Abstract:The formation of the surface layer of cast iron during the processing of cast iron in the environment of superheated steam of an aqueous solution of salts is considered. An ecologically cleaner method of chemical-thermal treatment is offered. The article considers the surface layer obtained in the environment of superheated steam of an aqueous solution of water-soluble salts of ammonium molybdic acid. The layer is formed on the surface of the matrix and around the graphite inclusions. The impact of temperature on the formation of a multilayer coating by increasing the temperature in contact with the metal surface is the dissociation of chemical compounds in solution, with the formation of atomic oxygen, sulfur, nitrogen, molybdenum. The formation of the surface layer occurred not only on a metal base, but also on the boundaries of graphite, both lamellar and globular, coming to the surface of the metal without breaking the solid layer. It is established that as a result of interaction of technological parameters of temperature, holding time and concentration of saturated medium graphite in the surface layer changes its shape, becoming spherical, although in the matrix it had a lamellar shape. It is multiphase and contains soft and hard structural components. Comparative studies have shown that the wear rate of untreated cast iron is much higher than that of treated cast iron, and reaches 0.8 ∙ 10-4 μm/km at a load of 400 N. This increases the wear resistance of cast iron and at the same time improves the workability reducing the coefficient of friction. The effect of the coating on the workability show that the stabilization of the friction moment occurs faster in samples with a multilayer coating. Thus, for gray cast iron with lamellar graphite, the stabilization time of the friction moment in a multilayer coating is 0.6 h compared with 2 h for a single layer coating; in high-strength cast iron it is, respectively, 5.2 and 6.3 hours.

The Effect of Heating Time and Heating Temperatures to Layer Thickness and the Glossiness Level of a Surface in Blackening Coating Process

Effects of Heat Treatment on Structure Transformation of Cr/Al Composite Coatings

The effect of pre-heat and post-heat treatment on the hardness and blackening process of electroless NiP deposits on titanium alloy

Effects of Heat Treatments on Phase Structure of Electrodeposition Aluminum Coatings on Different Substrates

Mathod and Performance of Blackening Mild Steel with Water Vapor in Nitrogen Environment

Pengaruh Arus Dan Waktu pelapisan hard chrome terhadap ketebalan lapisan dan tingkat kekerasan mikro pada plat baja karbon rendah aisi 1026 dengan menggunakan cro3 250 gr/lt dan h2so4 2,5 gr/lt pada proses elektroplating

Analysis of Blackening Reaction of Zn-Mg-Al Alloy-Coated Steel Prepared by Water Vapor Treatment

Optimization of Black Nickel Coatings’ Electrodeposit onto Steel

Thermodynamics and Kinetics of Borochromized Coatings Prepared on 5CrNiMo Steel by Thermo-Reactive Diffusion

Growth Kinetics and Microstructure of Composite Coatings on H13 by Thermal Reactive Diffusion

Increasing the tribological properties of the sur-face layer of cast iron by treatment in the envi-ronment of overheated steam of aqueous solution

The Enhancement Effect of Salt Bath Chromizing for P20 Steel

Microstructure, mechanical and erosion wear analysis of post heat treated iron alloy based coating with varying chromium

Thermal degradation of black chrome coatings

Effect of heating temperature on the behavior of reinforced zinc-rich coating with nanoparticles

High Temperature Oxidation Behaviors of Ni-Cr Based Thermal Sprayed Coatings

Preparation of Metal Coatings on Steel Balls Using Mechanical Coating Technique and Its Process Analysis

On the Effect of the Duration of Microarc Oxidation on the Characteristics of Thermal-Control Coatings on Aluminum Alloy

Growth Process and Mechanism of Hot-Dip Galvanised Zn–5Al Coating on Steel

Effect of Heat Treatment on Chemical Plating of Ni-Cr-P on 65Mn Alloy Steel

Relationship between Texture, Hydrogen Content, Residual Stress and Corrosion Resistance of Electrodeposited Chromium Coating: Influence of Heat Treatment