Abstract:Ceramic Li6.55Al0.2La3Zr2O12 (LLZO) is one of the most attractive electrolyte materials for solid-state batteries that combined with metallic Li anodes holds the promise for safer and more energetically dense battery, but its performance is limited by the increases in electrolyte-electrode interfacial resistances upon cycling. The combination of Li + -conducting ceramics and polymers offers a new pathway to create better electrolytes with both high ionic conductivity and good (electro)mechanical interfacial properties. We optimized two-step annealing processing conditions for the fabrication of low temperature cubic-LLZO nanofibers and Li 2 CO 3 removal from the surface of the nanofibers. Using industrially relevant roll-to-roll electrospinning and slot-die coating, we fabricated thin composite membranes with reproducible thickness down to 50 microns. We investigated PEO based composite polymer electrolyte (CPE) with a high, 50 wt% loading of Al-doped LLZO nanofibers in comparison with nanofiber-free PEO electrolyte. XPS measurements show that LLZO is not present at the composite electrolyte surface, and solid electrolyte interphase (SEI) formation is dictated solely by PEO and LiTFSI when reacting with Li metal. Electrochemical SEI formation, studied by cyclic voltammetry, shows SEI formation is identical with and without up to 75 wt% LLZO in the electrolyte. Galvanostatic cycling with lithium symmetric cells shows that the critical current density (CCD) can be tripled by including 50 wt% LLZO, but half cell cycling reveals this comes at the cost of CE. Varying the LLZO loading shows that even a small amount of LLZO drastically lowers the CE, from 88% at 0 wt% LLZO to 77% at just 2 wt% LLZO. Mesoscale modelling reveals that the increase in CCD cannot be explained by an increase in the macroscopic or microscopic stiffness of the electrolyte; only the microstructure of the LLZO nanofibers in the PEO-LiTFSI matrix slows dendrite growth by presenting physical barriers that the dendrites must push or grow around. This tortuous lithium growth mechanism around the LLZO is corroborated with mass spectrometry imaging. Electrochemical impedance spectroscopy (EIS) analysis showed comparable bulk ionic and interfacial resistances with and without nanofibers, indicating that PEO dominates Li + transport and interfacial chemistry. The total Li-ion conductivity of the composite is still governed by the polymer matrix due to high interfacial resistance between the garnet particles and the PEO/LiTFSI matrix. This work highlights important elements to consider in the design of CPEs for high-efficiency lithium metal batteries.

Influence of the Processing on the Ionic Conductivity of Solid-State Hybrid Electrolytes Based on Glass-Ceramic Particles Dispersed in PEO with LiTFSI

Influence of the Polymer Structure and its Crystallization on the Interface Resistance in Polymer-LATP and Polymer-LLZO Hybrid Electrolytes

Ion-conductive vs. non-ion-conductive ceramic fillers in silane-linked polyethylene oxide-based composite polymer electrolytes with high room-temperature ionic conductivity

Influence of Molecular Weight and Lithium Bis(trifluoromethanesulfonyl)imide on the Thermal Processability of Poly(ethylene oxide) for Solid-State Electrolytes

Cold Sintering of Li6.4La3Zr1.4Ta0.6O12/PEO Composite Solid Electrolytes

On the interfacial lithium dynamics in Li7La3Zr2O12:poly(ethylene oxide) (LiTFSI) composite polymer-ceramic solid electrolytes under strong polymer phase confinement

Synergistic Effect of Processing and Composition X on Conductivity of Xli2s-(100 − X)p2s5 Electrolytes

Investigation of Polymer/Ceramic Composite Solid Electrolyte System: The Case of PEO/LGPS Composite Electrolytes

(Invited) Advancing Understanding of Composite Polymer Electrolytes with LLZO Nanofibers

Promoted Li+ Conduction in PEO-based All-Solid-state Electrolyte by Hydroxyl-Modified Glass Fiber Fillers

Revealing the Role of Active Fillers in Li‐ion Conduction of Composite Solid Electrolytes

Preparation and electrochemical behaviors of composite solid polymer electrolytes based on polyethylene oxide with active inorganic-organic hybrid polyphosphazene nanotubes as fillers

Properties of the Interphase Formed between Argyrodite-Type Li6PS5Cl and Polymer-Based PEO10:LiTFSI

Synergy of Inorganic Fillers in Composite Thermoplastic Polymer/Ionic Liquid/LiTFSI Electrolytes

Role of Filler Content and Morphology in LLZO/PEO Membranes

Tuning Ceramic Surface to Minimize the Ionic Resistance at the Interface between PEO- and LATP-Based Ceramic Electrolyte

Novel PEO-based solid composite polymer electrolytes with inorganic–organic hybrid polyphosphazene microspheres as fillers

Li+ Conduction in a Polymer/Li1.5Al0.5Ge1.5(PO4)3 Solid Electrolyte and Li-Metal/Electrolyte Interface

Ionic Conductivity and Cycling Performance in PEO Polymer Electrolyte Enhanced by Non-Milled In Situ Nano-LLZO Powders

In situ polymerization of 1,3-dioxolane infiltrating 3D garnet framework with high ionic conductivity and excellent interfacial stability for integrated solid-state Li metal battery

Manipulating ionic conductivity through chemical modifications in solid-state electrolytes prepared with binderless laser powder bed fusion processing