Abstract:Fluid viscosity is one of the key factors affecting the cavitation characteristics of the Helico-axial Multiphase Pump (HAMP). In this paper, fluids with viscosities of 24.46 mm2/s, 48.48 mm2/s, 60.70 mm2/s, and 120.0 mm2/s were investigated by numerical simulation. The Ansys Fluent software was employed to conduct the simulation. The mixture multiphase flow model and the RNG k-ε turbulence model were adopted. The Singhal cavitation model was employed to consider the effects of the non-condensable gas on cavitation. An experiment was carried out to validate the numerical method. The results showed that the Net Positive Suction Head-available (NPSHA) of the pump decreased as the fluid viscosity increased. Under the critical NPSHA condition, the NPSHA decreased from 5.11 m to 3.68 m as the fluid viscosity increased from 24.46 mm2/s to 120.0 mm2/s. This suggested that the cavitation performance of the pump was deteriorated under high fluid viscosity. The impeller passage area occupied by the vapor increased when the fluid viscosity increased. Nearly half of the flow passages were occupied by cavitation bubbles when the fluid viscosity increased to 120.0 mm2/s. The vapor volume fraction, both on the suction surface and pressure surface of the blade, increased with the fluid viscosity. The vapor on the suction surface was mainly distributed in the region with the streamwise between 0 and 0.36 when the fluid viscosity was 24.46 mm2/s; while the high vapor volume fraction range increased to the streamwise of 0.42 when the fluid viscosity increased to 120.0 mm2/s. The higher vapor volume fraction corresponded with the lower pressure. It was also found that the turbulent kinetic energy, both on the suction surface and pressure surface, increased with the fluid viscosity, which was the favorite for producing more cavitation bubbles. Furthermore, the maximum velocity area was mainly concentrated in the inlet area of the impeller. The velocity distribution in the impeller was basically the same with the viscosity of 24.46 mm2/s and 48.48 mm2/s. When the viscosity further increased to 60.70 mm2/s, the maximum velocity area in the impeller was relatively large. This study provides a reference for designing the HAMP.

The impact of viscosity and propagation velocity of the flow on the initiation of the cavitation in a gear pump

Numerical Study of the Hydrodynamics of an External Gear Pump

Fluid analysis of the cavitation of the microsegment gear pump operating at high-pressure condition

Dynamic Simulation Research on Cavitation in Internal Multi-connected Volumes of Gear Pump

New Method to Determine the Dynamic Fluid Flow Rate at the Gear Pump Outlet

Influence of Fluid Viscosity on Vortex Cavitation at a Suction Pipe Inlet

Research on Cavitation Characteristics and Influencing Factors of Herringbone Gear Pump

Effect of cavitation on leakages through active contact of involute toothed external gear pump

Dynamic Behaviors of Blade Cavitation in a Water Jet Pump with Inlet Guide Vanes: Effects of Inflow Non-Uniformity and Unsteadiness

Influence of the Rotation Speed on the Internal Flow Characteristics of an Aircraft Fuel Gear Pump

Development of a Numerical Approach for the CFD Simulation of a Gear Pump under Actual Operating Conditions

Influence of Fluid Viscosity on Cavitation Characteristics of a Helico-Axial Multiphase Pump (HAMP)

Effects of pump parameters on the oil absorption characteristics of bidirectional involute internal gear pumps

Study of the Cavitation Phenomenon Inside Roller Vane Pump

Numerical Simulation of the Cavitation Characteristics of A Mixed-Flow Pump

Cavitation Performance Improvement of High Specific Speed Mixed-Flow Pump

Fundamentals of cavitation and bubble dynamics with engineering applications

Numerical investigation of vibration-induced cavitation for gears considering thermal effect

Visualization study of the flow processes and phenomena in the external gear pump

Influence of impeller-tongue interaction on the unsteady cavitation behavior in a centrifugal pump