Abstract:The present work considers a shell-and-coil heat exchanger, and the hybrid nanofluid's flow and heat transfer inside the proposed thermal system are numerically evaluated. The coil tube has a conical pattern and is oriented horizontally inside the shell. Three water-based hybrid nanofluids are considered here as heat transfer fluids. A commercial CFD code that uses the finite volume method performs the numerical analysis. The regime of fluid flow is turbulent in both coil and shell sections. The validation analysis of the present numerical model was performed using the experimental results of the reference, and accordingly, the accuracy of the present numerical model was proved. This work includes two sectors. In the first part, the volume concentration of the considered hybrid nanofluid was kept constant, and the influence of the hybrid nanofluid kind on the hydrothermal behaviour of the shell-conical-coil heat exchanger was evaluated numerically. In this section, three hybrid nanofluids, (i) Water/MgO–TiO 2 , (ii) Water/MOS 2 -CuO, and (iii) Water/Ag-HEG, were employed. Also, for all suggested hybrid nanofluids, the volume concentration of both employed nanoparticles are equal to each other, φ 1 = φ 2 . The obtained outcomes depicted that between various considered heat transfer fluids, the Water/MgO–TiO 2 model displayed the most outstanding thermal performance value in all the investigated Dean numbers, and the model Water/MOS 2 -CuO was in second place. Moreover, the maximum thermal performance for the hybrid nanofluid was obtained at φ 1 = φ 2 = 0.7. The Ag-HEG/Water and MgO–TiO 2 /Water hybrid nanofluids have the lowest and maximum thermal performance at the lowest considered Dean number among the evaluated hybrid nanofluids. As a result, the MgO–TiO 2 /Water hybrid nanofluid has roughly 18.95 % higher thermal performance than the Ag-HEG/Water hybrid nanofluid. Furthermore, the MgO–TiO 2 /Water and Ag-HEG/Water hybrid nanofluids have the highest and lowest thermal performance at the highest considered Dean number, respectively. Consequently, the MgO–TiO 2 /Water hybrid nanofluid exhibits approximately 39.22 % higher thermal performance than the Ag-HEG/Water hybrid nanofluid. The MgO–TiO 2 /Water hybrid nanofluid has the highest and lowest thermal performance at the lowest Dean number, with φ 1 = φ 2 = 0.7 and φ 1 = φ 2 = 0.3, respectively. The φ 1 = φ 2 = 0.7 model has a thermal performance that is approximately 39.28 % greater than the φ 1 = φ 2 = 0.3 model at the lowest regarded Dean number. At the highest regarded Dean number, the MgO–TiO 2 /Water hybrid nanofluid with φ 1 = φ 2 = 0.3 exhibits a lower thermal performance than the model φ 1 = φ 2 = 0.7 by about 14.28 %.

Effect of using hybrid nanofluid and vortex generator on thermal performance of plate–fin heat exchanger: numerical investigation

Numerical investigation of the simultaneous effect of twisted tape and nanofluid hybrid in shell and spiral tube heat exchanger with a special design

Evaluation of thermal performance factor by hybrid nanofluid and twisted tape inserts in heat exchanger

Numerical investigation of turbulent nanofluid flow behavior in a multi-stream plate-fin heat exchanger with a novel design of fractal fins

Effect of Al2O3/water nanofluid on performance of parallel flow heat exchangers

Thermal performance enhancement of shell and helical coil heat exchanger using MWCNTs/water nanofluid

Heat transfer enhancement of finned shell and tube heat exchanger using Fe2O3/water nanofluid

Numerical study of heat transfer, exergy efficiency, and friction factor with nanofluids in a plate heat exchanger

Performance analysis of a plate heat exchanger using various nanofluids

Improvement of Plate-Fin Heat Exchanger Performance with Assistance of Various Types of Vortex Generator

Study the effect of hot fluid flow rate and carbon nanotube–water on the performance of nanofluid in gasketed plate heat exchanger

Thermal performance augmentation in a pipe employing hybrid nanofluid and a plate as turbulator with V-shaped double-winglet ribs

Effects of geometrical and operational parameters on heat transfer and fluid flow of three various water based nanofluids in a shell and coil tube heat exchanger

A novel application for energy efficiency improvement using nanofluid in shell and tube heat exchanger equipped with helical baffles

Numerical Study And Optimization Of Corrugation Height And Angle Of Attack Of Vortex Generator In The Wavy Fin-And-Tube Heat Exchanger

Numerical study on the thermal performance of the shell and tube heat exchanger using twisted tubes and Al2O3 nanoparticles

Recent Achievements in Heat Transfer Enhancement with Hybrid Nanofluid in Heat Exchangers: A Comprehensive Review

Thermal performance investigation of N‐shape double‐pipe heat exchanger using Al2O3, TiO2, and Fe3O4‐based nanofluids

Experimental Investigation of the Effect of Graphene/Water Nanofluid on the Heat Transfer of a Shell-and-Tube Heat Exchanger

Optimal Configuration of Vortex Generator for Heat Transfer Enhancement in a Plate-Fin Channel

Hydrothermal behaviour of hybrid nanofluid flow in a shell-and conical coil tube heat exchanger; numerical approach