Abstract:<p>Imaging surface deformation of a coupon specimen in micro‐tensile testing with an optical microscope presents challenges due to the narrow depth of field (DoF) of optical microscopes. Materials being heterogeneous at microscopic length scale, the sample surface deforms into a complex 3D surface texture, evolving continuously as the loading increases. Because of the narrow DoF, the region that is in focus within the field of view (FoV) decreases substantially in size with the increasing out‐of‐plane heterogeneous deformation. To address this challenge, a method based on image blending and stabilization of the captured image frames is proposed. Image blending combines the partial regions that are in focus from a set of successive image frames captured at different working distances from the object surface plane to construct a single image that has a large part of the FoV in focus. The blended images are then obtained at different levels of macroscopic strains, i.e. the global homogeneous strain, in order to characterize the evolution of the heterogeneous deformation. The image stabilization removes any misalignments of the blended images by spatially realigning them choosing a common feature as a reference point. The validation of the proposed method with conventionally and additively manufactured stainless steel 316L (SS 316L) specimens demonstrates excellent improvement in image quality. Almost 100% of the FoV is maintained in focus regardless of the amount of out‐of‐plane heterogeneous deformation caused during tensile testing, which is quite remarkable for optical microscopy imaging. Consequently, the blended and stabilized images enhanced the accuracy of digital image correlation (DIC). Time‐lapse videos of the deformation generated using these images captured the evolution of the slip bands and their transmission through twinning boundaries in the stainless steel microstructure. Overall, this study demonstrates the feasibility of using image‐processing techniques to advance optical microscopy to image complex 3D surfaces evolving with time.</p><p>This article is protected by copyright. All rights reserved</p>

In-Situ Electron Channeling Contrast Imaging under Tensile Loading: Residual Stress, Dislocation Motion, and Slip Line Formation

Insights into fundamental deformation processes from advanced in situ transmission electron microscopy

Observation and quantitative analysis of dislocations in steel using electron channeling contrast imaging method with precise control of electron beam incident direction

Fundamental and experimental aspects of diffraction for characterizing dislocations by electron channeling contrast imaging in scanning electron microscope

Surface Patterning for Multi-Scale Strain Analysis of In-Situ Sem Mechanical Experiments

Transmission Electron Microscope In Situ Straining Technique to Directly Observe Defects and Interfaces During Deformation in Magnesium

In-situ Transmission Kikuchi Diffraction Nano-tensile Testing

Surface Patterning for Combined Digital Image Correlation and Electron Backscatter Diffraction In-Situ Deformation Experiments

In situ transmission electron microscopy investigation of electroplasticity in single crystal nickel

Pulsating Propagation of Strain-Localized Band in Plastic Deformation of an Al-Alloy Sample Observed by Electronic Speckle Pattern Interferometry(Optical Method 2)

Elastodynamic Behaviors of Steady Moving Straight Dislocation Within Thin Nano Film

Nanomechanical Characterization of Metallic Materials

Intermitted 3D diffraction tomography combined with in situ Laue diffraction to characterize dislocation structures and stress fields in micro bending cantilevers

Investigation of Grain Subdivision at Very Low Plastic Strains in A Magnesium Alloy

A Technique for In-Situ Displacement and Strain Measurement with Laboratory-Scale X-Ray Computed Tomography

Deformation Fields Measurement of Crack Tip under High-Frequency Resonant Loading Using a Novel Hybrid Image Processing Method

High‐resolution optical microscopy for characterising microstructural deformation in microtensile testing

In situ measurement of three-dimensional intergranular stress localizations and grain yielding under elastoplastic axial-torsional loading

Investigation on Mechanism of Plastic Deformation by Digital Speckle Pattern Interferometry

In-situ Study of Microstructural Evolution and Local Strain Distribution During Tensile Loading of Near-Micrometre Grain Size Aluminium