The use of supercritical water for the catalyst-free oxidation of coarse aluminum for hydrogen production

Keena A. Trowell,Sam Goroshin,David L. Frost,Jeffrey M. Bergthorson

DOI: https://doi.org/10.1039/d0se00996b

2020-01-01

Abstract:Supercritical water is used to oxidize aluminum scrap and 3 mm aluminum slugs without employing catalysts, milling or specialized alloys.

materials science, multidisciplinary,chemistry, physical,energy & fuels

What problem does this paper attempt to address?

Oxidation of coarse aluminum in pressured water steam for energy applications

Mikhail S. Vlaskin,George E. Valyano,Andrey Z. Zhuk,Evgeny I. Shkolnikov

DOI: https://doi.org/10.1002/er.5561

IF: 4.6

2020-06-03

International Journal of Energy Research

Abstract:<p>In this paper, we show how to conduct fast and complete oxidation of aluminum of any size in water without any additional chemicals and no extreme temperatures. Using a simple and easily repeatable experimental procedure, we studied the oxidation of coarse aluminum granules in distilled water at temperatures of 250°C to 400°C. We present the results of the oxidation experiments as well as structural analysis of the solid products by X‐Ray Diffraction and Scanning Electron Microscopy. For the first time, we have shown that aluminum is oxidized more effectively in gaseous steam than in liquid water (at same temperature). The rate of aluminum oxidation in steam increases with increasing temperature and steam pressure. Conversion degree of aluminum granules with the size of about 1 cm was 0.93 at 300°C after 4 hours; 0.96 and 1 at 350°C after 2 and 4 hours, respectively; 0.81 and 0.99 at 400°C after 1 and 2 hours, respectively. We showed that in liquid water, aluminum oxidation penetrates just a few microns into the aluminum and the reaction stops. Unlike liquid water, steam can easily penetrate through the porous layer of the solid oxidation product. We also discuss energy generation strategies for aluminum‐water reactor and propose principal schemes of aluminum‐fueled power plants.</p>

energy & fuels,nuclear science & technology
Hydrogen production rates of aluminum reacting with varying densities of supercritical water

Keena Trowell,Sam Goroshin,David Frost,Jeffrey Bergthorson

DOI: https://doi.org/10.1039/d2ra01231f

IF: 4.036

2022-01-01

RSC Advances

Abstract:Hydrogen production rates of aluminum reacting with various densities of supercritical water are determined using a novel method. High-density supercritical water is found to be the most efficient oxidizer, in terms of both reaction rates and yields.

chemistry, multidisciplinary
Experimental Study on Catalyst-Free High-Temperature and High-Pressure Aluminum-Water Reaction Characteristics Using Metal As Energy Carrier

Xinyue Gao,Chang'an Wang,Yujie Hou,Lin Zhao,Wengang Bai,Defu Che

DOI: https://doi.org/10.1016/j.ijhydene.2023.09.216

IF: 7.2

2024-01-01

International Journal of Hydrogen Energy

Abstract:Aluminum-water reaction have the potential for clean hydrogen production and power generation. In this work, the effects of reactions such as temperature, pressure, water-aluminum ratio, and water state of the high-temperature and high-pressure aluminum-water reaction are experimentally investigated. The findings demonstrate that the micron aluminum powder can produce 100% hydrogen in a catalyst-free neutral environment by enhancing the temperature and pressure. The aluminum-water interaction is favored by excess water and the gas-liquid two-phase state. The effects of Na+ and K+ ions within water in high-temperature and high-pressure reactions under neutral environments have a negligible effect, and the in-situ reaction with clean water has a high hydrogen yield. The high-temperature and high-pressure aluminum-water reactions consist of four stages. Hydrogen and heat are generated only when water molecules and activated aluminum are constant touch. He results provide the foundation for aluminum-water-based hydrogen cogeneration.
Molten Salt-Enhanced Production of Hydrogen by Using Skimmed Hot Dross from Aluminum Remelting at High Temperature

Peng Li,Jun Wang,Xiuxia Zhang,Xinmei Hou,Bingji Yan,Hongwei Guo,Seshadri Seetharaman

DOI: https://doi.org/10.1016/j.ijhydene.2017.04.046

IF: 7.2

2017-01-01

International Journal of Hydrogen Energy

Abstract:The skimmed hot dross generated in secondary production of aluminum contains high amount of metallic aluminum and also the potential heat. An innovative process for hydrogen generation using skimmed hot dross from aluminum remelting industry is proposed in this work. The reaction behavior between skimmed dross and water steam in terms of hydrogen evolution variation at high temperature is studied. The results show that the inherent salts in the dross could accelerate the hydrogen generation at temperature region of 600850 degrees C by dissolving the amorphous and gamma-Al2O3 product layer in water steam atmosphere. The maximum aluminum conversion degree was found to be more than 60%, and the hydrogen evolution rate was over 60 cm(3) g-(1)min-(1) when skimmed dross with 30 wt% Al was used in non-isothermal test. The mechanism related to the texture responding of alumina layer with different amount of salts additives and temperatures is discussed. (C) 2017 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.
Experimental study on characteristics and mechanism of hydrogen production from aluminium–water reaction for carbon-free power generation

Xinyue Gao,Chang'an Wang,Yujie Hou,Lin Zhao,Wengang Bai,Defu Che

DOI: https://doi.org/10.1016/j.fuel.2024.133206

IF: 7.4

2024-09-26

Fuel

Abstract:The potential of hydrogen production and power generation via aluminum–water reactions has been limited by the inhibition phenomenon within the oxide layer. While raising the temperature effectively mitigates this issue, sustaining liquid water state requires high pressure, an underexplored factor. Furthermore, the underlying mechanisms behind these processes remain unclear. This study investigates disparities in hydrogen production characteristics and mechanisms between aluminum–gas water reactions and aluminum–liquid water reactions within the temperature range of 250–376 °C and pressures ranging from 4.0–23.5 MPa. The effects of reaction temperature, pressure, supercritical water, duration, and heating rate on hydrogen yield, solid products, and reaction mechanisms for millimeter-sized aluminum particles were investigated and a new carbon-free power generation system was proposed. The 1–4 mm aluminum particles achieve 100 % hydrogen yield at 350–360 °C and 16.5–18.7 MPa. The supercritical water demonstrates strong reactivity, inhibiting passivation, with 8 mm aluminum particles fully oxidized at 376 °C and 23.5 MPa. Hydrogen yield from gaseous water reactions is slightly lower or equal to that from liquid water reactions due to the differences in mechanisms and aluminum surface contact opportunities. The proposed zero-carbon power generation system demonstrates the potential of aluminum for continuous energy storage and large-scale power generation, contributing to a clean and safe energy storage system.

energy & fuels,engineering, chemical
Metal-Free Catalyst with Large Carbon Defects for Efficient Direct Overall Water Splitting in Air at Room Pressure

Qingyao Wu,Mengmeng Zhu,Jingjing Cao,Xiao Wang,Yang Liu,Chensheng Xiang,Mingwang Shao,He Tian,Zhenhui Kang

DOI: https://doi.org/10.1021/acsami.0c02544

IF: 9.5

2020-01-01

ACS Applied Materials & Interfaces

Abstract:Hydrogen can be used as a conventional clean energy resource, only by obtaining it in a cheap, simple, and feasible way. From the perspective of solar energy utilization, photocatalytic water splitting is essentially limited by high electric energy and intermittent solar energy. Here, we demonstrate that the carbon defects could decompose water directly by using low-value mechanical energy in the daily environment without using the sacrificial agent. The prepared metal-free carbon catalyst (OPC-900) with rich graphene topological defects shows several redox states in acetonitrile, which can accumulate redox equivalents and respond for overall water splitting in air at room pressure. Under stirring or light conditions, charges can be created and accumulated on the catalyst surface and split water into H2 and O2 in low conductivity medium. The mechanical energy conversion efficiency of stirring in ultrapure water is 7.01%. Our work combines visible light with low-value mechanical energy for widespread decomposition of water to produce hydrogen in air under normal pressure.
Borohydride Hydrolysis Using a Mechanically and Chemically Stable Aluminium‐Stainless Steel Porous Monolith Catalyst Made by 3D Printing

Frances Pope,Xhoi Xhaferri,Daan Giesen,Norbert J. Geels,Jessica Pichler,Gadi Rothenberg

DOI: https://doi.org/10.1002/cssc.202401264

IF: 8.4

2024-10-30

ChemSusChem

Abstract:Hydrogen for a Raney day: Adding aluminium to stainless steel powder and subsequently leaching it out from 3D printed catalyst‐reactor monoliths gives highly active and stable porous metal catalysts for hydrogen generation from borohydrides. The catalysts perform well in both batch and continuous setups under realistic conditions, retaining their activity for at least 100 h on stream. The challenge of moving to a carbon‐free energy economy is highlighted in the context of technology and materials restrictions. Many technologies needed for the so‐called energy transition depend on critical metals such as platinum, lithium, iridium and cobalt. Here we focus on solid borohydride salts as hydrogen carriers, studying catalysts for hydrogen release. We combine metal 3D printing technology and a Raney‐type leaching process to make structured macroscopic catalyst/reactor monoliths of cobalt, aluminium and stainless steel with well‐defined micropores. Remarkably, the blank catalyst samples, which are made only from aluminium and stainless steel (Al‐SS), show high activity and, importantly, high stability in borohydride hydrolysis, with no mass loss and no surface poisoning. The batch results are confirmed in a continuous setup running for 96 h. Catalyst performance is attributed to the stable porous structure, the mechanical stability of the stainless steel macrostructure, and the presence of accessible Al(OH)x sites. This research shows a clear contribution to sustainability based on multi‐factor comparison: The Al‐SS catalyst outperforms the state‐of‐the‐art on mechanical and chemical durability, it is both PGM‐free and CRM‐free, and its preparation follows a simple, scalable and low‐waste procedure.

chemistry, multidisciplinary,green & sustainable science & technology
Experimental Investigation of the Catalyst-Free Reaction Characteristics of Micron Aluminum Powder with Water at Low and Medium Temperatures

Xinyue Gao,Chang'an Wang,Wengang Bai,Yujie Hou,Defu Che

DOI: https://doi.org/10.1016/j.est.2022.106543

IF: 9.4

2023-01-01

Journal of Energy Storage

Abstract:Aluminum metal has a high energy density and can react with water to produce hydrogen instantly, which is environmental-friendly and safe. Aluminum has great potential to provide a good carrier for energy and hydrogen storage. The utilization of aluminum is constrained by the oxide layer on its surface. In order to promote the aluminum-water reaction to continue efficiently, the reaction needs to be activated. The modification of aluminum is often complicated and dangerous, and it is difficult to apply the hydrogen produced by the reaction and the heat released. The increase of temperature and pressure of the reaction has also been proved as a useful activation method. Continuous reactions are difficult to achieve at high temperature and pressure, and it becomes difficult to obtain reaction initiation and development processes. However, the reaction process has an essential impact on the utilization of the aluminum-water reaction. In this paper, the aluminum-water reaction process at medium temperature was investigated using micron aluminum powder. The effects of initial temperature, particle size of aluminum powder and water type on the reaction were further analyzed. In addition, the kinetic analysis of the aluminum-water reaction was carried out to obtain kinetic models. Experimental results indicate that the product of the aluminum-water reaction is Al(OH)(3) at 90-150 degrees C. The reaction initial temperature shows a multipolar effect on the reaction between aluminum and water. The hydrogen yield from the reaction between similar to 25 mu m aluminum powder and tap water at 150 degrees C is 31.9 %. The pre-exponential factor and apparent activation energy increase with the reaction proceeding. The present research is conducive to further safe and efficient utilization of micron aluminum powder for energy conversion, and benefits the achievement of carbon peaking and carbon neutrality.
Cogeneration of hydrogen, alumina, and heat from aluminum-water reactions

Thomas Kirton,Florin Saceleanu,Mahsa Salehi Mobarakeh,M. Reza Kholghy

DOI: https://doi.org/10.1016/j.ijhydene.2024.04.038

IF: 7.2

2024-04-27

International Journal of Hydrogen Energy

Abstract:Oxidation of metals in water has been explored to generate sustainable carbon free hydrogen and power. This paper studies the thermal ignition of micro aluminum powders in high-pressure deionized (DI) water for cogeneration of hydrogen, heat, and alumina. Thermal ignition (temperature runaway) is necessary to ensure achieving high reaction temperatures, past the saturation temperature, where alumina formation is thermodynamically favorable. Aluminum powders with nominal particle diameters of 1, 10 and 45 μm with spherical morphology and 2 μm with flake morphology were mixed with DI water to form slurries with equivalence ratio of 1.3 in a 100 mL batch reactor. The reactor was pressure maintained between 500 and 2000 psig using a back-pressure regulator, and heat was injected into the slurry through an electric band heater. It was found that 1 and 2 μm powders ignite in compressed water, but only the 2 μm slurries achieved temperatures above saturation temperature at pressures above 700 psig. On the other hand, 10 and 45 μm powders require saturated steam for ignition at pressures above 1000 and 1200 psig, respectively. Hydrogen volume data indicate that larger powders at higher pressures optimize reaction yield, which is likely due to delayed ignition which preserves the active aluminum content and the particle-water reaction interfaces. Scanning electron microscopy images illustrate that the byproduct particles crack upon ignition at the saturation temperature, which increases the specific surface area by an order of magnitude relative to the aluminum powders. Pore size distribution data indicates the formation of micro, meso and macropores upon the ignition. X-ray powder diffraction data indicate that reaction temperatures above 450 °C promote the formation of alumina (Al 2 O 3 ) instead of boehmite (ALOOH).

energy & fuels,electrochemistry,chemistry, physical
A Critical Assessment of Aluminium-Water Reaction for On-Site Hydrogen-Powered Applications

Prabhsharan Kaur,Gaurav Verma

DOI: https://doi.org/10.1016/j.mtener.2024.101508

IF: 9.257

2024-01-24

Materials Today Energy

Abstract:Over the last three decades, there has been a tremendous amount of research interest around the world in developing sophisticated technologies that may enable the domestic hydrogen economy. If the cost of producing hydrogen falls far below that of fossil fuels, it will be able to run the transportation, construction, and energy sectors. The vision of a decarbonized future in which hydrogen is used as a common fuel will be realized soon through infrastructural developments. Aluminium (Al) and water react to produce hydrogen on-site, which is a simple and affordable process. Two benefits come from this: first, it eliminates the need for additional logistics for the storage and shipping of hydrogen; second, water is easily accessible in the field and Al is safer to use. Although this technique appears intriguing, a major barrier to its wide-spread applications is the development of a passive oxide layer on the Al surface. The advantages and disadvantages of various Al activation techniques are covered in this review article. In addition to analyzing the effectiveness and technical issues of the Al-water reaction techniques used to power on-site hydrogen-powered fuel cell vehicles, it gives a critical examination of key parameters that derive the Al-water reaction mechanism.

materials science, multidisciplinary,chemistry, physical,energy & fuels
A microreactor with superhydrophobic Pt–Al2O3 catalyst coating concerning oxidation of hydrogen off-gas from fuel cell

Wei Yu,Jiabo Tao,Xinhai Yu,Shuangliang Zhao,Shan-Tung Tu,Honglai Liu

DOI: https://doi.org/10.1016/j.apenergy.2016.01.048

IF: 11.2

2017-01-01

Applied Energy

Abstract:•Pt–Al2O3 was modified to superhydrophobicity via grafting by FAS.•Hydrophobic modification greatly promoted catalytic activity and stability.•Catalytic activity heavily depended on hydrophobicity extent in humid condition.
An aluminum/cobalt/iron/nickel alloy as a precatalyst for water oxidation

Mohammad Mahdi Najafpour,Somayeh Mehrabani,Robabeh Bagheri,Zhenlun Song,Jian-Ren Shen,Suleyman I. Allakhverdiev

DOI: https://doi.org/10.1016/j.ijhydene.2017.12.025

IF: 7.2

2018-01-01

International Journal of Hydrogen Energy

Abstract:Among different strategies, water splitting toward hydrogen production is a promising process to store energy from intermittent sources. However, the anodic water oxidation is a bottleneck for water splitting. In this paper, we report an aluminum/cobalt/iron/nickel alloy as a precatalyst for the electrochemical water oxidation. The alloy electrode contains different metal ions including cobalt, iron, and nickel which all are efficient for water oxidation is tested. We characterized this electrode using scanning electron microscopy, transmission electron microscopy, diffuse reflectance infrared Fourier transform spectroscopy, Fourier transform infrared spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy and electrochemical methods. After stabilization, the electrode shows an onset overpotential of 200.0 mV and affords a current density of 3.5 mA cm−2 at an overpotential of 600.0 mV in KOH solution at pH 13.

energy & fuels,electrochemistry,chemistry, physical
Supercritical Water Synthesis of Bimetallic Catalyst and Its Application in Hydrogen Production by Furfural Gasification in Supercritical Water

Hui Jin,Xiao Zhao,Xiaohui Su,Chao Zhu,Chongqing Cao,Liejin Guo

DOI: https://doi.org/10.1016/j.ijhydene.2016.10.096

IF: 7.2

2017-01-01

International Journal of Hydrogen Energy

Abstract:Supercritical water not only provides good solvent of biomass gasification but also causes catalyst agglomeration. Therefore, the supercritical water synthesis method was utilized to guarantee the stability of the catalyst. In order to take into account the advantages of different metal catalysts, bimetallic catalysts were prepared based on Ni, Co, Zn and Cu, with TiO2 as carrier. Hydrogen production by furfural gasification in supercritical water was conducted with different catalysts. The experimental results turned out that all combinations showed remarkable stability except for the combination Co + Ni. Zn + Ni and Cu + Zn showed better selectivity on hydrogen, and Co + Ni showed better carbon gasification efficiency. Spherical coke particles were obtained after the reaction with bimetallic catalysts, while the coke particles were amorphous after the reaction with K2CO3. (C) 2016 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.
Catalytic Hydrogen Production from Municipal Sludge in Supercritical Water with Partial Oxidation

Zhang Qinming,Wang Shuzhong,Wang Liang,Xu Donghai

DOI: https://doi.org/10.1007/978-3-540-76694-0_234

2007-01-01

Abstract:This paper describes partial oxidative gasification of municipal sludge with NaOH catalyst, using a batch type reactor. Hydrogen peroxide was employed as oxygen source. The reaction is studied in the ranges of 623–723 K, 23–28 MPa and various reaction time 5–40 min. We found that sludge at low concentrations can be completely gasified and no char or tar was observed. Gaseous products were composed of H2, CO2, CO, CH4, and so on. The improvement of gasification efficiency by partial oxidation was accompanied with high yield of hydrogen and carbon monoxide. The effect of partial oxidation was investigated. For comparison, we also conducted the experiments without catalyst at the same conditions. The yield of hydrogen with NaOH was almost twice as much as that without catalyst. Thus, a base catalyst has a positive effect on partial oxidation of sludge to produce H2. The catalytic effect of NaOH was the inhibition of char formation and promotion of CO yields and thus H2 by water-gas shift reaction.
Thermodynamics of oxidation of an alumina-supported cobalt catalyst by water in F-T synthesis

chaopeng hou,guofu xia,xia sun,yu wu,chao jin,zhennan yan,mingfeng li,zhihai hu,hong nie,dadong li

DOI: https://doi.org/10.1016/j.cattod.2015.08.042

IF: 5.3

2016-01-01

Catalysis Today

Abstract:•Direct oxidation of cobalt by water cannot arise initiatively to CoO, Co3O4, and Co(OH)2.•The reaction in which CoO reacts with H2O to Co(OH)2 could go to the positive direction.•Oxidation of cobalt by water may occur spontaneously with the participation of alumina.•The reactions in the presence of Diaspore and Boehmite could go to right to a great extent probably.
Oxidation Processes and Involved Chemical Reactions of Corrosion-Resistant Alloys in Supercritical Water

Shuwei Guo,Donghai Xu,Ning Wei,Yuzhen Wang,Gang Chen,Shuzhong Wang

DOI: https://doi.org/10.1021/acs.iecr.0c01394

2020-01-01

Industrial & Engineering Chemistry Research

Abstract:Corrosion continues to be a major challenge in developing supercritical water-cooled reactor and supercritical water oxidation systems. Corrosion behaviors of candidate alloy materials used in these environments are significantly affected by the properties of oxides formed on alloy surfaces. This work presents a comprehensive review of the oxidation processes and involved chemical reactions of corrosion-resistant alloys in supercritical water. The oxidation process of an alloy in supercritical water is proposed to have two stages, and chemical reactions at these two stages are described in detail. The transitions of Cr/Ni/Fe oxides and the formation mechanism of oxide film are analyzed comprehensively. Moreover, the diffusion property, protection effect, and stability of oxides in supercritical water are summarized systematically.
Upcycling of Cr-Containing Sulfate Waste into Efficient FeCrO3/Fe2O3 Catalysts for CO2 Hydrogenation Reaction

Yongqi Liu,Shasha Chu,Yuebing Xu,Xinyu Chen,Hao Zhou,Jinlin Li,Yanjie Ren,Xintai Su

DOI: https://doi.org/10.3390/ma17071598

2024-03-31

Abstract:Upcycling Cr-containing sulfate waste into catalysts for CO2 hydrogenation reaction benefits both pollution mitigation and economic sustainability. In this study, FeCrO3/Fe2O3 catalysts were successfully prepared by a simple hydrothermal method using Cr-containing sodium sulfate (Cr-SS) as a Cr source for efficient conversion and stable treatment of Cr. The removal rate of Cr in Cr-SS can reach 99.9% at the optimized hydrothermal conditions. When the synthesized catalysts were activated and used for the CO2 hydrogenation reaction, a 50% increase in CO2 conversion was achieved compared with the catalyst prepared by impregnation with a comparable amount of Cr. According to the extraction and risk assessment code (RAC) of the Reference Office of the European Community Bureau (BCR), the synthesized FeCrO3/Fe2O3 is risk-free. This work not only realizes the detoxification of the Cr-SS but transfers Cr into stable FeCrO3 for application in a catalytic field, which provides a strategy for the harmless disposal and resource utilization of Cr-containing hazardous waste.
A comparison study on aluminum-water reaction with different catalysts

Wenqi Tang,Lihong Yan,Kaiqi Li,Yongfei Juan,Chaopeng Fu,Jiao Zhang

DOI: https://doi.org/10.1016/j.mtcomm.2022.103517

IF: 3.8

2022-06-01

Materials Today Communications

Abstract:The aluminum-water reactions with various organic and inorganic catalysts have been investigated. The effect of catalyst on the rate and yield of hydrogen production and morphology and structure of Al(OH)3 product has been studied. The difference in reaction rate and hydrogen conversion efficacy is mainly ascribed to the ability to destroy alumina film and alkalinity of the catalyst solutions, and the hydrogen conversion efficiency of Al with tetramethylguanidine is the highest. The morphology and structure of the Al(OH)3 product are also characterized. The main phases of Al(OH)3 product prepared by these catalysts are Bayerite and Gibbsite. The morphologies and size distributions of Al(OH)3 products are different. The largest (D50, 64.0 µm) and smallest (D50, 20.8 µm) particle sizes of Al(OH)3 are prepared by the Al-H2O reactions with KOH and tetramethylguanidine, respectively. The role of catalyst in the Al-H2O reaction is discussed in detail.

materials science, multidisciplinary
Anodic aluminum oxide supported Cu-Zn catalyst for oxidative steam reforming of methanol

Jung Hyeon Kim,Young Shin Jang,Jae Chang Kim,Dong Hyun Kim

DOI: https://doi.org/10.1007/s11814-018-0211-9

IF: 2.7

2019-01-26

Korean Journal of Chemical Engineering

Abstract:Oxidative steam reforming of methanol (OSRM) is autothermal and therefore well suited for hydrogen production. The exothermic part of OSRM generates heat at the reactor inlet to be used as the reaction heat for the endothermic methanol steam reforming in the rest of the reactor. With conventional particle catalysts, a hot spot is formed at the reactor inlet because of the poor thermal conductivity in the catalyst bed. The catalyst at the hot spot is deactivated by thermal sintering. Side reactions such as the reverse water gas shift reaction and methanol decomposition reaction become active at the hot spot. We developed a high-thermal-conductivity Al plate catalyst to suppress the formation of the hot spot in the catalyst bed during OSRM. In particular, a strongly bonded layer of anodic aluminum oxide as a catalyst support was grown on the Al plate surface via anodic oxidation in oxalic acid solution, and the internal surface area of the support was increased by pore widening and hot water treatments. To obtain a catalyst with high activity, multiple impregnations (>three times) and an anodization time of 24 h was needed. The catalyst was deactivated when operated at an elevated temperature of 623 K, but the activity was completely restored by a simple oxidation. Notably, OSRM was proven to be a combination of methanol combustion and methanol steam reforming reactions, and the kinetics of these two reactions were studied in detail.

engineering, chemical,chemistry, multidisciplinary
Mechanical exfoliation of boron carbide: A metal-free catalyst for aerobic oxidative desulfurization in fuel

Peiwen Wu,Qingdong Jia,Jing He,Linjie Lu,Linlin Chen,Jie Zhu,Chong Peng,Minqiang He,Jun Xiong,Wenshuai Zhu,Huaming Li

DOI: https://doi.org/10.1016/j.jhazmat.2020.122183

2020-06-05

Abstract:Metal-free catalysts have been proved to be a low-cost and environmentally friendly species in aerobic oxidative desulfurization (ODS). In this work, exfoliated metal-free boron carbide with few-layered structure, small size, and abundant defects, was first employed in an aerobic ODS system for ultra-deep desulfurization. The exfoliation process was realized by employing a planetary ball mill strategy. Detailed characterizations showed that the ball milling process not only induces thinner layers and small sizes but also introduces numerous defects into the boron carbide catalysts, which is vital in metal-free catalysis. Furthermore, the exfoliated boron carbide catalyst was applied in aerobic ODS system, and 99.5 % of sulfur removal was obtained. Moreover, the catalyst can be recycled 17 times without a significant decrease in catalytic activity. In particular, it was found that ∼90 % of the sulfur compounds in real diesel oil could be removed by the current aerobic ODS system.

The use of supercritical water for the catalyst-free oxidation of coarse aluminum for hydrogen production

Oxidation of coarse aluminum in pressured water steam for energy applications

Hydrogen production rates of aluminum reacting with varying densities of supercritical water

Experimental Study on Catalyst-Free High-Temperature and High-Pressure Aluminum-Water Reaction Characteristics Using Metal As Energy Carrier

Molten Salt-Enhanced Production of Hydrogen by Using Skimmed Hot Dross from Aluminum Remelting at High Temperature

Experimental study on characteristics and mechanism of hydrogen production from aluminium–water reaction for carbon-free power generation

Metal-Free Catalyst with Large Carbon Defects for Efficient Direct Overall Water Splitting in Air at Room Pressure

Borohydride Hydrolysis Using a Mechanically and Chemically Stable Aluminium‐Stainless Steel Porous Monolith Catalyst Made by 3D Printing

Experimental Investigation of the Catalyst-Free Reaction Characteristics of Micron Aluminum Powder with Water at Low and Medium Temperatures

Cogeneration of hydrogen, alumina, and heat from aluminum-water reactions

A Critical Assessment of Aluminium-Water Reaction for On-Site Hydrogen-Powered Applications

A microreactor with superhydrophobic Pt–Al2O3 catalyst coating concerning oxidation of hydrogen off-gas from fuel cell

An aluminum/cobalt/iron/nickel alloy as a precatalyst for water oxidation

Supercritical Water Synthesis of Bimetallic Catalyst and Its Application in Hydrogen Production by Furfural Gasification in Supercritical Water

Catalytic Hydrogen Production from Municipal Sludge in Supercritical Water with Partial Oxidation

Thermodynamics of oxidation of an alumina-supported cobalt catalyst by water in F-T synthesis

Oxidation Processes and Involved Chemical Reactions of Corrosion-Resistant Alloys in Supercritical Water

Upcycling of Cr-Containing Sulfate Waste into Efficient FeCrO3/Fe2O3 Catalysts for CO2 Hydrogenation Reaction

A comparison study on aluminum-water reaction with different catalysts

Anodic aluminum oxide supported Cu-Zn catalyst for oxidative steam reforming of methanol

Mechanical exfoliation of boron carbide: A metal-free catalyst for aerobic oxidative desulfurization in fuel