Abstract:In view of the difficult utilization of a large amount of coal-based solid waste produced by coal electrification in the Ningdong mining area, especially the large storage and low utilization rate of gasified slag, combined with the advantages of high paste filling concentration, fast efficiency, and low construction cost, it is of great significance to study the appropriate proportion of fly ash-based multicontent gasified slag paste filling material for green mining and large-amount utilization of gasified slag. Based on the microstructure, composition, and particle size distribution of gasification slag, fly ash, broken coal gangue, furnace bottom slag, and desulfurization gypsum tested by XRD, SEM, and particle size sorting screen, the mass fraction (X1), gasification slag content (X2), m (c): m (FA) (X3). 29 groups of schemes are designed by four factors : mass fraction X1 refers to the proportion of solid in the filling paste, the amount of gasification slag in the solid X2 refers to the proportion of gasification slag in the solid, and m (c): m (FA) X3 refers to the proportion of fly ash and cement in the solid excluding gasification slag, coal gangue, desulfurization gypsum, and furnace bottom slag. The amount of desulfurization gypsum in the solid X4 refers to the proportion of desulfurization gypsum in the solid. The flow and strength characteristics of each group are analyzed. It is found that before proportioning, coal gangue of 2.5∼5 mm accounts for 80.8%, furnace bottom slag of less than 2.5 mm accounts for 56.5%, fly ash of 20∼80% μm accounts for 80%, and fly ash of 10∼20% μm accounts for 90%. XRD patterns reveal that the main components of four solid wastes and cement are SiO2 and Ca3SiO5, and the chemical composition of desulfurization gypsum is Ca(SO4)(H2O)2. The regularity of size change tends to be consistent, and the uniaxial compressive strength of 3 days later in group thirteenth exceeds 0.991 MPa. Combined with the flow characteristics, it is determined that there are 6 optimization groups in the inclined ladder area with the expansion of 200∼250 mm and the uniaxial compressive strength of 0.6∼1.4 MPa. The compressive strength increases with the increase of the mass fraction of single-factor analysis. The response surface method of C shows that the significance of X1, X2, X3, and X4 decreases in turn. The central combination design is used to predict that the mix proportion of X1 is 84%, X2 is 15%, X3 is 1 : 5, and X4 is 7%, the content of coal gangue is 10%, and the content of furnace bottom slag is 5% which is the best. The supplementary experimental results show that σ3d is 1.35 MPa and the expansion is 200 mm. Combined with SEM, it is found that the microstructure before and after optimization is rich in hydration products and the internal structure is well cemented, which further explains σC. The above research provides important basic parameters for large-scale disposal and green filling mining which is difficult to deal with a large amount of stockpiled gasification slag.

Preparation of coal gangue-slag-fly ash geopolymer grouting materials

Experimental Study on Ratio and Performance of Coal Gangue/Bottom Ash Geopolymer Double-Liquid Grouting Material

Mechanical properties and solidification mechanism of coal gangue-granulated blast furnace slag geopolymer stabilized engineering slurry

Feasibility analysis of the preparation of geopolymers from different types of coal based ash: Reaction, synthesis, and properties

Compressive and Flexural Properties of Ultra-Fine Coal Gangue-Based Geopolymer Gels and Microscopic Mechanism Analysis

Preparation and curing method of red mud-calcium carbide slag synergistically activated fly ash-ground granulated blast furnace slag based eco-friendly geopolymer

Low-carbon wet-ground fly ash geopolymer activated by single calcium carbide slag

Preparation and performance optimization of fly ash- slag- red mud based geopolymer mortar: Simplex-centroid experimental design method

Designing low-carbon fly ash based geopolymer with red mud and blast furnace slag wastes: Performance, microstructure and mechanism

Properties of Gangue Powder Modified Fly Ash-Based Geopolymer

Microstructure Analysis and Effects of Single and Mixed Activators on Setting Time and Strength of Coal Gangue-Based Geopolymers

Preparation and microstructure analysis of alkali-activated ground granulated blast furnace slag-steel slag grouting materials

Mechanical behavior and microstructure evolution of slag-fly ash based geopolymer stabilized sand

Study on the Compressive Strength and Reaction Mechanism of Alkali-Activated Geopolymer Materials Using Coal Gangue and Ground Granulated Blast Furnace Slag

Optimization Analysis of Mechanical Properties of Fly Ash-Based Multicontent Gasification Slag Paste Filling Material

Formulation and properties of a new cleaner double liquid alkali-activated grouting material

An efficient approach for sustainable fly ash geopolymer by coupled activation of wet-milling mechanical force and calcium hydroxide

Geopolymer bricks prepared by MSWI fly ash and other solid wastes: Moulding pressure and curing method optimisation

Modeling and optimization of fly ash–slag-based geopolymer using response surface method and its application in soft soil stabilization

Investigation of mechanical, microscopic, and leaching properties of coal-based solid waste geopolymer mortar activated by soda residue and phosphogypsum

Research on the Rheological Properties and Diffusion Law of Coal-Based Solid Waste Geopolymer Grouting Material