Abstract:Modification of commercial carbon black. The dispersion of a filler in a rubber matrix is a crucial parameter affecting the mechanical and dynamical properties of a rubber compound. It is the current issue of the rubber compounding industry because, most fillers are categorized as a mineral, while the rubber is an organic material. The surface modification of the filler has been accepted as an effective technique for the improvement of the abovementioned parameter. First, the surface premodification of commercial carbon black with a grade of N660 (CB) was implemented by four different oxidation methods. After that, among of used methods, the oxidation method using citric acid was selected to produce modified carbon black (CB‐Oxi) for further treatment. Subsequently, the coupling agent, Bis[3‐(triethoxysilyl)propyl] tetrasulfide (TESPT) was functionalized on the surface of CB‐Oxi to produce modified‐CB‐Oxi. Also, for comparison purposes, the TESPT functionalization was accomplished on untreated CB to form modified‐CB. The FTIR spectra of CB‐Oxi showed using the premodification method introduced the hydroxyl and carboxyl groups on the surface of CB. The correspondent spectra for modified‐CB‐Oxi confirmed the existence of silane groups on the surface of the carbon black. However, the mentioned silane groups were not observed on the surface of modified‐CB. The findings were strengthened by several characteristic techniques including, FESEM, XRD, EDS, CHNS elemental analysis, and RAMAN spectra. The FESEM graphs and elemental mapping showed homogeneous dispersion and uniform distribution of sulfur and silicon elements on the modified‐CB‐Oxi surface. According to RAMAN spectra, the disturbance in the structure of carbon black graphite was reduced after surface modification. modified‐CB‐Oxi is proposed as a potential substitute filler for current commercial carbon black in rubber compounding.

Surface modification of iron powder with siloxane block copolymer and sodium dodecyl sulfate under wet ball milling

Surface Organic Modification of Magnetic Iron Oxide Black Particles

Surface Organic Modification of Fe 3 O 4 Magnetic Nanoparticles

Preparation of Polystyrene/Sio2 Composite Nanoparticles Bearing Sulfonic Groups on the Surface Via Emulsion Copolymerization Using A Polymerizable Emulsifier

Study on preparation and surface modification of precipitated silica obtained from fly ash

Anisotropic Sm–Fe–N Particles Prepared by Surfactant-Assisted Grinding Method

Research on Modification of Fe3O4 Magnetic Nanoparticles with Two Silane Coupling Agents

Enhancing Zero-Valent Iron (ZVI) Pulverization During Mechanical Milling: FeSx As Milling Aids

Surface Modification to Produce Hydrophobic Nano-Silica Particles Using Sodium Dodecyl Sulfate As a Modifier

The Effect of Surface Modification on the Microstructure and Properties of Γ-Fe2o3 Nanoparticles

Effects of Surface Modification by Liquids on Surface Group and Dispersibility of Si3N4 Powder

Influence of Surface Modification of Srfe12o19 Particles with Oleic Acid on Magnetic Microsphere Preparation

Surface modification of superfine SiC powders by ternary modifiers-KH560/sodium humate/SDS and its mechanism

Surface modification of commercial carbon black by silane coupling agents for improving dispersibility in rubber compounds

Surface modification of fly ash by mechano-chemical treatment

Microstructural Evolution During High Energy Ball Milling of Fe2o3-Sio2 Powders

Influence of surface active agent on the size of metal powder particles during their ball milling in a planetary mill

Surface Modification of CaCO3 by Ultrasound-Assisted Titanate and Silane Coupling Agents

Effect of Surface Modified Foamed Fe Powder on Tribological Properties of Semi-Metallic Friction Material

Synthesis and Surface Modification of a Rod Shaped Nanometer gamma-Al2O3

Preparation and Surface Modification of Fe<sub>3</sub>O<sub>4 &Lt;/sub>nano-Magnetic Powders