposition Modelling Technology: A Pilot Study

Evaluation of a Novel 3D-Printed Custom Tray for the Impressions of Edentulous Jaws.

The internal and marginal adaptation of lithium disilicate endocrowns fabricated using intra and extraoral scanners: An in-vitro study

Cost-effectiveness analysis of two impression methods for the fabrication of mandibular complete dentures

Clinical study on the complete denture edge position and shape

In vivo evaluation of inter-operator reproducibility of digital dental and conventional impression techniques

Dimensional Accuracy of Novel Vinyl Polysiloxane Compared with Polyether Impression Materials: An In Vitro Study