Abstract:In some circumstances, hybrid polymer microfluidic chips composed of both elastic, gas-permeable polydimethylsiloxane (PDMS) and rigid plastics are needed. However, it is quite difficult to bond PDMS irreversibly to plastics such as polystyrene (PS). In this article, a facile method for irreversible bonding of PDMS to PS was proposed based on UV/O-3-assisted surface modification in combination of surface silanization. Firstly, a PS sheet was exposed to UV/O-3 to produce oxygen-containing polar moieties, such as hydroxyl and carboxylic acid, on its surface. Secondly, the UV/O-3 treated PS sheet was silanized with (3-aminopropyl)triethoxysilane (APTES) via the reaction between the oxygen-containing polar moieties on the PS surface and the molecules of APTES. Thirdly, the silanized-PS sheet and the PDMS substrate with micro channel network were treated with UV/O-3 again to generate silanol moieties on both surfaces. Finally, the UV/O-3 treated PDMS was immediately brought intimate contact with the UV/O-3 treated silanized-PS, and irreversible bonding of PDMS with PS occurred after putting the PDMS-PS complex at room temperature for 1 h through the condensation reaction between silanol moieties. Contact angle measurement, X-ray photoelectron spectroscopy, total reflection Fourier transformation infrared spectrometer were applied to characterize the surface chemistry of the PS during the UV/O-3 treatment and silanization. The hybrid PDMS-PS microfludic chips prepared with the established method can bear a gas pressure higher than 0.5 MPa and a water stream at a flow rate higher than 170 mu L/min (the test channels were 2.5 cm in the length, 50 mu m in the width, 200 mu m in the depth). A hybrid PDMS-PS microfluidic chip composed of gas-permeable PDMS substrate with channel network and excellently biocompatible PS cover sheet was fabricated for cell culture. The experimental results showed that HeLa cells cultured in the hybrid PDMS-PS microchip grew much better than those cultured in the full PS microchip, and slightly better than those in the full PDMS microchip.

Argon–water DBD pretreatment and vapor‐phase silanization of silica: Comparison with wet‐chemical processes

Bulk Polymerization of Acrylic Acid Using Dielectric-Barrier Discharge Plasma in a Mesoporous Material.

Polymerization of Sodium 4-Styrenesulfonate Inside Filter Paper Via Dielectric Barrier Discharge Plasma

The Fabrication of Superlow Protein Absorption Zwitterionic Coating by Electrochemically Mediated Atom Transfer Radical Polymerization and Its Application

Treatment of PDMS surfaces using pulsed DBD plasmas: comparing the use of different gases and its influence on adhesion

Plasma Polymerization at Atmospheric Pressure with a New Type of DBD Reactor for Combinatorial Studies: Classification of Precursor Concentration Dependencies

An Approach for Irreversible Bonding of PDMS-PS Hybrid Microfluidic Chips at Room Temperature

Solution-phase Surface Modification in Intact Poly(dimethylsiloxane) Microfluidic Channels.

Transferred plasma jet from a dielectric barrier discharge for processing of poly(dimethylsiloxane) surfaces

Influence of Gas Type on Reactive Species Formation, Antimicrobial Activity, and Cytotoxicity of Plasma-Activated Water Produced in a Coaxial DBD Reactor

The stability of radio-frequency plasma-treated polydimethylsiloxane surfaces

Visualization of In Situ Oxidation Process Between Plasma and Liquid Phase in Two Dielectric Barrier Discharge Plasma Reactors Using Planar Laser Induced Fluorescence Technique

Investigation of Cold Atmospheric Plasma Treatment in Polydimethylsiloxane Microfluidic Devices with a Transmural Method

Theoretical-Computational Study of Atmospheric DBD Plasma and Its Utility for Nanoscale Biocompatible Plasmonic Coating

Enhancing silk fibroin structures and applications through angle-dependent Ar+ plasma treatment

A comparative study of dielectric barrier discharge plasma device and plasma jet to generate plasma activated water and post-discharge trapping of reactive species

Atmospheric pressure dielectric barrier discharge plasma for in-situ water treatment using a bubbling reactor

Design and development of medium-pressure plasma process for optical substrate finishing: A comparative study with wet chemical etching

Mesoporous Silica Thin Films Prepared by Argon Plasma Treatment of Sol–gel-Derived Precursor

Spatial resolution in thin film deposition on silicon surfaces by combining silylation and UV/ozonolysis

The enhancing energy efficiency of sulfadiazine degradation using a DBD-contact plasma treatment process