Abstract:A study has been made of the influence of austenitizing temperature on the ambient temperature toughness of commercial AISI 4340 ultrahigh strength steel in the as-quenched (untempered) and quenched and tempered at 200°C conditions. As suggested in previous work, a systematic trend ofincreasing plane strain fracture toughness(K)Ic anddecreasing Charpy V-notch energy is observed as the austenitizing temperature is raised while the yield strength remains unaffected. This effect is seen under both static <slowbend> and dynamic (impact) loading conditions, and is rationalized in terms of a differing response of the microstructure, produced by each austenitizing treatment, to the influence of notch root radius on toughness. Since failure in all microstructures was observed to proceed primarily by a ductile rupture (microvoid coalescence) mechanism, an analysis is presented to explain these results, similar to that reported previously for stress-controlled fracture, based on the assumption that ductile rupture can be considered to be strain-controlled. Under such conditions, the decrease in V-notch Charpy energy is associated with a reduction in critical fracture strain at increasing austenitizing temperatures, consistent with an observed decrease in uniaxial and plane strain ductility. The increase in sharp-crack fracture toughness, on the other hand, is associated with an increase in “characteristic distance” for ductile fracture, resulting from dissolution of void-initiating particles at high austenitizing temperatures. The microstructural factors which affect this behavior are discussed, and in particular the specific role of retained austenite is examined. No evidence was found that the enhancement of fracture toughness at high austenitizing temperatures was due to the presence of films of retained austenite. The significance of this work on commonly-used Charpy/KIc empirical correlations is briefly discussed.

Improvement of AISI 4340 steel properties by intermediate quenching – microstructure, mechanical properties, and fractography

On the Strain Hardening and Tensile Properties of AISI 4140 Steel via Single‐Step Quenching and Partitioning Treatments

The effect of austenitizing temperature on the microstructure and mechanical properties of as-quenched 4340 steel

Further considerations on the inconsistency in toughness evaluation of AISI 4340 steel austenitized at increasing temperatures

Effect of cryogenic treatment on the mechanical properties of 4340 steel

Effect of Heat Treatment on Microstructure and Properties of Improved 40crni2si2mov Steel

Toughening of AISI 410 Stainless Steel Through Quenching and Partitioning and Effect of Prolonged Aging on Microstructure and Mechanical Properties

Tailoring the Microstructure using Quenching and Partitioning Processing in a Commercial Mn-Si-Cr Spring Steel to Improve Tensile Properties

Improving the Cryogenic Strength–Ductility–Toughness of Multi‐Alloy Steel by Optimizing the Feature of Retained Austenite

Influence of Intercritical Temperature on the Microstructure and Mechanical Properties of 6.5 Pct Ni Steel Processed by Ultra-fast Cooling, Intercritical Quenching and Tempering

Increase in Low-Carbon Steel 12GBA Strength and Cold Resistance by a Deformation-Thermal Effect

Study of Quenching and Partitioning (Q&P) and Ultrasonic Surface Rolling (USR) Process on Microstructure and Mechanical Property of a High-Strength Martensitic Steel

Effect of Rapid Heating and Quenching on Microstructure and Mechanical Properties of High Strength Low Alloy Steel

Influence of austenitizing temperature on microstructure and mechanical properties of AISI 431 martensitic stainless steel electron beam welds

Effect of Intercritical Austenitizing Temperature during Quenching–Intercritical Quenching–Tempering Process on Toughness of 25Mn2Si2Cr Bainitic Steel

Synergistic optimization of microstructure and mechanical properties of AISI 430 ferritic stainless steel via dual-phase zone annealing process

Improvement of Strength and Oxidation Resistance at High Temperature in AISI 4140 Steel by Micro-Alloying Chromium and Tungsten for Automotive Engine Applications

Improving the Wear Properties of AISI4130 Steel Using Laser Surface Hardening Treatment

Fracture toughness improvement of austempered high silicon steel by titanium, vanadium and rare earth elements modification

Microstructure and Mechanical Properties of Low- and Medium-Carbon Si-Rich Low-Alloy Steels Processed by Austemping after Intercritical Annealing

The effect of deep cryogenic treatments on the mechanical properties of an AISI H13 steel