Abstract:Semi-solid thixoforming processes rely on a material microstructure made of globular solid grains more or less connected to each other, thus developing a solid skeleton deforming into a liquid phase. During processing, the material structure changes with the processing history due to the agglomeration of the particles and the breaking of the grains bonds. This particular evolutive microstructure makes semi-solid materials behave as solids at rest and as liquids during shearing, which causes a decrease of the viscosity and of the resistance to deformation while shearing. Thixoforming of aluminum and magnesium alloys is state of the art and a growing number of serial production lines are in operation all over the world. But there are only few applications of semi-solid processing of higher melting point alloys such as steel. This can partly be attributed to the high forming temperature combined with the intense high temperature corrosion that requires new technical solutions. However the semi-solid forming of steels reveals high potential to reduce material as well as energy consumption compared to conventional process technologies, such as casting and forging. Simulation techniques exhibit a great potential to acquire a good understanding of the semi-solid material process. Therefore, this work deals with the development of an appropriate constitutive model for semi-solid thixoforming of steel. The constitutive law should be able to simulate the complex rheology of semi-solid materials, under both steady-state and transient conditions. For example, the peak of viscosity at start of a fast loading should be reproduced. The use of a nite yield stress is appropriate because a vertical billet does not collapse under its own weight unless the liquid fraction is too high. Furthermore, this choice along with a non-rigid solid formalism allows predicting the residual stresses after cooling down to room temperature. Several one-phase material modeling have been proposed and are compared. Thermomechanical modeling using a thermo-elasto-viscoplastic constitutive law has been developed. The basic idea is to extend the classical isotropic hardening and viscosity laws to the non solid state by considering two non-dimensional internal parameters. The rst internal parameter is the liquid fraction and depends on the temperature only. The second one is a structural parameter that characterizes the degree of structural build up in the microstructure. Those internal parameters can depend on each other. The internal parameters act on the the viscosity law and on the yield surface evolution law. Di erent formulations of viscosity and hardening laws have been proposed and are compared to each other. In all cases, the semi-solid state is treated as a particular case, and the constitutive modeling remains valid over the whole range of temperature, starting from room temperature to above the liquidus. These models are tested and illustrated by mean of several representative numerical applications.

Transient Thermo-mechanical Analysis of Steel Ladle Refractory Linings Using Mechanical Homogenization Approach

Thermomechanical behavior of alumina–magnesia castables and numerical modeling of the steel ladle thermal process

A Multi-Phase Model for Transformation Plasticity Using Thermodynamics-Based Metallurgical Algorithm

Thermomechanical finite element modeling of steel ladle containing alumina spinel refractory lining

Continuous Casting Mould for Square Steel Billet Optimised by Solidification Shrinkage Simulation

Numerical Simulation of Transient Flow and Heat Transfer in a Steel Ladle During Holding Period

Steel Ladle Slag Zone Lining Optimization Considering Irreversible Material Behavior

A simple yet consistent constitutive law and mortar-based layer coupling schemes for thermomechanical macroscale simulations of metal additive manufacturing processes

Numerical Simulation of Fluid Flow and Heat Transfer in a Ductile Iron Ladle During Holding and Teeming

A Hierarchical Theoretical Model for Mechanical Properties of Lath Martensitic Steels

Mathematical modelling of fluid flow, heat transfer and solidification phenomena in continuous casting of steel

Numerical Simulation of Heat Transfer Phenomenon in Steel Making Ladle

Analysis of Thermo-fluidic and Phase Change Behaviour of Liquid Steel in a Continuous Billet Caster Mould: Effect of Casting Speed

Phase field model for coupled displacive and diffusive microstructural processes under thermal loading

Numerical derivation of homogenised constitutional relation of mortar-less interlocking brick wall for dynamic response prediction

Semi-solid constitutive modeling for the numerical simulation of thixoforming processes.

Using Abaqus User Subroutines to Develop a New Finite Element Modeling Tool for Heat Treatment Simulation

3D Transient Heat Transfer Simulation and Optimization for Initial Stage of Steel Continuous Casting Process

Numerical Simulation on Austenitization of Cast Steel During Heating Process

A machine learning based material homogenization technique for in-plane loaded masonry walls

Development of a thermo-mechanically coupled crystal plasticity modeling framework: application to polycrystalline homogenization