Abstract:It has been long understood that fretting differs from sliding wear in that the relative displacement between the bodies is generally smaller than the size of the contact between them, with debris ejection from the contact thus playing an important role in the behaviour of the contact in fretting. Whilst these ideas were clearly articulated more than 30 years ago via Godet's third-body approach and Berthier's concept of the tribology circuit, calculation of wear rates in fretting have continued to employ Archard's wear equation (or approaches directly derived from it), despite this approach assuming that the rate of wear is controlled by the rate of generation of wear debris (as opposed to the rate of its ejection from the contact). It has been shown recently that when debris ejection is the rate-determining-process in fretting, the instantaneous rate of wear is inversely proportional to a characteristic dimension of the wear scar. When non-conforming specimen pair geometries (such as cylinder-on-flat) are employed in fretting testing, the wear scar size increases as wear proceeds, and thus the instantaneous rate of wear decreases. In this paper, wear equations have been derived for three commonly employed non-conforming pair specimen geometries, which all take the form <math>Vw=KRn−1Edn</math> (<math>Vw</math> is the wear scar volume, <math>R</math> is the radius of the non-plane specimen(s) in the pair and <math>Ed</math> is the frictional energy dissipated) where <math>n</math> varies between 0.67 and 0.8 depending upon the geometry and assumptions made regarding the governing equation. It is argued that the assumptions on which the analysis is based are most valid for the cylinder-on-flat contact configuration with fretting perpendicular to the cylinder axis where the length of the line contact is large compared to the wear scar width. It is demonstrated that, despite the often apparently good fit of experimental data to an Archard-type equation, it is not appropriate to employ such Archard-type approaches to the analysis of fretting data in situations where debris ejection is the rate-determining-process. The equations derived in this paper relating wear scar size to some measure of the duration of the test should be used for such analysis instead of the linear relationships generally employed in previous work.

The final NO-WEAR state due to dual-mode fretting: Numerical prediction and experimental validation

+Fretting wear: A phenomological approach

Electrical contact resistance endurance of AgNi10 alloys under fretting wear: Experiment and numerical prediction

Experimental and numerical study on the fretting wear-fatigue interaction evolution in press-fitted axles

Finite element analysis of fretting wear considering variable coefficient of friction

Experimental and computational investigation of fretting fatigue characterized by nominal contact pressure in dovetail structures

Study of fretting wear mechanisms of complete contacts

Modeling adhesive and abrasive wear phenomena in fretting interfaces: A multiphysics approach coupling friction energy, third body and contact oxygenation concepts

Contact size and debris ejection in fretting: The inappropriate use of Archard-type analysis of wear data and the development of alternative wear equations for commonly employed non-conforming specimen pair geometries

Identification between rotational fretting and rotational wear of PMMA/steel by means of tribo-noise and tribo-vibration signals

Fracture Mechanics Assessment of Stress Concentrations in Incomplete Fretting Contacts

An experimental investigation of adhesive wear extension in fretting interface: application of the contact oxygenation concept

A computationally efficient method for the prediction of fretting wear in practical engineering applications

On the Possibility of Frictional Damping with Reduced Wear: A Note on the Applicability of Archard's Law of Adhesive Wear under Conditions of Fretting

Simulation of fretting wear in steel wires under variable coefficient of friction and variable wear coefficient

Numerical Study on Fretting Wear of DZ125/FGH99 Tenon/Mortise Joint Structure

A multilayer nodes update method in FEM simulation of large depth fretting wear

A coupled approach to model the effect of wear on the dynamics of the shrouded bladed disk

A Debris Layer Evolution-Based Model for Predicting Both Fretting Wear and Fretting Fatigue Lifetime

Modification methodology of fretting wear in involute spline

Wear and Airborne Noise Interdependency at Asperitical Level: Analytical Modelling and Experimental Validation