Abstract:Abstract Helical flow of non-Newtonian fluids in concentric and eccentric annuli is of great interest in oil/gas well drilling. Experimental results and field measurements demonstrated that frictional pressure loss in the annulus can be affected substantially by the rotation of the drillpipe. Previous studies indicated that the influence of pipe rotation on annular friction pressure loss is affected by fluid properties, flow regime, annular diameter ratio and eccentricity. This article presents results of in-depth experimental and theoretical investigations conducted on the flow of yield power law (Herschel Buckley) fluids in concentric and eccentric annuli with pipe rotation. The aim of this study is to develop a reliable hydraulic model that accounts for the effect of pipe rotation in annular pressure loss calculations. Extensive flow experiments with polymer-based fluids were carried out using a newly developed testing facility. Four different annular geometries have been considered for the investigation. Five different formulations of test fluid were prepared by varying concentrations of Xanthan Gum (XG) and Polyanionic Cellulose (PAC) for each annular geometry. Accurate fluid characterization was made using the horizontal pipe sections and a rotational viscometer. In addition to the experimental work, theoretical analysis of helical flows in concentric annuli was carried out. Experimental results indicate the strong presence of shear thinning and inertial effects when inner pipe rotates. In highly eccentric annuli, inertial effects dominate the phenomenon of shear thinning and result in increased pressure loss as the speed increases. Inertial effects can be generated due eccentricity and/or geometric irregularities of the annulus that substantially influence the velocity field as the pipe rotates. The experimental measurements and theoretical analysis presented in this investigation are very useful for hydraulic program optimization and well control, particularly for managed pressure drilling (MPD) operations. Introduction Helical flow of non-Newtonian fluids in concentric and eccentric annuli is of great interest in oil well drilling. Laboratory test results 1–7 and field measurements 8–16 demonstrated that frictional pressure loss in the annulus can be affected substantially by the rotation of the drill pipe. The effect of pipe rotation on friction pressure loss is mainly influenced by fluid properties (rheology and density), flow regime, diameter ratio and eccentricity. The change in friction pressure loss due pipe rotation is attributed to different flow phenomena such as:shear thinning in non-Newtonian fluid;inertial effects resulting from pipe eccentricity and/or geometric irregularities such as drillpipe wobbling or eccentricity variation and;formation of secondary flows. Shear Thinning: Shear thinning in non-Newtonian flows tends to reduce the friction pressure loss due to the coupling of axial and rotational flow through shear rate dependent apparent viscosity function. Inertial Effect: Streamlines in concentric annular flow form perfectly helical pattern. This means that the magnitude of velocity of a fluid element at a given radius from the center is constant. However, a rotating eccentric pipe and/or wobbling drillpipe generates very complicated flow patterns in the annulus, resulting in substantial variation of the velocity of a fluid element along the streamline. Consequently, the inertial effects that positively influence the friction pressure loss counteract the effect of shear thinning in eccentric annuli.

Determination of the characteristics of a jet pump during its asymmetric rotation in a well

Experimental and numerical investigations on pressure pulsation in a pump mode operation of a pump as turbine

New Method to Determine the Dynamic Fluid Flow Rate at the Gear Pump Outlet

Steady and Unsteady Flow Characteristics inside Short Jet Self-Priming Pump

Effect of Rotational Speed on Performance of Mixed Flow Pump as Turbine

Analysis of flow in liquid jet pump—Part Ⅰ:Experiment and three-dimension numerical simulation

Rotordynamics of a Two-Phase Flow Twin Screw Pump

A numerical investigation on the vortex formation and flow separation of the oscillatory flow in jet pumps

Experimental Study and Modeling of Yield Power-Law Fluid Flow in Annuli with Drillpipe Rotation

Numerical Simulation and Computational Flow Characterization Analyses of Centrifugal Pump Operating as Turbine

Numerical Analysis of Non-Axisymmetric Flow Characteristic for a Pump-Turbine Impeller at Pump Off-Design Condition

A Generalized Hydraulic Model for Propulsion Force Calculations in Radial Jet Drilling

Computational Analysis on Numerical Simulation of Internal Flow Physics for Pump as Turbine in Renewable Small Hydro Energy Generation

Influence of the jetting fluid on the internal flow in a centrifugal pump with jetting device

Jet pumps for thermoacoustic applications: design guidelines based on a numerical parameter study

Numerical Analysis of Unstable Turbulent Flows in a Centrifugal Pump Impeller Considering the Curvature and Rotation Effect

Unsteady Flow Behaviors and Vortex Dynamic Characteristics of a Marine Centrifugal Pump under the Swing Motion

The comparative transient prediction on hydrodynamic characteristics and flow field properties of pump-jets with accelerating and decelerating ducts

Investigation of Flow Instability Characteristics in a Low Specific Speed Centrifugal Pump Using a Modified Partially Averaged Navier–Stokes Model

Unstable Flow Characteristics in a Pump-Turbine Simulated by a Modified Partially-Averaged Navier-Stokes Method

Numerical Simulation and Uncertainty Analysis of an Axial-Flow Waterjet Pump