Abstract:Despite recent advances and improvements in modeling and prediction of the dynamics of the machining process, an efficient machining process is limited due to chatter and instability of machining system. In fact, the machining system contains various kinds of joints, which cause difficulties in dynamics modeling, simulation and prediction. Moreover, the flexible support system results in large deformation and violent vibration of the workpiece when machining, and the thin-walled workpiece easily gives rise to the chatter of the machining system. Therefore, the dynamics of the flexible support system was considered to calculate stability lobe diagram in the modeling of milling process. The whole machining system was regarded as a closed loop composed by the machine tool structures, support, workpiece and machining process. In this paper, the receptance coupling (RC) method was introduced to predict the dynamics of the closed machining system. A milling process was taken for example to predict the chatter limitations using the dynamics of closed model. The mathematical model of the machining system (machine tool structures, spindle, holder and tool), together with the details of joint contacts, was given based on the RC method. The RC model was used to obtain the dynamics of the system, while receptance of the tool point was coupled. Based on the coupling model of the machining system, the depth limitations under different speeds were estimated for the technology parameter optimization in milling process. The response was considered to be the sum of the cutting point and the support system. The flexibility of the support system was considered to be the feedback of the cutting stiffness. By this means, the traditional model was modified to calculate the stability lobe diagram based on the dynamics of the spindle and support system. Furthermore, the milling experiment was carried out to verify the prediction results, and the dominant natural frequencies of receptance at tool point were obtained by modal testing to define the stability lobe diagram. It was found that the chatter results matched well with the stability lobes. It was concluded that the support system with poor stiffness might cause violent chatter especially when the workpiece was thin-walled. The cutting depth limitations of the flexible support system were lower than that of the rigid one. Moreover, this closed model of the machining system is appropriate for the chatter prediction of the flexible support system or thin-walled workpiece, so it is helpful for a better parameter optimization.

Optimal milling modes identification of a jet-engine blade using time-domain technique

Experimental and simulation study on chatter stability region of integral impeller with non-uniform allowance.

Chatter Avoidance by Spindle Speed and Orientation Planning in Five-Axis Ball-End Milling of Thin-Walled Blades

Feasible spindle speed interval identification method for large aeronautical component robotic milling system

Sensitivity Analysis and Monte Carlo Based Uncertainty Quantification of the In-process Modal Parameters in Milling

Dynamics Modeling-Based Optimization of Process Parameters in Face Milling of Workpieces with Discontinuous Surfaces

Dynamic Modeling for Chatter Analysis in Micro-Milling by Integrating Effects of Centrifugal Force, Gyroscopic Moment, and Tool Runout

Optimum Selection of Variable Pitch for Chatter Suppression in Face Milling Operations

Modeling dynamics and stability of variable pitch and helix milling tools for development of a design method to maximize chatter stability

A Novel Approach for Chatter Online Monitoring Using Coefficient of Variation in Machining Process

Modal parameter identification of general cutter based on milling stability theory

Chatter Stability Prediction of Ball-End Milling Considering Multi-Mode Regenerations

Investigation of a cutting state-independent method for identifying in-process frequency response functions of the micro milling system

Position-dependent milling process monitoring and surface roughness prediction for complex thin-walled blade component

Investigation on an in-process chatter detection strategy for micro-milling titanium alloy thin-walled parts and its implementation perspectives

Chatter suppression analysis for variable pitch cutter in milling

An Improved Tool Path Model Including Periodic Delay for Chatter Prediction in Milling

Operational Modal Analysis of CNC Machine Tools Based on Flank-Milled Surface Topography and Cepstrum

Intra-wave Modulations in Milling Processes

An intelligent milling chatter detection method based on VMD-synchro-squeeze wavelet and transfer learning via deep CNN with vibration signals

Stability Prediction of Milling Process with Closed Machining System Dynamics with Flexible Thin-Walled Workpiece