Abstract:Dodecafluoroheptyl methacrylate (DFMA), n-butyl acrylate (BA) and methyl methacrylate (MMA) were copolymerized for preparation of fluorinated latexes through miniemulsion copolymerization without any costabilizer. In this reaction system, extremely hydrophobic DFMA was used as a chemical reagent which made the monomer droplets unimodal distribution. But after a while, the monomer droplets coalescenced together and made the monomer droplet size changing from about 130 nm to 400 nm. The oligomers of poly(dodecafluoroheptyl methacrylate) containing a lot of -CF2- and -CF3 segments with low surface energy, were generated quickly and it was proved from H-1-NMR spectrum which showed DFMA has a high composition in the earlier copolymer. The oligomers not only with extremely hydrophobic but also oleophobic natural capacity would take the same effect of conventional costabilizer on the miniemulsion polymerization to increase the surface of monomer droplets and decrease the monomer droplets size. The monomer droplet or particle size distribution of the semifinished and the final products was determined using LS-230 Coulter particle size analyzer. As the process of polymerization was going on, the smaller monomer droplets or particles would detach from the larger ones. Simultaneously, the particles did not maintain unimodal distribution after the beginning of polymerization. However, as the process of polymerization was going on, the particle size distribution would return to the unimodal distribution again. Between the processes of polymerization, the particle sizes changed from about 400 nm to 80 nm. On the base of fundamental theory of miniemulsion polymerization, the particle sizes of the latexes with the convensional costabilizer would not change too much. So, the reason is the oligomers, first generated at the process of polymerization, contain a lot of -CF2- and -CF3 segments with low surface energy to make the smaller particles existence stably. There is no differences about the particle size distributions between the final products initiated by potassium persulfate (KPS, water-soluble initiator) and 2,2'-azobisisobutyronitrile (AIBN, oil-soluble initiator) There were too much differences between the two kinds of initiator, the final products of this polymerization would exhibit bimodal distributions, if some crosslinking agents were added into the systems to reduce the activities of oligomer chains. One of the peaks was at about 80 nm, equaling to that one without any crosslinking agent, the other one was at about 400 nm, equaling to that one before polymerization. With the same contents of crosslinking agents, the effect on particle size distribution of the final products was much more initiated by AIBN. Because the polymerization was taken place in the center of the particles initiated by AIBN to generate the oligomers, the crosslinking agents would reduce the movement activity of the oligomer and make the oligomers shift to the surfaces of the particle more difficult. However, the effect on particle size distribution of the final products was less initiated by KPS. Because the polymerization initiated by KPS was taken place at the inside surface of the particle, as well as the generated oligomers, the movement of the oligomer was not necessary. On the base of the experimental results, the mechanism of miniemulsion polymerization with in situ formed costabilizer was presented.

Miniemulsion polymerization using carboxylated graphene quantum dots as surfactants: effects of monomer and initiator type

The Synthesis of Amphiphilic Luminescent Graphene Quantum Dot and Its Application in Miniemulsion Polymerization

Surfactant-Ligand Design For Ab Initio Emulsion Atom Transfer Radical Polymerization

Solution and Aqueous Miniemulsion Polymerization of Vinyl Chloride Mediated by a Fluorinated Xanthate

Ab Initio Emulsion and Miniemulsion Polymerization of Styrene Mediated by a Cyclohexenyl-Functionalized Amphiphilic RAFT Agent

Aqueous synthesis of amphiphilic graphene quantum dots and their application as surfactants for preparing of fluorescent polymer microspheres

The Influence of Monomer Types on the Colloidal Stability in the Miniemulsion Copolymerization Involving Alkoxysilane Monomer

The Influence of Surfactant Coverage of the Minidroplets on Raft Miniemulsion Polymerization

Mini-Emulsification and Mini-Emulsion Polymerization of Methyl Methacrylate/Nanosilica Dipsersion

Viscoelastic Study of Single Chain Cyclized Polymeric Nanoparticles and Linear Polymers Blends

Synthesis and performance of oleic acid-sodium dodecyl sulfate modified graphene/styrene-acrylic emulsion nanocomposites

Preparation of Miniemulsion and Nanocapsules by Reversible Addition-Fragmentation Chain Transfer and Chemical Shearing Method

KINETICS OF CATIONIC MINIEMULSION RING-OPENING POLYMERIZATION FOR OCTAMETHYLCYCLOTERTRASILOXANE

Model System for Surfactant-Free Emulsion Copolymerization of Hydrophobic and Hydrophilic Monomers in Aqueous Solution

Microemulsion Polymerization of Siloxane with Nonionic Surfactants As Emulsifiers

Quartz Crystal Microbalance Study of the Kinetics of Surface Initiated Polymerization

Emulsion Based Nanoarchitectonics for Styrene–Butyl Acrylate Copolymerization upon Pickering Mechanism

Influences of Initiators on Conversions of Vinyl Chloride Micro-Suspension Polymerizations and Particle Size Distributions of Poly(vinyl chloride) Resins

Miniemulsion Polymerization with in Situ Formed Costabilizer

In situ polymerization of a novel surfactant on a graphene surface for the stable dispersion of graphene in water

Dendrimer-Based Demulsifiers for Polymer Flooding Oil-In-Water Emulsions