Abstract:In some traditional formative and additive manufacturing processes widely used in the fabrication of steel products, stress conditions and metallurgy typically result in a strong texture and mechanical anisotropy in both rolling high-strength low-alloy steel and additive manufacturing stainless steel products. To resolve this problem, we have investigated the effectiveness of a novel wire-arc additive manufacturing method in which the heat source is substituted by high-efficiency submerged arc plasma i.e., submerged arc additive manufacturing. An isotropic microstructure can be obtained in the bulk of large-scale low-carbon steel components by ensuring a complete columnar-to-equiaxed transition. We found that the top zone of the as-deposited component comprised columnar α-Fe grains with a typical preferential <001>α orientation. Multiple allotropic transformations were triggered by an in-situ intrinsic heat treatment (mainly the combination of multi-layer-penetration normalizing, full-layer-penetration inter-critical annealing, and long-duration tempering—i.e., NIT). Consequently, when the net bead height was no greater than the width of the fine grain zone affected by the previous layer of deposition, the microstructures in each new layer could be progressively refined and homogenized. Therefore, the intermediate zone was predominantly composed of fully equiaxed α-Fe and displayed homogeneous characteristics along the build direction. During full-layer NIT treatment, the pearlite was spheroidized slightly, reduced both in size (from 4μm to 2μm) and in area fraction (from ~5% to ~1%), thereby mitigating cracking susceptibility. Moreover, not only were the intracrystalline dislocations significantly reduced, but also their morphology evolved from tangled to movable lines. These changes, along with finer grains and the formation of high-angle grain boundaries, led to lower and more dispersed internal strain in the α-Fe matrix. Consequently, excellent Charpy toughness (over 300 J at -60 °C) with minimal deterioration in strength was achieved. Impact, tensile, and hardness tests revealed nearly isotropic mechanical characteristics. We believe that this novel method shows tremendous promise in large-scale additive manufacturing.

On the use of gas-metal-arc-welding additive manufacturing for repurposing of low-carbon steel components: microstructures and mechanical properties

Microstructure and Mechanical Properties of 304L Steel Fabricated by Arc Additive Manufacturing

A preliminary study on gas metal arc welding-based additive manufacturing of metal parts

Improve the Manufacturing Efficiency of Steel Bars by Using Hot-Wire Pulse Arc Additive Manufacturing

Remanufacturing of Low-Carbon Steel Components using WAAM: Microstructural, Mechanical, and Parametric Analysis

A study on wire and arc additive manufacturing of low-carbon steel components: process stability, microstructural and mechanical properties

Microstructure and Mechanical Properties of NiCrMoV Steel Fabricated by Double-Electrode Gas Metal Arc Additive Manufacturing

Microstructure and Mechanical Properties of High-Strength, Low-Alloy Steel Thin-Wall Fabricated with Wire and Arc Additive Manufacturing

Submerged arc additive manufacturing (SAAM) of low-carbon steel: Effect of in-situ intrinsic heat treatment (IHT) on microstructure and mechanical properties

Effect of welding parameters on microstructure and mechanical properties of mild steel components produced by WAAM

EFFECTS OF WELDING CURRENT ON THE SHAPE AND MICROSTRUCTURE FORMATION OF THIN-WALLED LOW-CARBON PARTS BUILT BY WIRE ARC ADDITIVE MANUFACTURING

Evaluation of thermal and geometric properties of martensitic stainless steel thin walls built by additive manufacturing cold metal transfer (CMT) processes

Experimental study of shielding gas concentration on mechanical properties of stainless steel alloy parts using wire and arc additive manufacturing

Influences of the process parameter and thermal cycles on the quality of 308L stainless steel walls produced by additive manufacturing utilizing an arc welding source

Microstructure and Mechanical Properties of Low-Carbon High-Strength Steel Fabricated by Wire and Arc Additive Manufacturing

Wire Arc Additive Manufacturing (WAAM) of Aluminum Alloy AlMg5Mn with Energy-Reduced Gas Metal Arc Welding (GMAW)

A Comparative Study of Microstructural Characteristics and Mechanical Properties of High-Strength Low-Alloy Steel Fabricated by Wire-Fed Laser Versus Wire Arc Additive Manufacturing

Microstructure Evolution and Mechanical Properties of New Co-free Maraging Steel Produced by Wire Arc Additive Manufacturing

Development of microstructure and mechanical properties of TiAl6V4 processed by wire and arc additive manufacturing

Forming Characteristics of Thin-Wall Steel Parts by Double Electrode GMAW Based Additive Manufacturing

Mechanical and microstructural features of wire-and-arc additively manufactured carbon steel thick plates