Nanostructured cobalt antimonate: a fast responsive and highly stable sensing material for liquefied petroleum gas detection at room temperature

Satyendra Singh,Archana Singh,Ajendra Singh,Sanjeev Rathore,B. C. Yadav,Poonam Tandon

DOI: https://doi.org/10.1039/d0ra06208a

IF: 4.036

2020-01-01

RSC Advances

Abstract:Modulation in electrical resistance of the sensing layer due to interaction (adsorption and reactions) with LPG.

chemistry, multidisciplinary

What problem does this paper attempt to address?

A fast responsive and highly reproducible liquefied petroleum gas (LPG) detection of CuxZn1-xSb2O6 (x = 0, 0.2, 0.4, 0.6, and 0.8) nanostructures

Satyendra Singh,Gulshan Kumar

DOI: https://doi.org/10.1007/s10854-024-13963-w

2024-12-05

Journal of Materials Science Materials in Electronics

Abstract:A repeatable and fast responsive room temperature (25 °C) liquefied petroleum gas sensor has been demonstrated. Catalytic additives comprising Cu x Zn 1-x Sb 2 O 6 ( x = 0, 0.2, 0.4, 0.6, and 0.8) nanostructures were synthesised by the sol–gel technique for the first time. Spin-coated thin films were tested for liquefied petroleum gas detection at 25 °C. For analysing the obtained LPG sensing data, the as-synthesised materials were characterised using several relevant methodologies. The materials micro-structural characteristics were examined by scanning electron microscopy and X-ray diffraction. Vibrational modes were analysed using Fourier transform infrared (FTIR) spectroscopy. Optical characterisation was conducted using ultraviolet–visible (UV–Vis) spectroscopy. Among all the compositions of the synthesised Cu x Zn 1-x Sb 2 O 6 ( x = 0, 0.2, 0.4, 0.6, and 0.8) nanostructures, the Cu 0.8 Zn 0.2 Sb 2 O 6 thin film sensor exhibited the lowest resistance, owing to the optimal catalytic additive effect of copper, which include structural and chemical modifications. Even at ambient temperature, the Cu 0.8 Zn 0.2 Sb 2 O 6 thin film sensor responded well to lower explosive limit (LEL) of LPG which is attributed to optimised copper doping. The process by which catalytic inclusion boost the LPG sensing characteristics was also established. Long-term analysis of sensing characteristics up to 90 days revealed the consistency and reliability of fabricated sensor.

engineering, electrical & electronic,materials science, multidisciplinary,physics, condensed matter, applied
Room temperature LPG sensing of highly responsive Ag-doped CuO: SnO 2 nanocomposite film.

Vernica Verma,N.K. Pandey,Ajeet Singh,Peramjeet Singh,Shivangi Srivastava,Neetu Yadav,Amit Kumar Verma,Shriya Tripathi

DOI: https://doi.org/10.1016/j.physe.2024.116035

2024-06-26

Physica E: Low-Dimensional Systems and Nanostructures

Abstract:The designed nanocomposite film of self-assembled 2D Ag-doped CuO:SnO 2 nanoflakes have been successfully synthesized through facile one-step hydrothermal technique. The fabricated sensor film is developed to detect liquefied petroleum gas (LPG) at room temperature. X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), Raman spectroscopy, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and UV-visible spectroscopy comprehensively characterize the film's microstructure, morphology, element composition, and optical properties. The LPG sensing outcomes reveal that the Ag-doped CuO:SnO 2 film based sensor exhibits exceptional response and excellent repeatability towards LPG at room temperature. This is predominantly due to formation of CuO: SnO 2 interface, sensitized by doping silver (Ag) that drastically increases the carrier concentration of the NC sensor film and provides superior ability to detect LPG across a range of concentrations at room temperature. The sensor response increases from 300% for 0.5 vol.% LPG to a maximum of 414% at 2.0 vol.%. Notably, the sensor demonstrates fast response and recovery times (21 s and 30 s for 0.5 vol.% LPG). These promising attributes position the NC sensor film as a strong candidate for real-world LPG sensing applications. Additionally, the research proposes a comprehensive mechanism explaining the NC sensor film's detection performance.

physics, condensed matter,nanoscience & nanotechnology
Nanocomposite of Cobalt Oxide Nanocrystals and Single-Walled Carbon Nanotubes for A Gas Sensor Application

Wei Li,Hyuck Jung,Nguyen Duc Hoa,Dojin Kim,Soon-Ku Hong,Hyojin Kim

DOI: https://doi.org/10.1016/j.snb.2010.07.023

2010-01-01

Abstract:A polymer-assisted deposition method was used to prepare nanocomposite structures of cobalt oxide and single-walled carbon nanotubes (SWCNTs) for a gas sensor application. Scanning electron microscopy images show that the deposition morphology of Co3O4 is closely related to the viscosity and metal ion concentration in the precursor solution. X-ray diffraction data combined with Raman spectra show that the composite film has high crystalline quality. The basic sensing behavior was evaluated with NOx gas as an electron-accepting gas and H2 as an electron-donating gas. The composite shows a response of ∼200% upon exposure to 4% H2 at room temperature. This value is higher than that observed in SWCNT thin film and Co3O4 film, as well as in other pure and functionalized CNTs. The enhancement may have originated from the combination of the nature of Co3O4 particles that actively react with gases and the formation of an electrical continuum between Co3O4 and SWCNTs.
Highly Sensitive, Ambient Temperature CO Sensor using Tin Oxide based Composites

Vinay Kishnani,Gulshan Verma,Ankur Gupta

DOI: https://doi.org/10.31224/osf.io/uvnst

2021-06-18

Abstract:In the present work, we report an excellent gas sensing performance of the unique nanocomposite films prepared with the help of different materials such as semiconductor metal-oxide, polymer and metal for carbon monoxide gas sensing at ambient temperature. The fabrication of SnO2/PANI/Pd nanocomposite film was performed using the hydrothermal route. The fabricated films were characterized with various analytical techniques such as X-ray diffraction (XRD), Field emission scanning electron microscope (FESEM), and Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR) etc. Furthermore, DFT results are used to examine the transport and electronic properties of all prepared films. The computing results show that after hybridizing with Pd and SnO2, the response of the fabricated SnO2 and polyaniline (PANI) films to CO gas molecules is considerably improved. At room temperature, sensing characterization of the fabricated sensing films was carried out by using target gas concentrations with varying ppm level of 50 to 300. At ambient temperature, the SnO2/PANI/Pd film has the maximum sensitivity ~400.8% out of all the fabricated films at 0.3% of the target gas. Our findings show that SnO2, SnO2/Pd, PANI, and SnO2/PANI/Pd composite sensing films have a bright future in the gas sensing application with incredibly-higher sensitivity towards CO gas.
Tailoring the surface morphology of nanostructured cobalt oxide for high-sensitivity CO sensor

Muidh Alheshibri,N. M. Shaalan,Q. A. Drmosh,Abbad Al Baroot,Sultan Akhtar,A. Aljaafari,Hassan S. Al Qahtani,Khaled Elsayed

DOI: https://doi.org/10.1007/s10853-022-07438-8

IF: 4.5

2022-07-04

Journal of Materials Science

Abstract:The development of efficient carbon monoxide (CO) gas sensors with earth abundance and low cost is very important in gas sensing applications. The cobalt oxide material with various morphologies and structures demonstrates different gas sensing properties. In this work, different morphologies of nanostructured spinel cobalt oxide (Co 3 O 4 ) have been synthesized by pulsed laser ablation in liquid media (PLAL) using high-purity cobalt as a target in several ethanol/water mixtures. The gas properties of the fabricated Co 3 O 4 -based sensors were investigated toward CO gas at various gas concentrations and operating temperatures. Several characterization techniques including TEM, XRD, XPS, and Raman spectroscopy were utilized to study the chemical and physical properties of the fabricated samples. The obtained results displayed that the morphology of the nanostructured Co 3 O 4 could be controlled by altering the ethanol concentrations in the ablation media. Compared with the Co 3 O 4 nanoparticles prepared by laser ablation in water, the Co 3 O 4 nanosheets/flakes prepared at 70% ethanol exhibited superior sensitivity characteristics. A sensitivity of 360% was achieved at 300 °C and 200 ppm of CO. These results reordered for Co 3 O 4 nanosheets/flakes demonstrate a brand-new approach for the fabrication of low-detection-limit CO sensors.

materials science, multidisciplinary
Carbon Monoxide (CO) Sensor Based on Au Nanoparticles Embedded in a CuO Matrix by HR-LSPR Spectroscopy at Room Temperature

J. Borges,F. Vaz,M. Proença,M. Rodrigues

DOI: https://doi.org/10.1109/LSENS.2021.3074603

2021-05-01

IEEE Sensors Letters

Abstract:Optical gas sensors have emerged as an alternative to conventional conductometric sensors, opening new possibilities, especially for the detection of polluting and/or toxic molecules, such as carbon monoxide (CO). In this letter, an optimized plasmonic thin film, composed of Au nanoparticles embedded in a CuO matrix, was tested as a CO sensor, using high-resolution localized surface plasmon resonance (LSPR) spectroscopy. The Au:CuO thin film system was found to be highly sensitive, exhibiting a fast (∼14 s) and reversible (∼50 s) response when exposed to 50 ppm of CO, working at room temperature. Furthermore, the Au:CuO thin film prototype sensor presented a signal-to-noise ratio of 11, calculated at the transmittance minimum of the LSPR band, which allowed estimation of a detection limit as low as 14 ppm for CO gas.

Environmental Science,Chemistry,Materials Science
Ultrahigh sensitive and selective room-temperature carbon monoxide gas sensor based on polypyrrole/titanium dioxide nanocomposite

Maamon A. Farea,Gita B. Bhanuse,Hamed Y. Mohammed,Mohammed O. Farea,Mohyeddine Sallam,Sumedh M. Shirsat,Meng-Lin Tsai,Mahendra D. Shirsat

DOI: https://doi.org/10.1016/j.jallcom.2022.165397

IF: 6.2

2022-10-05

Journal of Alloys and Compounds

Abstract:In this article, an ultrahigh sensitive and selective carbon monoxide (CO) gas sensor was developed and studied at room temperature utilizing the PPy/TiO2 nanocomposite. The gas sensors were fabricated through drop-casting the PPy/TiO2 nanocomposites on the surface of interdigitated electrodes. All the nanocomposites have been synthesized via a chemical oxidation method. Contrary to the pure PPy sensor, PPy/TiO2 sensor exhibited 4-fold enhanced sensitivity. Our sensor showed a superior response of order 93 at 270 ppm of carbon monoxide with high selectivity over the other interference gases. Additionally, our sensor exhibited a quick response time and a short recovery time of 36 s and 38 s, long-term stability, excellent repeatability, and satisfactory reproducibility. Accordingly, experimental findings proved that incorporating TiO2 into the PPy plays an influential role in enhancing the gas sensor performance. In this work, based on the outstanding CO sensing performance, the PPy/TiO2-based sensor might be considered a promising candidate for real-time gas sensor applications.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Low concentration CO gas sensor constructed from MoS2 nanosheets dispersed SnO2 nanoparticles at room temperature under UV light

Yang Li,Xingyuan Song,Lili Li,Wei Wu,Kai Tao,Kai Tao,Zhihua Ying,Yongqian Hu,Yang Zhou,Ranran Zhang,Gaofeng Wang,Fei Wen

DOI: https://doi.org/10.1016/j.ceramint.2022.11.204

IF: 5.532

2023-04-01

Ceramics International

Abstract:In consideration of the different electron structure-associated physical properties and internal sensing merits of MoS2 and SnO2, this work reports a nanocomposite with unique structure of MoS2 nanosheets dispersed SnO2 nanoparticles. The sensing performance of MoS2/SnO2 sensor toward low concentration CO was investigated at room temperature under the UV light illumination. It was found that MoS2/SnO2 sensor shows improved CO gas response (R ~ 4.97 at 40 ppm CO) compared with pure SnO2 (R ~ 3.27 at 40 ppm CO), which is due to the unique structure and the formation of heterostructure between MoS2 and SnO2. Moreover, the fabricated sensor also exhibits fast response and recovery time (43 s/36 s). The sensor provides a potential platform for monitoring CO gas at room temperature.

materials science, ceramics
Nanoscale Engineering of Polypyrrole-Silver Oxide Composites for Rapid and Ultrasensitive Room Temperature Carbon Monoxide Detection

Hamed Y. Mohammed,Maamon A. Farea,Mahyoub H. Albuhairi,Mahendra D. Shirsat

DOI: https://doi.org/10.1016/j.synthmet.2024.117546

IF: 4

2024-01-20

Synthetic Metals

Abstract:In this work, a silver oxide decorated Polypyrrole (Ag 2 O@Ppy) composites-based sensor was fabricated, for the first time, via a simple solution mixing method. Extensive materials characterization, via XRD, AFM, SEM, UV–vis, FTIR, and Raman spectroscopies, elucidated the tailored nanoarchitecture, unveiling Ag 2 O nanoparticle decoration homogenously encapsulating Ppy matrices. Systematic comparative gas sensing analysis demonstrated remarkably high sensitivity and selectivity towards CO versus other hazardous species (NH 3 , NO 2 , H 2 S, SO 2 ). A superb 387% response at 300 ppm CO was achieved, significantly exceeding other gases. Remarkably, outstanding 156% response even at ultralow 10 ppm concentration reflected an exceptional limit of detection rivaling most sensors. Rapid, reversible response kinetics with 111 s reaction and 66 s recovery times arose from synergistic coupling between Ppy and Ag 2 O nanoparticles enabling expedited charge transfer. Excellent linearity spanned an ultrawide 10-600 ppm range. Unprecedented performance combined sensitivity, selectivity, speed, stability, and ambient temperature operation. The work unveils tremendously promising Ppy-Ag 2 O nanocomposites for next-generation chemiresistive CO monitoring critical for environmental safety and healthcare.

materials science, multidisciplinary,physics, condensed matter,polymer science
Synthesis and Characterization of Flower-Like Cobalt-Doped ZnO Nanostructures for Ammonia Sensing Applications

B. Himabindu,N. S. M. P. Latha Devi,P. Nagaraju,B. Rajini Kanth,Himabindu Bantikatla,LathaDevi N.S.M.P.,Nagaraju Pothukanuri,B. Rajani kanth

DOI: https://doi.org/10.1149/2162-8777/ad26a3

IF: 2.2

2024-02-08

ECS Journal of Solid State Science and Technology

Abstract:The present study uses the co-precipitation method to explore the synthesis of zinc oxide and cobalt-doped ZnO sensors, encompassing a range of cobalt concentrations from 1 to 4 wt.%. The synthesized samples undergo comprehensive analysis to evaluate their structural, morphological, optical, and gas-sensing properties. X-ray diffraction revealed a hexagonal Wurtzite structure, and the crystallite size decreased from 16.92 to 15.39 nm. Energy-dispersive X-ray spectroscopy and Fourier-transform infrared spectroscopy collectively affirmed the presence of cobalt. Scanning electron microscopy was used to analyze the morphological characteristics. The Tauc-plot was used to determine the optical bandgap via diffuse reflectance spectroscopy. As cobalt doping increased, the band gap increased from 3.18 to 3.23 eV. Further, atomic force microscopy and Brunauer-Emmett-Teller analysis were used to assess the surface topography and pore size distribution. The AFM measurements indicated roughness within 435-700 nm. The BET analysis revealed mesoporous properties, with surface area ranging between 18.657 to 21.962 m2/g. Subsequently, the gas-sensing capabilities of the Co-doped ZnO sensors were examined for various volatile organic compounds at room temperature. The sensor with 4% Cobalt doping exhibited a fast response and recovery time of 21 and 20 seconds for 2 ppm of NH3

materials science, multidisciplinary,physics, applied
A surface passivated fluorinated polymer nanocomposite for carbon monoxide resistant plasmonic hydrogen sensing

I. Östergren,I. Darmadi,S. Lerch,R. R. da Silva,M. Craighero,S. H. K. Paleti,K. Moth-Poulsen,C. Langhammer,C. Müller

DOI: https://doi.org/10.1039/d4ta00055b

IF: 11.9

2024-01-01

Journal of Materials Chemistry A

Abstract:Core:shell architecture of Teflon AF:Pd coated with PMMA, which generates a protective barrier against carbon monoxide, simultaneously allowing fast and selective hydrogen sensing.

materials science, multidisciplinary,chemistry, physical,energy & fuels
Rapid chemiresistive detection of p-nitrophenol through Porphyrin-functionalized 2D materials: a step toward environmental monitoring

Jyoti Gupta,Dhana Sai Shree Kandkuri,Sunita Rattan

DOI: https://doi.org/10.1007/s10853-023-09283-9

IF: 4.5

2024-02-24

Journal of Materials Science

Abstract:Chemiresistive gas sensors have gained attention due to their simple device structure, portability, easy fabrication, and operation. However, one of the major drawbacks of these sensors is their lack of selectivity and low sensing response. The p–n junction-based vapor sensors are gaining significant attention all over the world for their enhanced sensing response and selectivity toward vapor sensing compared to ohmic contact-based chemiresistive sensors. In the present work, attempts have been made to develop the p–n junction-based chemiresistive sensor through interface modulation of nano graphite platelets (NGPs) using functionalized two-dimensional (2D) materials, resulting in the formation of a p–n junction. The nanocomposite sensor has been developed through octaethyl cobalt porphyrin-functionalized nano graphite platelets (OEP-Co-NGPs) (n-type) with tungsten disulfide nanoparticles (WS 2 NPs) (p-type) and analyzed with multiple characterization techniques, including Raman spectroscopy, X-ray diffractometer (XRD), scanning electron microscopy (SEM), contact angle, etc. In this work, both NGPs/WS 2 and OEP-Co-NGPs/WS 2 sensors have been employed for para-nitrophenol (p-NP) vapor detection. The experimental results demonstrated that the OEP-Co-NGPs/WS 2 sensor exhibited an excellent sensing response toward selective detection of p-nitrophenol (p-NP). The creation of the p–n junction through porphyrin-functionalized NGPs into heterostructure has significantly improved the sensing response as compared to the sensor prepared through non-functionalized NGPs. The OEP-Co-NGPs/WS 2 sensor exhibited excellent selectivity even in the presence of inferring gas species, low limiting detection of 0.0459 ppb, excellent repeatability, reproducibility (relative standard deviation (RSD)-0.845%), long-term stability (RSD < 3.01%), and outstanding linearity (coefficient of correlation ( R 2 )—0.909). It also showed a high tolerance to humidity due to the hydrophobic nature of OEP-Co-NGPs. Further, the charge transport mechanism has been studied through a variable range hopping (VRH) model along with the temperature-dependent electrical conductivity of the OEP-Co-NGPs/WS 2 nanocomposite. Thus, the n–p junction-based OEP-Co-NGPs/WS 2 chemiresistive sensor has the potential to be used as a novel p-NP vapor detector that provides excellent performance with good tolerance to environmental humidity.

materials science, multidisciplinary
Design and Analysis of Various Characteristics of a MEMS-Based PIB/CNT/LiNbO3 Multilayered SAW Sensor for CO2 Gas Detection

Ashish Tiwary,Shasanka Sekhar Rout,Basudeba Behera

DOI: https://doi.org/10.1007/s42341-022-00392-x

2022-03-22

Transactions on Electrical and Electronic Materials

Abstract:This paper presents the design and analysis of a surface acoustic wave (SAW) sensor with a multilayer nanocomposite to detect carbon dioxide (CO2) gas. SAW resonator impacts the detection and identification of hazardous gases that exist in the environment in an uncontrolled manner. These devices have the operational capability to work in a very extreme elevated temperature, pressure, and inert noxious atmosphere. The proposed work is intended to provide a two-dimensional model of a surface acoustic wave device/sensor and the most prominent solid material, carbon nanotube (CNT), which plays a vital role in the adsorption of volatile organic compounds. However, another miniature sensor has been designed with a potential material, an organic polymer, i.e., poly-isobutylene (PIB). Both the sensor model responses were examined for CO2 gas at room temperature. In this work, we have designed two different resonator structures with the help of COMSOL Multiphysics. The proposed, designed models were patterned with interdigitated transducer electrodes made of aluminum material coated explicitly on top of the structure were used to analyze gas sensing behavior for CO2 gaseous elements. Here the proposed geometry provides resonance of 9.1524 MHz and anti-resonance of 9.2455 MHz for monolayer structure and resonance of 8.6447 MHz, and anti-resonance of 8.5201 MHz for multilayer structure. Comparatively, the second sensor PIB/CNT/LiNbO3 heterostructure pattern was also designed to be the best choice for the accurate and reliable measurement of the concentration of various gaseous elements based on a few parameters are discussed further.
Sensors: Pt Nanoparticles Sensitized Ordered Mesoporous WO <sub>3</sub> Semiconductor: Gas Sensing Performance and Mechanism Study (Adv. Funct. Mater. 6/2018)

Junhao Ma,Yuan Ren,Xinran Zhou,Liangliang Liu,Yongheng Zhu,Xiaowei Cheng,Pengcheng Xu,Xinxin Li,Yonghui Deng,Dongyuan Zhao

DOI: https://doi.org/10.1002/adfm.201870040

IF: 19

2018-01-01

Advanced Functional Materials

Abstract:In article number 1705268, Yonghui Deng and co-workers report the rational design and synthesis of Pt nanoparticles sensitized ordered mesoporous WO3. A facile co-assembly strategy results in superior performance in carbon monoxide sensing owing to the rationally combined merits of the high porosity of mesoporous WO3 and the chemical and electronic sensitization effects of Pt.
A Monolithic Nano-Scale Sensor Architecture with Tuneable Gas Diffusion for Molecular Fingerprinting

Alishba Tanya John,Mahdiar Taheri,Jodie Yuwono,Priyank Vijaya Kumar,David Nisbet,Krishnan Murugappan,Antonio Tricoli

DOI: https://doi.org/10.1039/d3ta07282g

IF: 11.9

2024-02-22

Journal of Materials Chemistry A

Abstract:Semiconducting metal oxide (SMO) gas sensors have emerged as invaluable technology due to their high sensitivity and ease of fabrication. However, they have limited selectivity and require relatively high operational temperatures. Here, we present a monolithic membrane-chemoresistive sensor consisting of a hierarchical metal oxide (MO) and a metal-organic frameworks (MOF) layer. Both layers were made by sequential aerosol deposition of SnO 2 and ZnO nanoparticles, with the latter being thereafter converted to zeolitic imidazolate framework (ZIF-8) by chemical vapour conversion. The SnO 2 fractal network provides high surface area for chemical sensing, while the multi-scale porous ZIF-8 membrane offers a controlled gateway for gas molecule diffusion. Notably, our hierarchical dual-layer architecture can tune the analyte sensor response time, allowing discrimination of a variety of gases, including NO 2 , ethanol, acetone, methanol, propane, and ethyl benzene. Density Functional Theory (DFT) calculations were implemented to gain further insights into the selectivity mechanism revealing the key role of surface adsorption sites. This approach enables us to develop unique response profiles, fingerprinting the presence of specific gas molecules, with application ranging from industrial safety to environmental monitoring and medical diagnostics.

materials science, multidisciplinary,chemistry, physical,energy & fuels
Structural study and gas sensing application of nanocrystalline mixed ferrites synthesized by auto-combustion method

Laxmi J. Hathiya,Deepshikha Rathore,Meenu Khan,Hiren. H. Joshi

DOI: https://doi.org/10.1007/s10854-024-13586-1

2024-09-28

Journal of Materials Science Materials in Electronics

Abstract:The present research work reports the synthesis of nanocrystalline nickel ferrite and its composition with manganese ferrite by employing the citrate-gel auto-combustion route to study the structural properties and gas sensing application. The gas sensing devices were successfully synthesized in the form of pellets to study their response toward the target gases. The stoichiometry of ferrite powders is confirmed by EDAX analysis. The crystallite size, porosity, and other structural parameters were deduced by XRD analysis. The average particle size obtained by TEM measurement was compared with crystallite size. The basic characteristics of spinel ferrites were studied by FTIR analysis. The optical bandgap energy value of samples was found by UV–Vis. DRS analysis. The gas sensing experiment was performed successfully to study the gas response (%) at different gas concentrations (ppm) and temperatures (°C). The maximum sensitivity (S max ) of around 99% was exhibited by Mn 0.8 Ni 0.2 Fe 2 O 4 at different temperatures.

engineering, electrical & electronic,materials science, multidisciplinary,physics, condensed matter, applied
ZnO Based Ultrasensitive CO Chemiresistive Gas Sensor

Shivani Dhall,Kapil Sood,Jyoti Prakash,B.R. Mehta

DOI: https://doi.org/10.1088/1402-4896/ad3d8e

2024-04-12

Physica Scripta

Abstract:The detection of environmental gases in the atmosphere is a topic of interest for public security, environmental pollution and industrial emission. In recent years, semiconductor-based gas sensor attracted wide attention in all over the world. Among various hazardous gases, detection of CO at low temperature with fast response and recovery time is still a challenge. In this work, we have adopted single step synthesis of zinc oxide (ZnO) nanoroads for the fabrication of CO gas sensor. This sensor is found to have ~8% sensitivity with fast response time of the order of 10s at 50C. Also, selectivity of these sensors has been investigated for different gases and observed that ZnO are more active for CO gas at 50C. The sensitivity of ZnO based sensor is explained in terms of interaction of CO molecules with adsorbed oxygen vacancies in ZnO which promote better pathway to the charge carrier. The sensing material was characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). To, the best our knowledge, the detection of 15 ppm CO at 50 with good sensitivity is reported first time.

physics, multidisciplinary
Enhanced Sensing Performance of Electrospun Tin Dioxide Nanofibers Decorated with Cerium Dioxide Nanoparticles for the Detection of Liquefied Petroleum Gas

Xichen Liu,Jianhua Zhang,Hao Zhang,Can Chen,Dongzhi Zhang

DOI: https://doi.org/10.3390/chemosensors10120497

2022-11-23

Chemosensors

Abstract:Tin dioxide (SnO2) nanofibers and cerium dioxide (CeO2) nanoparticles were prepared by electrospinning and hydrothermal methods, respectively. The morphology and structure of the synthesized SnO2/CeO2 samples were characterized by a variety of methods. The gas-sensing properties of the SnO2/CeO2 sensor were investigated for liquefied petroleum gas (LPG) detection at room temperature. Compared with pure SnO2 nanofibers, the SnO2/CeO2 composite sensor showed a much higher response and shorter response time for LPG sensing after doping with CeO2 nanoparticles. Furthermore, the SnO2/CeO2 composite sensor had better resistance to interference from humidity than the pure SnO2 sensor. The significantly enhanced sensing performance of the SnO2/CeO2 composite sensor for LPG can be attributed to the modification with CeO2 to increase oxygen vacancies and form a heterostructure with SnO2 nanofibers. Meanwhile, the LPG detection circuit was built to realize real-time concentration display and alarm for practical applications.

chemistry, analytical,electrochemistry,instruments & instrumentation
Palladium-Doped Tin Oxide Nanosensor for the Detection of the Air Pollutant Carbon Monoxide Gas

Jeyapaul Sam Jebakumar,Asokan Vimala Juliet

DOI: https://doi.org/10.3390/s20205889

IF: 3.9

2020-10-17

Sensors

Abstract:The exhaust gases from various sources cause air pollution, which is a leading contributor to the global disease burden. Hence, it has become vital to monitor and control the increasing pollutants coming out of the various sources into the environment. This paper has designed and developed a sensor material to determine the amount of carbon monoxide (CO), which is one of the major primary air pollutants produced by human activity. Nanoparticle-based sensors have several benefits in sensitivity and specificity over sensors made from traditional materials. In this study, tin oxide (SnO2), which has greater sensitivity to the target gas, is selected as the sensing material which selectively senses only CO. Tin oxide nanoparticles have been synthesized from stannous chloride dihydrate chemical compound by chemical precipitation method. Palladium, at the concentration of 0.1%, 0.2%, and 0.3% by weight, was added to tin oxide and the results were compared. Synthesized samples were characterized by X-ray diffraction (XRD) and field emission scanning electron microscope (FESEM) techniques. XRD revealed the tetragonal structure of the SnO2 nanoparticles and FESEM analysis showed the size of the nanoparticles to be about 7–20 nm. Further, the real-time sensor testing was performed and the results proved that the tin oxide sensor, doped with 0.2% palladium, senses the CO gas more efficiently with greater sensitivity.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Recent Progress in Chemiresistive Gas Sensing Technology Based on Molybdenum and Tungsten Chalcogenide Nanostructures

Ravindra Kumar Jha,Navakanta Bhat

DOI: https://doi.org/10.1002/admi.201901992

IF: 5.4

2020-04-01

Advanced Materials Interfaces

Abstract:Chalcogens are oxygen family elements with oxygen having distinct properties than the other group members like sulfur, selenium, and tellurium. Tungsten and molybdenum chalcogenides that include mainly metal oxides (MO3; M = Mo, and W) and metal dichalcogenides (MX2; X = S, Se, and Te) are the most exciting class of inorganic materials. They have been widely investigated in various applications including lithium and sodium ion storage, supercapacitors, gas sensors, biosensors etc. due to their fascinating surface properties and ease of fabrication. Different class of nanostructures including 0D (nanoparticles, quantum dots), 1D (nanowires, nanotubes, nanoribbons, nanobelts etc.), and 2D (nanosheets, nanoflakes, nanoplates etc.) structures of these materials have been synthesized, characterized, and utilized for these applications. With recent boost in layered material research, they are also being reconsidered for future device and systems applications. In this review article, the recent developments on the chemiresistive gas sensing applications of these nanomaterials are discussed. The authors also outline the efforts which have been made over the years to improve the sensing behavior of these materials. Finally, the authors present future opportunities in realizing high‐performance gas sensors using these materials.

materials science, multidisciplinary,chemistry

Nanostructured cobalt antimonate: a fast responsive and highly stable sensing material for liquefied petroleum gas detection at room temperature

A fast responsive and highly reproducible liquefied petroleum gas (LPG) detection of CuxZn1-xSb2O6 (x = 0, 0.2, 0.4, 0.6, and 0.8) nanostructures

Room temperature LPG sensing of highly responsive Ag-doped CuO: SnO 2 nanocomposite film.

Nanocomposite of Cobalt Oxide Nanocrystals and Single-Walled Carbon Nanotubes for A Gas Sensor Application

Highly Sensitive, Ambient Temperature CO Sensor using Tin Oxide based Composites

Tailoring the surface morphology of nanostructured cobalt oxide for high-sensitivity CO sensor

Carbon Monoxide (CO) Sensor Based on Au Nanoparticles Embedded in a CuO Matrix by HR-LSPR Spectroscopy at Room Temperature

Ultrahigh sensitive and selective room-temperature carbon monoxide gas sensor based on polypyrrole/titanium dioxide nanocomposite

Low concentration CO gas sensor constructed from MoS2 nanosheets dispersed SnO2 nanoparticles at room temperature under UV light

Nanoscale Engineering of Polypyrrole-Silver Oxide Composites for Rapid and Ultrasensitive Room Temperature Carbon Monoxide Detection

Synthesis and Characterization of Flower-Like Cobalt-Doped ZnO Nanostructures for Ammonia Sensing Applications

A surface passivated fluorinated polymer nanocomposite for carbon monoxide resistant plasmonic hydrogen sensing

Rapid chemiresistive detection of p-nitrophenol through Porphyrin-functionalized 2D materials: a step toward environmental monitoring

Design and Analysis of Various Characteristics of a MEMS-Based PIB/CNT/LiNbO3 Multilayered SAW Sensor for CO2 Gas Detection

Sensors: Pt Nanoparticles Sensitized Ordered Mesoporous WO <sub>3</sub> Semiconductor: Gas Sensing Performance and Mechanism Study (Adv. Funct. Mater. 6/2018)

A Monolithic Nano-Scale Sensor Architecture with Tuneable Gas Diffusion for Molecular Fingerprinting

Structural study and gas sensing application of nanocrystalline mixed ferrites synthesized by auto-combustion method

ZnO Based Ultrasensitive CO Chemiresistive Gas Sensor

Enhanced Sensing Performance of Electrospun Tin Dioxide Nanofibers Decorated with Cerium Dioxide Nanoparticles for the Detection of Liquefied Petroleum Gas

Palladium-Doped Tin Oxide Nanosensor for the Detection of the Air Pollutant Carbon Monoxide Gas

Recent Progress in Chemiresistive Gas Sensing Technology Based on Molybdenum and Tungsten Chalcogenide Nanostructures