Abstract:The poly(vinylidene fluoride) (PVDF) as-spun fibers with different spin-stretching ratios were fabricated via melt-spinning method using plunger spinning machine. PVDF fibers with different post-stretching ratios were subsequently obtained by post-stretching method under the thermal treatment condition. The crystal and orientation structure of the fibers were investigated by X-ray diffraction (XRD), differential scanning calorimetry (DSC), polarizing optical microscopy (POM) and so on. The results indicated the orientation of alpha crystal and macromolecular increased with the increasing spin-stretching ratio. Furthermore, as the higher spinstretching ratio increased, the degree of crystallinity of as-spun fiber was prone to perfection. Furthermore, according to the POM photomicrograph, the horizon of extinction position was almost entirely black, and the horizon of diagonal position was getting brighter, due to the increase of the anisotropy of as-spun fibers. This was attributed that the irregular fiber macromolecules were stretched to regular structure. When spin-stretching ratio was 330, the crystallinity of as-spun fiber could reach 56.38% and the orientation factor of alpha(110/200) crystal plane was up to 0.89. In terms of post-stretching technique, the stretching ratios had no significant influence on the degree of crystallinity However, the post-stretching process played a positive role in the transition of the crystal phase from alpha to beta. The molecular chains of the fibers are easier to slip and arrange regularly along the fiber axis during spin-stretching process. The conformation was easier to transfer from alpha phase to beta phase owing to the segmental motion of molecular chains during post-stretching process. Especially, the orientation of beta crystal was also improved at the same time. Specially, when the post-stretching was up to the stage of uniform reduction of fiber diameter, the orientation of beta crystal retained a high level. When post-stretching ratio was 11, the content of beta crystal could account for 82.85% and the orientation factor of beta(110/200) crystal plane was up to 0.83.

Effects of Melt-Spinning Speed on Structure Development of Polypropylene Fiber After Necking

The evolution of crystalline structures during gel spinning of ultra-high molecular weight polyethylene fibers

Fiber Formation and Structural Development of HBA/HNA Thermotropic Liquid Crystalline Polymer in High-Speed Melt Spinning

Numerical Study of Melt-Spinning Dynamic Parameters and Microstructure Development with Ongoing Crystallization

Deformation Mechanisms of Polymer Thin Films by Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism and Macroscopic Stress. 2. Molecular Orientation During Necking Process of Isotactic Polypropylene

Effect of Die-Swell Ratio on Polyacrylonitrile As-Spun Fiber Formation

Optimization of hot drawing process of ultra‐high molecular weight polyethylene monofilament prepared by melt spinning

Tensile strength of polyester fiber estimated by molecular-chain extension prior to structure formation

Application of an Interpenetrating Network Model to the Necking in the Microcrystalline Region in Four Annealed Isotactic Polypropylene Films Subjected to Uniaxial Stretching at Room Temperature

Effect of Jet Stretch on Polyacrylonitrile As‐spun Fiber Formation

Preparation, mechanical properties and microstructure of polyoxymethylene fiber through melt spinning and hot drawing by using injection-molding grade resins

Inhomogeneous Deformation of Microcrystalline Region in Isotactic Polypropylene Film Revealed by A Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism and Macroscopic Stress

The influence of formation temperatures on the crystal structure and mechanical properties of ultrahigh-molecular-weight polyethylene/high-density polyethylene-blend fibers prepared by melt spinning

Effects of Spinodal Decomposition on Mechanical Properties of A Polyolefin Blend from High to Low Strain Rates

Numerical Simulation Of Fiber Spinning Process With Structure Evolution Of Polymer Chains

Effect of Coagulation Bath Concentration on the Structure and Properties of Polyacrylonitrile As-Spun Fibers During Wet-Spinning

Numerical Simulation and Experimental Verification of Melt-Spinning Parameters' Effects on Multi-Leaf Hollow-Profiled Fiber Preparation

Effect of drawing and heat‐setting process on aggregate structure of Poly(ethylene terephthalate) industrial fiber in large‐scale spinning production

Melt spining – a special process of thermoplastic processing and structure formation

Crystalline Structure Changes of Poly(vinylidene fluoride) Fibers during Stretching Process

Microstructural Evolution during Dry-Jet Wet Spinning Postprocessing from Coagulation Bath Fiber to High-Performance Polyacrylonitrile Precursor Fiber