Abstract:The grain boundary segregation and precipitation and associated deformed microstructure under cryogenic-temperature and dynamic-loading conditions were systematically investigated by means of high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM), transmission electron microscopy (TEM), high-resolution TEM (HRTEM) and electron back-scattered diffraction (EBSD). The studied steels exhibit equiaxed grains with a similar grain size of 12.0-13.3 mu m. The twinning and dislocation slip were observed as the main deformation modes under cryogenic-temperature and dynamic-loading conditions. However, the secondary twinning system is suppressed and plastic deformation by dislocation slip is small in the steel annealed at 800 degrees C for 3 h, leading to a significant decrease in Charpy impact toughness at - 196 degrees C. The HAADF-STEM results show that there are numerous (Cr,Mn)(23)C-6-type carbides along grain boundaries and the Cr or C peaks have been detected at grain boundaries without (Cr,Mn)(23)C-6-type carbides in the steel annealed at 800 degrees C for 3 h, whereas these carbides and Cr or C peaks were not observed in the steel annealed at 300 degrees C for 3 h. However, the Mn, P, S, Si and Cu peaks were not observed at grain boundaries in both steels by means of STEM-EDX. The critical shear twinning stress is high in the steel annealed at 800 degrees C for 3 h due to heavier grain boundary segregation. Meanwhile, the local stress concentration at grain boundaries may be relaxed because the crack may easily nucleate at grain boundaries whose cohesion is weakened by heavier grain boundary segregation or (Cr,Mn)(23)C-6-type carbides/matrix interfaces whose bonding strength is relatively small. Therefore, the secondary twinning system is relatively hardly activated and plastic deformation by dislocation slip is relatively small for the steel annealed at 800 degrees C for 3 h.

Effects of Cryogenic Treatment and Tempering on Mechanical Properties and Microstructure of 0.25C-0.80Si-1.6Mn Steel

Effects of cryogenic treatment on mechanical properties and crystal orientation of 0.25C-0.80Si-1.6Mn steel with extraordinary strength-toughness

Effect of Deep Cryogenic Time on the Microstructure and Mechanical Property of Cr-Mn-Si High-Strength Alloy Steel

Effect of tempering and deep cryogenic treatment on microstructure and mechanical properties of Cr–Mo–V–Ni steel

Study of Cryogenic Treatment on the Microstructure and Mechanical Properties of Marine 10Ni5CrMoV Steel

Effects of traditional heat treatment and a novel deep cryogenic treatment on microstructure and mechanical properties of low-carbon high-alloy martensitic bearing steel

Microstructural variations and mechanical properties of deep cryogenic treated AISI M35 high-speed steel tempered at various temperatures

Effect of Deep Cryogenic Time on Martensite Multi-Level Microstructures and Mechanical Properties in AISI M35 High-Speed Steel

Effect of multiple deep cryo-treating and tempering on microstructure and property evolution of high carbon bearing steel

Enhancing Ductility of Martensitic Steels Through Cryogenic Treatment

Elucidating the role of secondary cryogenic treatment on mechanical properties of a martensitic ultra-high strength stainless steel

Influence of Deep Cryogenic Treatment and Secondary Tempering on Microstructure and Mechanical Properties of Medium-Carbon Low-Alloy Steels

Tailoring the Microstructure to Enhance the Cryogenic Mechanical Properties of a Fe–34.5mn–0.04c Steel

The effects of room temperature soaking and deep cryogenic treatment on the stress relief phenomenon of Ti-Mo maraging stainless steel

Interpretation of microstructure evolution and mechanical properties under aging treatments of a Fe–24Mn-0.6C–2Al-0.6V austenitic steel for cryogenic application

Interpretation of Significant Decrease in Cryogenic-Temperature Charpy Impact Toughness in a High Manganese Steel

Effects of deep cryogenic treatment on microstructural evolution and alloy phases precipitation of a new low carbon martensitic stainless bearing steel during aging

Effect of deep cryogenic treatment on the mechanical properties of tool steels

Effect of Quenching and Tempering Treatment on Microstructure and Mechanical Properties of CSS-42L Bearing Steel

Temperature dependence of the deformation behavior and mechanical properties of a Fe–Mn–Al–C low-density steel for cryogenic application