Abstract:The current study investigates the relationship between the microstructural and structural characteristics of dissimilar gas tungsten arc welding (GTAW) between Inconel 718 (IN 718) and austenitic stainless steel 304L (ASS 304L) using Inconel 625 (IN 625) as a filler material. The microstructural characterization of the dissimilar weld includes the application of an optical microscope (OM), field emission scanning electron microscopy (FE-SEM) including energy dispersive spectroscopy (EDS), and electron backscatter diffraction (EBSD). The optical and FESEM analysis of the base metals (BM) indicates the austenitic nature of the IN 718 BM matrix, which incorporates strengthening precipitates γ' and γ'' distributed throughout the Nickel matrix. In contrast, the ASS 304L BM exhibits an austenitic microstructure along with twins. Moreover, IN 625 weld metal exhibits austenitic microstructure in the form of cellular, columnar, and equiaxed dendrites. Elemental segregation demonstrates the existence of Nb, and Mo-rich carbides, including the laves phases at the interdendritic regions of the IN 625 weld zone and IN 718 Heat-Affected Zone (HAZ). Ferrite stringers were noticed in the HAZ of ASS 304L. EBSD analysis shows the improved texture of the weld zone exhibiting fine equiaxed recrystallized microstructures. EBSD/Kernel average misorientation (KAM) micrographs reveal the existence of high strain at the weld metal grain boundaries. Vickers microhardness assessment of the dissimilar weld demonstrates the high hardness of 257.5 HV for the IN 625 weld zone because of the occurred NbC, laves phases, and Mo-rich carbides. Room temperature tensile characterization shows the failure of tensile specimens from ASS 304L BM reflecting the high strength of the IN 625 weld metal (662 MPa). Tensile tests at high temperatures were performed at 550o C, 600o C, and 650o C. High-temperature tensile result exhibits a higher tensile strength of IN 625 weld zone than the ASS 304L BM, as the tensile specimens fails from 304L BM. The specimen exposed at 550o C exhibits the highest tensile strength of 388 MPa. The Charpy impact toughness test was conducted, with notches at the HAZ of ASS 304L, HAZ of IN 718, and the weld center being evaluated. The toughness value of the weld metal decreases (99 J) due to occurrence of the secondary precipitates. To analyze residual stress, the deep hole drilling (DHD) technique was used, which revealed that the peak residual stress (230 MPa) is induced at 6 mm from the weld surface and falls into the tensile stress category.

Investigation of microstructure, mechanical, and corrosion behavior of nickel-based alloy 625/duplex stainless steel UNS S32205 dissimilar weldments using ERNiCrMo-3 filler metal

Evaluation of microstructural and mechanical properties of dissimilar Inconel 625 nickel alloy–UNS S32205 duplex stainless steel weldment using MIG welding

Influence of filler materials on GTAW dissimilar welds: Inconel 718 and austenitic stainless steel 304L

Microstructural and mechanical investigation of dissimilar U-groove weld of IN 718/ASS 304L employing ERNiCr-3 filler

Investigation on microstructural and mechanical integrity of GTAW dissimilar welded joint of IN 718/ASS 304L using Ni-based filler IN 625 using EBSD and DHD techniques

Effect of filler metal composition on microstructural and mechanical characterization of dissimilar welded joint of nitronic steel and super duplex stainless steel

Characterization of microstructure and mechanical properties of nickel based superalloy 617 by pulsed current gas tungsten arc welding technique

Investigations on microstructural characteristics and mechanical properties of 316 L stainless steel welded joints using nickel coated filler material by gas tungsten arc welding

Studies on residual stresses and structural integrity of the dissimilar gas tungsten arc welded joint of sDSS 2507/Inconel 625 for marine application

Microstructure and tensile-shear behavior of dissimilar resistance spot welds between 2304 duplex stainless steel and Inconel 718 superalloy

Analyzing microstructural, residual stress, and mechanical characteristics in dissimilar welds of Inconel 59 and AISI 904L through double-pulsed gas metal arc welding

Corrosion Properties and Impact Toughness of 2205 Duplex Stainless Steel after TIG Welding*

CHARACTERIZATION OF MICRO STRUCTURAL AND MECHANICAL PROPERTIES OF INCONEL 625/A 517 HIGH STRENGTH QUENCHED AND TEMPERED STEEL DISSIMILAR WELDS

Residual stress analysis, microstructural characterization, and mechanical properties of tungsten inert gas-welded P92/AISI 304L dissimilar steel joints

Dissimilar Rotary Friction Welding of Inconel 718 to F22 Using Inconel 625 Interlayer

Study on Creep Rupture Properties of Inconel 617B and 10%cr Steel Dissimilar Metal Weld

Characterization of Welded Joints of Dissimilar Nickel-Based Superalloys by Electron Beam and Rotary Friction Welding

Experimental Investigation On The Microstructure And Mechanical Properties Of Dss2205 And Ss304L Dissimilar Weldments

On the investigation of microstructure and mechanical properties of the AlCoCrFeNi 2.1 /316 L dissimilar spot-welded joint

Study on Effect of Nickel Molybdenum Coated Filler in Gas Tungsten Arc Welding

Effect of nickel-based filler metal types on creep properties of dissimilar metal welds between Inconel 617B and 10% Cr martensitic steel