Abstract:The present work considers a shell-and-coil heat exchanger, and the hybrid nanofluid's flow and heat transfer inside the proposed thermal system are numerically evaluated. The coil tube has a conical pattern and is oriented horizontally inside the shell. Three water-based hybrid nanofluids are considered here as heat transfer fluids. A commercial CFD code that uses the finite volume method performs the numerical analysis. The regime of fluid flow is turbulent in both coil and shell sections. The validation analysis of the present numerical model was performed using the experimental results of the reference, and accordingly, the accuracy of the present numerical model was proved. This work includes two sectors. In the first part, the volume concentration of the considered hybrid nanofluid was kept constant, and the influence of the hybrid nanofluid kind on the hydrothermal behaviour of the shell-conical-coil heat exchanger was evaluated numerically. In this section, three hybrid nanofluids, (i) Water/MgO–TiO 2 , (ii) Water/MOS 2 -CuO, and (iii) Water/Ag-HEG, were employed. Also, for all suggested hybrid nanofluids, the volume concentration of both employed nanoparticles are equal to each other, φ 1 = φ 2 . The obtained outcomes depicted that between various considered heat transfer fluids, the Water/MgO–TiO 2 model displayed the most outstanding thermal performance value in all the investigated Dean numbers, and the model Water/MOS 2 -CuO was in second place. Moreover, the maximum thermal performance for the hybrid nanofluid was obtained at φ 1 = φ 2 = 0.7. The Ag-HEG/Water and MgO–TiO 2 /Water hybrid nanofluids have the lowest and maximum thermal performance at the lowest considered Dean number among the evaluated hybrid nanofluids. As a result, the MgO–TiO 2 /Water hybrid nanofluid has roughly 18.95 % higher thermal performance than the Ag-HEG/Water hybrid nanofluid. Furthermore, the MgO–TiO 2 /Water and Ag-HEG/Water hybrid nanofluids have the highest and lowest thermal performance at the highest considered Dean number, respectively. Consequently, the MgO–TiO 2 /Water hybrid nanofluid exhibits approximately 39.22 % higher thermal performance than the Ag-HEG/Water hybrid nanofluid. The MgO–TiO 2 /Water hybrid nanofluid has the highest and lowest thermal performance at the lowest Dean number, with φ 1 = φ 2 = 0.7 and φ 1 = φ 2 = 0.3, respectively. The φ 1 = φ 2 = 0.7 model has a thermal performance that is approximately 39.28 % greater than the φ 1 = φ 2 = 0.3 model at the lowest regarded Dean number. At the highest regarded Dean number, the MgO–TiO 2 /Water hybrid nanofluid with φ 1 = φ 2 = 0.3 exhibits a lower thermal performance than the model φ 1 = φ 2 = 0.7 by about 14.28 %.

Two-phase simulation of nanofluid flow in a heat exchanger with grooved wall

Two-phase simulation of entropy generation and thermo-hydraulic behavior of a therminol/CuO-diamond nanofluid in a heat exchanger

Numerical evaluation of the heat transfer in a shell and corrugated coil tube heat exchanger with three various water‐based nanofluids

Hydrothermal behaviour of hybrid nanofluid flow in a shell-and conical coil tube heat exchanger; numerical approach

Numerical investigation of the simultaneous effect of twisted tape and nanofluid hybrid in shell and spiral tube heat exchanger with a special design

Property of Water-Nanoparticle Flow and Heat Transfer in the Double-Tube Heat Exchanger with Nanofluid

Numerical simulation of nanofluid turbulent flow in a double-pipe heat exchanger equipped with circular fins

Thermal analysis of nanofluids flow in a double pipe heat exchanger with twisted tapes insert in both sides

A novel application for energy efficiency improvement using nanofluid in shell and tube heat exchanger equipped with helical baffles

Effect of using hybrid nanofluid and vortex generator on thermal performance of plate–fin heat exchanger: numerical investigation

Experiment on Heat Exchanger Using Innovative Coils and Phase Change Material/MXene Nanofluids

Thermal performance investigation of N‐shape double‐pipe heat exchanger using Al2O3, TiO2, and Fe3O4‐based nanofluids

Effects of geometrical and operational parameters on heat transfer and fluid flow of three various water based nanofluids in a shell and coil tube heat exchanger

Using different geometries on the amount of heat transfer in a shell and tube heat exchanger using the finite volume method

Numerical Study of a Heat Exchanger with a Rotating Tube Using Nanofluids under Transitional Flow

Finite difference simulation of natural convection of two-phase hybrid nanofluid along a vertical heated wavy surface

Analysis of thermal efficiency of a corrugated double-tube heat exchanger with nanofluids

On the Role of Nanofluids in Thermal-hydraulic Performance of Heat Exchangers-A Review

Use of Organic and Copper-Based Nanoparticles on the Turbulator Installment in a Shell Tube Heat Exchanger: A CFD-Based Simulation Approach by Using Nanofluids

An investigation of the exergy and first and second laws by two-phase numerical simulation of various nanopowders with different diameter on the performance of zigzag-wall micro-heat sink (ZZW-MHS)