Abstract:Abstract Metal-composite laminates and joints are applied in aircraft manufacturing and maintenance (repairing) using aluminum alloys (AA) and glass fiber-reinforced polymer (GFRP). In these applications, drilling has a prominent place due to its vast application in aeronautical structures’ mechanical joints. Thus, this study presents the influence of uncoated carbide drills (85C, 86C, H10N), cutting speeds ( v c = 20, 40, and 60 m min −1 ), and feed rates ( f = 0.05, 0.15, and 0.25 mm rev −1 ) on delamination factor, thrust force ( F t {F}_{\text{t}} ), and burr formation in dry drilling metal-composite laminates and joints (AA2024/GFRP/AA2024). Experiments were performed, analyzed, and optimized using the Box–Behnken statistical design. Microscopic digital images for delamination evaluation, piezoelectric dynamometer for thrust force acquisition, and burr analysis were considered. The major finding was that the thrust force during drilling depends significantly on the feed rate. Another significant factor was the influence of the drill type (combined or not with feed rate). In fact, it was verified that the feed rate and the drill type were the most significant parameters on the delamination factor, while the feed rate was the most relevant on thrust force. The cutting speed did not affect significantly thrust force and delamination factor at exit ( F da S ) \hspace{.25em}({F}_{{\text{da}}_{\text{S}}}) . However, the combination f × v c was significant in delamination factor at entrance ( F da E ) \text{ }({F}_{{\text{da}}_{\text{E}}}) . Based on the optimized input parameters, they presented lower values for delamination factors ( F da E = 1.18 {F}_{{\text{da}}_{\text{E}}}=1.18 and F da S = 1.33 {F}_{{\text{da}}_{\text{S}}}=\hspace{.25em}1.33 ) and thrust force ( F t = 67.3 N {F}_{\text{t}}=67.3\hspace{.5em}\text{N} ). These values were obtained by drilling the metal-composite laminates with 85C-tool, 0.05 mm rev −1 feed rate, and 20 m min −1 cutting speed. However, the burrs at the hole output of AA2024 were considered unsatisfactory for this specific condition, which implies additional investigation.

Multiple Sensor Monitoring of CFRP Drilling to Define Cutting Parameters Sensitivity on Surface Roughness, Cylindricity and Diameter

Experimental Analysis and Application of a Multivariable Regression Technique to Define the Optimal Drilling Conditions for Carbon Fiber Reinforced Polymer (CFRP) Composites

A New Strategy of Carbon Fiber Reinforced Plastic Drilling Evaluation Using Thermal Measurement

Hole Diameter Variation and Roundness in Dry Orbital Drilling of Cfrp/Ti Stacks

Study on Robot Automatic Drilling of Carbon Fiber Reinforced Plastics (CFRP)

Factor Analysis of Machining Parameters of Fiber-Reinforced Polymer Composites Based on Finite Element Simulation with Experimental Investigation

Cutting force and hole quality analysis in micro-drilling of CFRP

A Unified Geometrical Modeling and Analysis Method for Evaluating CFRP Machining Performance: Cutting Geometry Space

Smart Multi-Sensor Monitoring in Drilling of CFRP/CFRP Composite Material Stacks for Aerospace Assembly Applications

Modeling Evolution of Cutting Force in Ultrasonically Assisted Drilling of Carbon Fiber Reinforced Plastics

Combined analysis of wear mechanisms and delamination in CFRP drilling

CFRP drilling process control based on spindle power consumption from real production data in the aircraft industry

Design and Analysis of CFRP Drilling by Electrical Discharge Machining

Influence of Machining Condition and Nano-Graphene Incorporation on Drilling Load and Hole Quality in Both Conventional Drilling and Ultrasonic-Assisted Drilling of CFRP

Optimizing Process Parameters in Drilling of CFRP Laminates: A Combined MOORA–TOPSIS–VIKOR Approach

Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks

Optimization for drilling process of metal-composite aeronautical structures

Optimization of Drilling Parameters on Delamination and Burr Formation in Drilling of Neat CFRP and Hybrid CFRP Nano-Composites

Machinability Of Drilling T700/Lt-03a Carbon Fiber Reinforced Plastic (Cfrp) Composite Laminates Using Candle Stick Drill And Multi-Facet Drill

Effect of Drilling Parameters and Tool Geometry on the Thrust Force and Surface Roughness of Aerospace Grade Laminate Composites

A Drilling Case Study in Polymer Composites Reinforced by Virgin and Recycled Carbon Fibres (CFRP and Rcfrp) to Analyse Thrust Force and Torque